similar to: Asterisk ALSA module not working

I have a software-only PBX set up. I can register various softphones and they will call each other -- but I've never succeeded in getting any voice routed from any of the softphones. Only the console will transmit audio. I am writing to ask if I have missed some obvious step in configuring the system. Conditions: (1) Softphones running on the same machine as the PBX: Only Kphone seems

I've built the latest CVS of asterisk -- not the zaptel or libpri directories, just the asterisk directory. asterisk installs successfully, but there are severe problems. I built this system in the past and ran it, but now building it again fails. This is the CVS as of this morning, 2003-06-13, but I had problems on 06-11/12 as well. After make; make install; make samples; make config, I

Hi guys, Being a true Linux geek, I've never been too much into sounds or sound files other than a few .mp3 songs I got. My question is pretty straightforward and simple. I see that the music format of choice for asterisk is .gsm. What can I use to listen to files in .gsm format and what is the most effective way of recording files into .gsm format? The last part of the question is

Today's "frustrated programmer" award goes to Linphone, which has the following debug output: > (linphone:28655): LinphoneCore-WARNING **: this fucking remote sip phone did not answered properly to my sdp offer! I get this message when I connect to linphone using a softphone, or when I try to use linphone to connect to asterisk and listen to an announcement. I suspect that

>> See if it plays back properly. > > Running aplay as asterisk user seems to be no problem: > > asterisk at puppy$ aplay /usr/share/sounds/alsa/Front_Center.wav > Playing: WAVE '/usr/share/sounds/alsa/Front_Center.wav' : Signed 16 bit > Little Endian, Rate: 48000 Hz, mono > asterisk at puppy:~$ aplay -Dpulse /usr/share/sounds/alsa/Front_Center.wav >

Hello, I can't get the sound over alsa to work with Asterisk. My current version is 1.4.21.2~dfsg-3 running on debian stable. All settings are the default ones with exception of: /etc/asterisk/modules.conf: load => chan_alsa.so noload => chan_oss.so /etc/asterisk/alsa.conf: input_device=default output_device=default asterisk is started up and doesn't complain about alsa in

Anyone know of anybody doing VXML with Asterisk and/or Linux? Tia Kevin

I am trying to get a console/dsp application going with 1.4.18 and not hearing any audio. In the CLI I see the call coming in, I see the Dial(Console/dsp) I see <auto answered> I see ALSA default but I hear no audio. What can I do to tell what is happening here. I have in modules.conf: noload chan_oss.so load chan_alsa.so For kicks I tried it the other way to noload chan_alsa.so and load

Does anyone know what this means? It is in DMESG, and we have people complaining about echo. Disabled echo canceller because of tone (rx) John

Hi ... probably one of those RTFM kind of questions (while I'd be happy to know where a good reference "FM" is :-) ) Has anyone an idea on how to disable the console sound driver. My problem is that a running asterisk is muting my speakers. Thank you in advance for your help Conrad

Why hasn't someone found 50 people who sound alike, put them in sound studios and record the 10,000 most commonly used words. You would all differnent forms of the 1,000 most words, i.e. leading, trailing, question etc. You can synthesize the other 0.05% when you run into them. With hard drives so big, processors so fast and EXT3 that can handle 30,000+ files in a single directory that

All the clients that I'm aware of for IP telephony have drawbacks. Some won't work at all. KPHONE -- Kphone works best for me, but Kphone doesn't have a dialpad to dial tones during the middle of the call, so the demo that * comes with can't be run. Kphone (3.1, the latest) also has a habit of crashing if you do something even mildly stressful, such as hang up while Kphone is

Hi list! Currently I use Asterisk 1.8.30.0 on an OpenWRT-Switch. Now I want to change to Asterisk 13.14.1 on a Banana PI (with Armbian/Debian 9). Well, I copied the configuration and changed what needed, so basically, it works, at least with my tests. But when Asterisk will be started, in the message log I get this error: [Feb 15 08:40:15] ERROR[3971] chan_oss.c: Unable to register channel

Hello, I have a strange situation: I can talk to other SIP phones and via ISDN to the outside, but I don't hear playbacks or the voicemail messages. Asterisk show in the cli, that the corresponding files are played, but I hear nothing at all. Here is as simple example: [monkeys] ??? exten => 99,1,ANSWER() ??? exten => 99,2,PLAYBACK(tt-monkeys) ??? exten => 99,3,HANGUP() The phone

I have just installed the Alsa drivers for my 2.4.18-14 kernel (RH8). I have configured the sound card ok with alsaconf and tested with the aplay , works fine. But when I run asterisk it says.. ------------------------------- [chan_alsa.so] => (ALSA Console Channel Driver) Apr 20 18:28:34 ERROR[8192]: chan_alsa.c:339 alsa_card_init: snd_pcm_open failed: No such device or address Apr 20

Hi I?m a new user and I do test with my hardware . I have a x100p and telephone vozip. And when I run this command asterisk ?vvvvc for to test it . My computer show it ?warning? [chan_iax.so] => (Inter Asterisk eXchange) == Manager registered action IAX1peers == Parsing '/etc/asterisk/iax1.conf': Not found (No such file or directory) Apr 2 07:45:12 ERROR[16384]:

strace on file access in asterisk shows that * is not even attempting to access the voice files. If I *manually* load app_playback.so, app_macro.so, and then pbx_config.so, I they will load and I get a dialplan. Ok, that's a problem -- autoconf is clearly not working, or there's some other related issue. So I try to use the demo and do "dial 500". This should connect and

Zitat von Tzafrir Cohen <tzafrir.cohen at xorcom.com>: Hi, > Off-topic: any reason you don't use chan_alsa? This was the "Armbian installation", I didn't configured it extra... > Are you sure you quote the error message right? Copy+Paste... ;) But I searched a little bit and I really don't think, I need this module... As I undestand, I just need it, if I

On 16-08-16 04:38, George Joseph wrote: > > > On Mon, Aug 15, 2016 at 1:24 PM, Jonas Kellens > <jonas.kellens at telenet.be <mailto:jonas.kellens at telenet.be>> wrote: > > Hello > > using pjproject 2.5.5 > using asterisk-certified-13.8-cert1 > > > IIRC there were API changes in pjproject 2.5 that aren't accounted for > in

I got this compiling the new cvs code ... any idea ? Tnx ! gcc -pipe -Wall -Wstrict-prototypes -Wmissing-prototypes -Wmissing-declarations -g -Iinclude -I../include -D_REENTRANT -D_GNU_SOURCE -O6 -march=i686 -DZAPTEL_OPTIMIZATIONS -DASTERISK_VERSION=\"CVS-04/07/04-11:28:50\" -DINSTALL_PREFIX=\"\" -DASTETCDIR=\"/etc/asterisk\"