similar to: Detecting off-hook state on extension

Displaying 20 results from an estimated 10000 matches similar to: "Detecting off-hook state on extension"

2003 Jun 25
2
Asterisk - first impressions
I'm still a newbie in Asterisk, just yesterday installed it for home use (so I can call home while travelling). Using AVM A1 (BT Speedway) ISDN card. Anyway, I find it very hard to locate supporting information for Asterisk. User's Handbook is still a draft, this mailing list is not easily searchable, and any info out on Usenet is scarce. I spent some 30mins just trying to find out naming
2003 Jun 30
3
MGCP with Cisco doesn't work
I'm trying to link up Cisco MGCP-enabled router (residential gateway) with Asterisk, and it looks like some sort of protocol mismatch, could it be MGCP 0.1 vs 1.0? Look at this (x.x.x.99 is the router, x.x.x.98 is Asterisk): MGCP read: NTFY 2 aaln/0@voip-gw1 MGCP 0.1 X: 0 O: hd from 192.168.154.99:2427MGCP read: NTFY 2 aaln/0@voip-gw1 MGCP 0.1 X: 0 O: hd from 192.168.154.99:2427Verb:
2003 Oct 27
2
SIP & IAX behind NAT
I'm trying to set up * server behind NAT. The box is set up as DMZ in my DSL router, i.e. all incoming connections without explicit port mapping are forwarded to *. So far I'm unable to get this setup to work for either IAX or SIP (tried IAXComm & XLite softphones on public IP address). Data seems to come in fine (IAX/SIP debug shows message interaction taking place), but there is no
2005 Jun 20
6
Extension Configuration Best Practice
Guys. I would like to hear tips and tricks on extention config best practices, for example, naming, etc. and most of all, how to deal with extention that have a full time hardphone configured and assigned and then a softphone connecting to the same extention, for example, one employee has its hardphone on the office but sometimes when he travel, he uses his softphone to work with, what happens
2003 Jun 25
4
Asterisk and FWD
I can't get my Asterisk to register/place calls with FWD. Here's what I have in my SIP.CONF: register => 11111@fwd.pulver.com/11111 [fwd] type=friend secret=somesecret host=fwd.pulver.com username=11111 fromuser=11111 fromdomain=fwd.pulver.com I'm using CVS version of Asterisk, checked it out last week. I get authenticate error when registering with fwd, and all my calls to
2006 Nov 12
2
same extension on softphones and hardphones
Sorry if you see this message repeated twice. I would like to set up hard phones and softphones with the same extension so that when anybody in the company dials an extension, each user's hardphone and softphone will ring at the same time. I've tried setting this up before, but I noticed that the last sip device to register with the same extension is the only one that rings when the
2003 Oct 20
1
mgcp transfer takeback with ata186 (logs with comments - long post)
Hi, in following of a recent discussion I got to work on MGCP with the Cisco ATA186 again, and got it to work very nicely. However, there is a little thing with transfers I would like to get comments on: Call comes in from PSTN and goes to an ATA186 (MGCP) Call is answered and then, using flash, transferred to another extension If the extension is available, there can be an announcement and
2005 May 20
2
MGCP 1.0 / NCS 1.0
I'm trying to use a 4 port ATA that was designed for use with MGCP 1.0 / NCS 1.0 -- is the channel_mgcp compat with NCS -- anything I can do to make it compat?? This is what happens - below *CLI> mgcp reload Reloading MGCP == Parsing '/etc/asterisk/mgcp.conf': Found Use EXIT or QUIT to exit the asterisk console == MGCP Listening on 10.1.22.39:2427 == Using TOS bits 0 mgcp
2004 May 19
1
One-way audio with H.323 --> SIP call
Good day, I have a puzzling issue that people in the IRC channel recommended I post to the list so here goes :) I am trying to call a SIP softphone from an H.323 hardphone. The hardphone is connected to a Definity Prologix R12 PBX with a MedPro card and a CLAN. The Avaya is setup to send any call to extension 1609 down an H.323 trunk group that is destined for the Asterisk server. When I call
2003 Dec 29
1
transfer with MGCP
Hello, I`m try to make the attended transfer work Dlink DG-104S via FLASH, when somebody calls my phone I pickup and press flash to get a second line to call another extension. When I press flash I hear no dialtone, and only a long and then small beep. When I try to dial digits I hear again those long+short beeps, but the extension dialed is not ringing. If I pres flash again I get back to
2009 Dec 17
2
Integrate a CPE with Asterisk in MGCP
Hello all, I'm looking for some help to try to understand why my CPE doesn't work good with Asterisk in MGCP. Here is what I want to do : - Register a TECOM AH4021 on Asterisk in MGCP with the following profile in mgcp.Conf : [general] port = 2727 bindaddr = 10.95.20.1 disallow=all allow=g729 allow=alaw 020202020202] context=mgcp host=dynamic canreinvite=no dtmfmode=rfc2833 nat=yes
2003 May 19
1
MGCP and Cisco ubr924
I've been trying to figure this one out for a while, but to no avail. I have my cisco ubr924 setup for MGCP with Asterisk as the call-agent. I have manually registered the endpoint in mgcp.conf. When I pick up the phone, I get no dialtone and debug shows errors. IOS on the ubr924 is 12.2. Any help is appreciated. from mgcp.conf: [ubr924] host=65.37.86.203 context = from-sip (just as a
2005 May 16
1
ShoreTel 210 MGCP phone drops calls with MGCP RSIP
I've got a ShoreTel 210 MGCP phone drops calls. My packet capture indicates that the phone may be trying to renew its registration with *, but reports Restart Method of Disconnected (frame 2), then * seems to take that as a sign that it has lost the connection and closes things down. The phone, meanwhile, seems to think it can continue the conversation until a few ICMP "port
2004 Oct 15
1
Asterisk crashes on special Transfer with MGCP/ATA 186
Hi all, i am using CVS-HEAD-08/13/04-12:00:00-BRI-stuffed-0.1.0-RC4a with Cisco ATA-186 3.1.1 atamgcp We are used to make an special ;) blind transfer like (Flash)Number(Hangup before anyone answers or ring). Then * crashes (see below) if the man in the middle is an cisco-ata-186-mgcp If one waits until the last one rings, then hangup, everything is fine. If one waits until the last one
2004 Jan 22
2
MGCP Problem.
Hi. I'm new in Asterisk with MGCP. I set up a MGCP user agent and start asterisk with the next configuration files. '--------------- extensions.conf ---------------------------------------------------- [general] static=yes writeprotect=yes [globals] ap1 => mgcp/aaln/ap200@64.76.148.186 [macro-apl1] exten => s,1,Dial(${ARG1},30,Ttmr) ;exten => s,2,Voicemail(u${MACRO_EXTEN})
2004 Jan 22
3
MGCP w/8x8 DTA-310 and as5300 pstn gateway
Hello folks, I'm trying to get an 8x8 DTA-310 running mgcp to work. I get no dialtone & can't get it to ring. My mgcp.conf says: ; ; MGCP Configuration for Asterisk ; [general] port = 2427 bindaddr = 0.0.0.0 [172.16.2.25] host = 172.16.2.25 context = default line => aaln/1 And here's the interesting bits of extensions.conf: [globals] ... TRUNK=H323/BYEXTENSION@pstn_gw ...
2003 Apr 24
3
new mgcp patch errors
see below I tried to call 98013356 from the following phone (from mgcp.conf) [iptlf03] host = 192.168.33.3 context = default inbanddtmf = 1 callerid = 22545062 line => aaln/1 Console output: == Spawn extension (capiring, 9988001133335566, 1) exited non-zero on 'MGCP/aaln/1@iptlf03-1' -- MGCP mgcp_hangup(MGCP/aaln/1@iptlf03-1) on aaln/1@iptlf03 -- Delete connection 4
2003 Jul 11
3
mgcp problems
I strange error messages when using mgcp and ata186 . This session is simply dial into 600 demo extension - echo test ... Handling request 'NTFY' on aaln/1@10.0.1.19 Transmitting: 200 29 OK to 10.0.1.19:2427 -- Endpoint 'aaln/1@10.0.1.19-1' observed '0' -- MGCP Asked to indicate tone: on aaln/1@10.0.1.19-1 in cxmode: sendrecv Posting Request: RQNT 306
2004 Dec 22
1
MGCP Transaction identifiers
I know this is not the most appropriated list to this, but I will try: Does anyone know what is the criteria to the generation of the transaction identifiers in MGCP? I mean, are they generated by a randomic method? I'm using Asterisk and MGCP eyeP Phone and observed that the RSIP and NTFY (methods created by the gateway) use high values in the transaction identifiers, while the RQNT, AUEP,
2005 Mar 25
2
MGCP issue
Hello List, I'm trying to setup MGCP channel with a Centile Media Hub box. My Centile box has 4 ports and I got no dial tone. Can somebody help with this isuue? This is my mgcp.conf and extensions.conf Thanks Daniel. ; MGCP Configuration for Asterisk ; [general] port = 2427 bindaddr = 192.168.11.20 disallow=all allow=g729 allow=alaw allow=ulaw [192.168.11.200] context=MGCP