similar to: cyclades driver on centos 4.1

I hope this isn''t too far off topic. I did a little bit of pricing homework a few months ago on new T1 cards. The idea was to build a Linux based router/firewall. After all, Ethernet NICs are easily available for less than $10 today. But all the T1 cards I found cost a fortune. And about a year ago, I learned the list price for a complete Adtran Netvanta 3200 router with T1 card is

Hi. I have a Cyclades PC300/TE2 card that turns a Linux PC into a Dual T1 interface router. It is well made and high performance. I used it for a few years. It includes two T1 cables. Cyclades has gotten out of this business but the Linux kernel developer community supports this card so no additional driver is needed. It cost me $700+. I would like to sell it for about $300. Put this in a PC

How about a PCMCIA Zapata interface?? Asterisk and its strength kick ass as a test unit. Can't do some of the things a T-byrd can do but the Telco techs freak when you tell them its your PBX!!! ) 10. Re: The Smallest Asterisk Server Ever? (Panny Malialis) Message: 10 From: "Panny Malialis" <panny@hotlinks.co.uk> To: <asterisk-users@lists.digium.com> Subject: Re:

All, I have an old computer 64M 350Mhz pentium II. centos os 4.1 installs on it fine. however on boot it says low memory and it kills certain processes. httpd or sendmail. I have a 2GIG swap and I did a chkconfig XXX off on a few things like xfs, nfs, httpd, kudzu. My old 2.4 kernel used to run in 4M with a swap... I had recompiled the kernel (took a while) to enable the cyclades module. Any

I am trying to plug a USB 2 device in a USB 3 slot. Nothing is being detected in "lsusb". Is there something special I need to do? I am running centos 5.5 x86_64. I thought 3.0 was backward compatible. Nothing special about my device its an RS232 to USB device. It works in 2.0 slot. Thanks, Jerry

I downloaded the kernel from kernel.org. I did the following: cd /usr/src tar -jxf /tmp/linux-2.6.17.3.tar.bz2 cd linux-2.6.17.3 make menuconfig selected what I needed, saved the new config make bzImage make modules At this point nothing is compiled. All I get is: CHK include/linux/version.h Building modules, stage 2. MODPOST and a command prompt. I did make menuconfig again and it

I all, I was thinking about installing centos on a usb flash drive. Perhaps a 4GIG. I dont need X or anything on this drive so installing should fit just fine. Are there boot issues with these flash drives? I'll be using a newer motherboard so the motherboard should be able to boot USB. Does this work? Have others done anything with flash drives? I am wanting this flash drive to be the

Is there something in CentOS/linux that would take a single input in my case RS232 port and deliver that to two connecting network ports? So two devices can get the single port data. Thanks, Jerry

Hi, I''m trying to configure QoS on my linux in the following manner: I have a main link with 64K, so I divided it in 3 classes of 18K, 14K and 9K with an excess (not used for classified traffic, just to be shared) of 23K. This excess should be distributed proportonally among the 3 classes, that is, the class that has more rate should borrow more bandwidth. What is happening is

Hi all, I have donwloaded 2.6.32.59 from kernel.org, extracted the source, did make menuconfig to select/deselect items then did make bzImage, make modules, make modules_install, make install and rebooted. first message I got was that ext4 was not supported. So I verified that ext4 was selected and it was. So I looked at the size of the /boot/initramfs* items. My custom one is really small

Hi all, I have a user who is reporting excessive amounts of lost characters when using SYSLINUX (PXELINUX actually) over a serial port at 38400 bps. What is somewhat bizarre is that he has a very high quality server with a Cyclades board, and yet he's losing characters in the PXELINUX->server direction. Has anyone else seen this? Thanks, -hpa

On Tue, 28 May 2019, nicolae788 wrote: > Apc uses a propietary serial cable and your convertar for sure it's wired > standard. Refer to the following link for info. > https://pinoutguide.com/UPS/apc_smart_cable_pinout.shtml > > Good luck > > On Tue, 28 May 2019, 15:13 , <grumpy at mailfence.com> wrote: > >> a friend gave me an old apc smart-ups 1250

On 5/28/19 3:39 PM, Julian H. Stacey wrote: > grumpy at mailfence.com wrote: >> a friend gave me an old apc smart-ups 1250 >> it has a rs232 interface but i have no pc with a rs232 port >> i attempted to use a rs232 to usb adapter but the ups goes nuts >> i connected the ups to batteries and verified it was working properly >> when i plug the usb cable into the pc

Hi, Reference: > From: Manuel Wolfshant <wolfy at nobugconsulting.ro> > Date: Tue, 28 May 2019 16:42:21 +0300 Manuel Wolfshant wrote: > On 5/28/19 3:39 PM, Julian H. Stacey wrote: > > grumpy at mailfence.com wrote: > >> a friend gave me an old apc smart-ups 1250 > >> it has a rs232 interface but i have no pc with a rs232 port > >> i attempted to

I have a select box in my view, with an option for select, a variable for selected value, and an Ajax observe_field <select name="most[criteria]" id="most_criteria" style="display:inline;width:12em;" > <%= options_for_select({ "most cheerful" => "1", "most beautiful" => "2", "most displayed" =>

Suggestions? ----- Forwarded Message ---- From: James Tucker <jt at ra66i.co.uk> To: djberg96 at yahoo.com Sent: Thursday, October 19, 2006 7:28:30 AM Subject: Win32 OVERLAPPING IO Hi Daniel, My name is James Tucker, I''ve been hacking in Ruby for only a few months now, however am an experienced general programmer in a wide variety of languages. My current focus is on a new

grumpy at mailfence.com wrote: > a friend gave me an old apc smart-ups 1250 > it has a rs232 interface but i have no pc with a rs232 port > i attempted to use a rs232 to usb adapter but the ups goes nuts > i connected the ups to batteries and verified it was working properly > when i plug the usb cable into the pc the ups shuts down > when i attempt to turn it on it beeps twice

Apc uses a propietary serial cable and your convertar for sure it's wired standard. Refer to the following link for info. https://pinoutguide.com/UPS/apc_smart_cable_pinout.shtml Good luck On Tue, 28 May 2019, 15:13 , <grumpy at mailfence.com> wrote: > a friend gave me an old apc smart-ups 1250 > it has a rs232 interface but i have no pc with a rs232 port > i attempted to use

Hi all I was wondering if one of you kind gentlemen (or ladies) would assist me in finding the data string required to tell my ups to turn on and off. No more no less :) I guess it would be the actual string of an instant command sent down the rs232 port to the ups. I have no programming experience and have done a list search to no avail. Sorry to trouble you with this. I have a lan to

Hello guys. I am new in mac world and in wine apps. I have this singular situation: I have a macbook with wine and winebottler installed. I want to use this exe app: azloader.exe. Ok, wine is able to load it normally. But... the problem is, my macbook has not the RS-232 port. So I bought a RS-232 to USB adapter. I've installed the correct "drive" to use that. I've tried that in