similar to: Fax support over MGCP, H323 and SIP in asterisk

Hi List I have one question about MGCP in asterisk. I have a media gateway, and I want to have asterisk to work with the media gateway. As I was told that the media gateway can communicate with the switch via standard interface MGCP/ICGP. Question is if the asterisk MGCP supports such MGCP message ??? Thanks. George Lin

Hello, I try to place a call between CISCO IP phone 7905 (h323) and an analogue telephone on DLINK DG-104S (mgcp). Call setup is handled ok - both way, but after connection of the call I get both site no-audio, even codec are Set to alow-64 both. The call is terminated with this debug output - Didn't get a frame from channel: MGCP/aaln/1@dlink-1 and is Hanged up. Jan 18 20:32:55

Hello folks, I'm trying to get an 8x8 DTA-310 running mgcp to work. I get no dialtone & can't get it to ring. My mgcp.conf says: ; ; MGCP Configuration for Asterisk ; [general] port = 2427 bindaddr = 0.0.0.0 [172.16.2.25] host = 172.16.2.25 context = default line => aaln/1 And here's the interesting bits of extensions.conf: [globals] ... TRUNK=H323/BYEXTENSION@pstn_gw ...

Hi, I havn't actually tried this yet, but would it be possible to use asterisk as a mgcp <-> h.323 translator? For example, I have mgcp service from Next Gen telephone company. But i only have a h.323 phone. Would there be a way to the mgcp signalling to hit asterisk, and then have it fire the call out h.323? And vice versa? Just brainstorming. Sean Watkins

I've got a ShoreTel 210 MGCP phone drops calls. My packet capture indicates that the phone may be trying to renew its registration with *, but reports Restart Method of Disconnected (frame 2), then * seems to take that as a sign that it has lost the connection and closes things down. The phone, meanwhile, seems to think it can continue the conversation until a few ICMP "port

> Hello all, > Can someone help me on the problem which I have on MGCP phone test . I test mgcp - asterisk- zap. But I got several NOTICE message from rtp.c. > NOTICE[20501]: File rtp.c, Line 221 (process_rfc3389): RFC3389 support > incomplete. Turn off on client if possible > > -- Endpoint 'aaln/1@VG101-1-1' observed '9' > NOTICE[20501]: File rtp.c,

Hello, I`m try to make the attended transfer work Dlink DG-104S via FLASH, when somebody calls my phone I pickup and press flash to get a second line to call another extension. When I press flash I hear no dialtone, and only a long and then small beep. When I try to dial digits I hear again those long+short beeps, but the extension dialed is not ringing. If I pres flash again I get back to

I've been trying to figure this one out for a while, but to no avail. I have my cisco ubr924 setup for MGCP with Asterisk as the call-agent. I have manually registered the endpoint in mgcp.conf. When I pick up the phone, I get no dialtone and debug shows errors. IOS on the ubr924 is 12.2. Any help is appreciated. from mgcp.conf: [ubr924] host=65.37.86.203 context = from-sip (just as a

Hi all, I have VOIP network built with MGCP endpoints.The manufacturer of endpoints is ASKEY. I downloaded latest Asterisk software and found it very useful for me. I configured it and it seems taht everything works OK when I am testing it with one or two endpoints. After that I tried to move Asterisk to working network and replace existing call manager. It starts working and calls are

Hi all, i am using CVS-HEAD-08/13/04-12:00:00-BRI-stuffed-0.1.0-RC4a with Cisco ATA-186 3.1.1 atamgcp We are used to make an special ;) blind transfer like (Flash)Number(Hangup before anyone answers or ring). Then * crashes (see below) if the man in the middle is an cisco-ata-186-mgcp If one waits until the last one rings, then hangup, everything is fine. If one waits until the last one

I know this is not the most appropriated list to this, but I will try: Does anyone know what is the criteria to the generation of the transaction identifiers in MGCP? I mean, are they generated by a randomic method? I'm using Asterisk and MGCP eyeP Phone and observed that the RSIP and NTFY (methods created by the gateway) use high values in the transaction identifiers, while the RQNT, AUEP,

The problem I have had with many SMS email gateways, is that they do not allow to reply back. Of course, email is a superior service over SMS, but does not really replace it ( - at least not until all the mobile phones have email access on them...). It would be nice if the SMS service would be available not only on GSM/GPRS/etc., but also on any telephone number in the world - or at least on

hi all I'm being spammed by these messages in the console (see below) and sound doesn't work with today's cvs. I rolled back a week, and it works fine. In addition to the sound problems, I had to enable inband dtmf squelch on the dilnk mgcp phones. if not, each pressed key was counted twice NOTICE[245776]: File chan_mgcp.c, Line 710 (mgcp_rtp_read): MGCP ast_dsp_process

see below I tried to call 98013356 from the following phone (from mgcp.conf) [iptlf03] host = 192.168.33.3 context = default inbanddtmf = 1 callerid = 22545062 line => aaln/1 Console output: == Spawn extension (capiring, 9988001133335566, 1) exited non-zero on 'MGCP/aaln/1@iptlf03-1' -- MGCP mgcp_hangup(MGCP/aaln/1@iptlf03-1) on aaln/1@iptlf03 -- Delete connection 4

I strange error messages when using mgcp and ata186 . This session is simply dial into 600 demo extension - echo test ... Handling request 'NTFY' on aaln/1@10.0.1.19 Transmitting: 200 29 OK to 10.0.1.19:2427 -- Endpoint 'aaln/1@10.0.1.19-1' observed '0' -- MGCP Asked to indicate tone: on aaln/1@10.0.1.19-1 in cxmode: sendrecv Posting Request: RQNT 306

Hello all, I'm looking for some help to try to understand why my CPE doesn't work good with Asterisk in MGCP. Here is what I want to do : - Register a TECOM AH4021 on Asterisk in MGCP with the following profile in mgcp.Conf : [general] port = 2727 bindaddr = 10.95.20.1 disallow=all allow=g729 allow=alaw 020202020202] context=mgcp host=dynamic canreinvite=no dtmfmode=rfc2833 nat=yes

Hello List, I'm trying to setup MGCP channel with a Centile Media Hub box. My Centile box has 4 ports and I got no dial tone. Can somebody help with this isuue? This is my mgcp.conf and extensions.conf Thanks Daniel. ; MGCP Configuration for Asterisk ; [general] port = 2427 bindaddr = 192.168.11.20 disallow=all allow=g729 allow=alaw allow=ulaw [192.168.11.200] context=MGCP

I'm trying to link up Cisco MGCP-enabled router (residential gateway) with Asterisk, and it looks like some sort of protocol mismatch, could it be MGCP 0.1 vs 1.0? Look at this (x.x.x.99 is the router, x.x.x.98 is Asterisk): MGCP read: NTFY 2 aaln/0@voip-gw1 MGCP 0.1 X: 0 O: hd from 192.168.154.99:2427MGCP read: NTFY 2 aaln/0@voip-gw1 MGCP 0.1 X: 0 O: hd from 192.168.154.99:2427Verb:

Hello everybody! I have an Asterisk 1.2.12.1 server with SIP as the VoIP protocol. What I want to do: I want to talk to the "outside world" via MGCP. I suppose I must set an MGCP peer to route outgoing calls. So, I must set the endpoint syntax of the Asterisk server (Asterisk will act as an MGCP gateway and will talk with an MGCP Gatekeeper) and with other MGCP gateways via

I'm trying to use a 4 port ATA that was designed for use with MGCP 1.0 / NCS 1.0 -- is the channel_mgcp compat with NCS -- anything I can do to make it compat?? This is what happens - below *CLI> mgcp reload Reloading MGCP == Parsing '/etc/asterisk/mgcp.conf': Found Use EXIT or QUIT to exit the asterisk console == MGCP Listening on 10.1.22.39:2427 == Using TOS bits 0 mgcp