similar to: Current SIP channel features supported

I have recently set to * to play with and I'm getting the hang of it.. I've seen various posts about problems where the SIP clients are behind NAT but I anted to ask a slightly different question. At the current CVS can the * SIP client register with a SIP provider (such as ICH) when the * box itself is behind a NAT. I have an ICH account which I can configure fine on an ATA 186 using

Hi All, I am trying to use iconnecthere to make outbound calls. I am behind a linksys router. I keep getting this error 481 "Call Leg/Transaction Does Not Exist". Does anyone have any prior experience with this problem. Any leads will be much appreciated. Attached are the conf files and logs #SIP.CONF ; SIP Configuration for Asterisk [general] port = 5060 ; Port

Hi All, Outbound Iconnecthere calls work without any problem but Inbound calls are very intermittent. It seemed to work for a week or so but over the past week 99% of inbound calls are dropped to ICH voicemail. Would moving the Asterisk box to a public IP resolve the problem or is it just an ICH/Asterisk problem? I am registering against natrelay.deltathree.com. asterisk -vvvc shows an

Hi, I wish to connect several ATA186 Phones to each other, to iconnecthere and to the PSTN using asterisk. Please tell the appropriate settings for firewall (ports to open etc.) sip.conf and extensions.conf(part relevant to iconnect). Also I would be glad to get a working example of your ATA186 configuration. I tried searching the mailing lists and several sites but did not find an answer.

Hi, I am calling from a grandstream phone with g723 codec through * to iconnect. Incoming context as well as outgoing context set to g723.1 codec in *. Call get connected and I can talk. However I get the following warning, which scrolls on my screen until I hang-up. [root@asterisk sath]# cat g723.1 - Executing SetCallerID("SIP/-08122ae0", "1001") in new stack --

Hi, I was able to connect asterisk to iconnect's service. It took me almost two hours, but it's because I was having NAT trouble. I finally discovered that you can set the iconnect host to natrealy.deltathree.com to make it work. (for those of you who, like me, don't have the time to search the archive I'll provide a working sample in a minute) My problem was sound

hi i got iconnect to work, works pretty well now except calls sometimes (more often than not) hang up after a couple of minutes.. heres a bit of the debuging Record-Route: <sip:61892142222@213.137.73.178:5060;maddr=213.137.73.176> From: sip:61892142222@natrelay.deltathree.com;tag=3281050172-73809 To: "JUSTIN XLITE" <sip:2001@61.95.68.84>;tag=as09766a78 Call-ID:

Hi, I just got a SPA-2000 in and was finally able to complete my asterisk setup. I'm making my outgoing calls through iconnecthere from the asterisk server however I'm running into a problem when placing calls. I can connect fine but when the person (or answering machine) picks up I hear them talk for a about half a second then there is a half a second pause or muted period and then the

Hi, I have a deltathree account and I can place calls but I can't receive calls. I use Grandstram sip phones. When I call my deltathree phone # the voicemail is answer :(( I need some help and solutions from the guys who allready are using deltathree. I search on Internet and I try all types of configurations... :( This is my configurations files: - sip.conf - [general] port = 5060

I am trying to get my connection to IConnecthere.com working. I didn't have a register command in sip.conf at first, so I believe that is why it was not working. However, I can't seem to get the register command correct, it just keeps timing out. Below is what I have: register=<username>:<password>@natrelay.deltathree.com I know that there is supposed to be

I can't talk through iConnectHere. The connection gets made but as soon as any sound is transmitted the call ends and the Asterisk console shows an "Unsupported Media" error as follow: Got SIP response 415 "Unsupported Media" back from 213.137.73.147 My only allowed codecs are alaw and ulaw. My sip.conf looks like: [iconnect] type=friend secret=xxxx username=yyyyyyy

I have an asterisk Redhat 9 box running 4 hardphone extensions. Inter-extension calls are crystal clear. However when I dial out through my iconnect account I get a lot of jitter. At first I thought it was my nat gateway but after I programmed on of the hardphones (budge tone 100) for direct dial to iconnect I have clear voice transmission. I have no way of explaining this. My asterisk sip.conf

Quick question for the experts: I'm seeing stuck SIP channel(s) scheduled for destruction stay open. This appears to happen after (apparently successfully) registering with a SIP peer. Any ideas where to start digging into this? I'm running today's CVS, however the problem existed before and does persist. Thanks, Kai-Uwe Example: (registration with iconnecthere.com) ast1000*CLI>

Hello all, I have a 7960 registered to asterisk. I am trying to use iconnect as my sip provider. When I send an invite to delta-three, I get the normal INVITE - 407 - INVITE exchange. The problem is, asterisk is sending the second invite using the 'dialed number' from the 7960 as the username, and not my 'username' configured in sip.conf. I believe that digest authentication

I bogged down about half way through reading the Green Book, in part because it became increasingly difficult to understand how some of the ideas related to R, as opposed to S (which I have not used). Does any reader know whether there is a document that points out differences between S and R that would be helpful in reading the Green Book? Ideally, perhaps, I need a "crib sheet" to

Hi friends, I've noticed that first register message sent by * always get rejected by the destination sip server. Then * sends a second registration message ( with Autherization section, and that get accepted by the destination host). Why is this ? Isnt there a way to tell * to send with Autothorization message the first attempt ? Asterisk sends this first 9 headers, 0 lines 11 headers,

Hello All, I have gone thru all the resources I could find on google on asterisk + iconnect and managed to get outgoing calls working. However, I cannot get incoming calls to work at all. With the sip debug on, I can see that something is happening everytime a call is received from iconnecthere, but I get an invalid tone on the caller side. The call never rings anywhere on the asterisk. Would

This morning, I received a very strange error message on the Asterisk console. The error occurs when I try to access iconnect WARNING[196621]: File chan_sip.c, Line 386 (__sip_xmit): sip_xmit of 0x80d0854 (len 649) to 213.137.73.178 returned -1: Bad file descriptor I also get this error when I try to reload: WARNING[16384]: File chan_sip.c, Line 5355 (reload_config): Unable to get IP address for

Hi, i have diffirent provider example(3 single account in deltathree, 4 account in packet8 and so on) . How this possible to make the three individual sip account in deltathree act as trunk so that i cannot get a busy call. If line one fail goto line 2 then line 3 or another trunk line 1 then line 2 then line3....I read it in asterisk at home but the script i am copying is not working .

Hello, Questions, observations, and curiosities. Maybe this is something stupid or maybe I'm doing something wrong... But... In light of the Kurt Seifried paper on SSH and SSL, I was looking for the finger prints on my various servers and known hosts files to have a little crib sheet and maybe plug the list into a database on my palm pilot. I found that ssh-keygen lists out the