similar to: ISPs with QoS for VoIP?

Has anyone gotten the voicetronix boards to work with Asterisk, what would it take? Or does anyone know where I can get 4 ports or more fxs PCI cards that do work with asterisk? Brian J. Schrock Network Engineer, RHCE, CCNA Anistone Technologies Phone: 614-798-9106 FAX: 614-573-7165 6926 Avery Rd. Dublin, OH 43017

Hi, We are looking at consolidating our lines with PRI. This will allow the elimination of many fax lines. Some of them will be replaced with this type of config ... PRI * IAX * Channel-Bank FAX We will have daggressor suppressor enabled. Is anyone doing this and should I expect smooth operation? John This e-mail was scanned and found clean by Monroe-Woodbury CSD Antivirus.

Hello, How would I go ahead a record all phone calls into and out of my asterisk server. I know the legality issues behind it, but I could always play a recording to let people know they will be recorded. Brian J. Schrock Network Engineer, RHCE, CCNA Anistone Technologies Phone: 614-537-2817 FAX: 614-573-7165 6926 Avery Rd. Dublin, OH 43017

Hello, Does anyone know what may be causing this? Asterisk was built from cvs tonight. Ztcfg also says us is an invalid tone zone. Anyone got some information on what this is, why is it happening, and possibly some solutions? [root@anistonetech zapata]# asterisk -f -d DEBUG[1024]: File config.c, Line 653 (__ast_load): Parsing /etc/asterisk/asterisk.conf DEBUG[1024]: File config.c, Line 653

I have a simple problem with sialing a SIP device. I'm SURE it's a syntax problem, but I dunno what it might be. Here are the debug messages: == Accepting call on 'Zap/1-1' ("PENSACOLA, FL" <8503846785>) -- Executing Goto("Zap/1-1", "2111|1") in new stack -- Goto (default,2111,1) -- Executing Dial("Zap/1-1",

Everyone, Just thought I would drop a line telling everyone here I have the software RxFAX/TxFAX up and running without any real problems. I did have to..... RH 9.0 1) Install an audio devel rpm 1) install libtiff from source, and copy over a bunch of include files to /usr/local/include 2) build/install spandsp 3) move app_rxfax.c and app_txfax.c to apps/ dir in asterisk source tree. 4)

Like most others on this list I also have some really annoying echo whenever a call goes out to the PSTN from a SIP phone... SNOM/Budgettone -> Asterisk -> X100P -> PSTN I have tried every echo canceler in the makefile and turned on and off aggressive suppressor etc. etc. etc. tried 32,16,128, and 256 bridgetaps and I can get it reduced to only a few seconds on the intro of the call and

Hi! I have some problem in my asterisk 1.4.2, I've installed it on centOS 5.2 and this didn't accept voip QoS and can't route the packets having voip QoS. So I should change voip packets to be routing with centOS. I want to use iproute2 but i don't what to do after installing iproute2. Anyone could help me please? -------------- next part -------------- An HTML attachment was

Hello, I'm searching for a router for our company. Does anybody has a suggestion for a router with a SIP Application Layer Gateway and good working QoS (Upstream AND Downstream). Regards Bastian

Hi, I'm looking for opinions on the "best value" router to use for home offices. It should work for a scenario in which there are 3 computers and 2 SIP phones, handling QoS so that the phones always have higher priority traffic than the PCs. (and not rely on the phones to do the QoS because some PCs may not be connected to the phones). QoS could be based on destination and source

Has anyone had any experience with the Dell PowerConnect 2724 Gigabit Switch and VoIP traffic? It seems to support Class of Service (CoS), but not full Quality of Service (QoS). Will CoS help prioritize VoIP traffic at all? I am setting up an asterisk PBX for 22 users with very light traffic, but I don't want to have the call start skipping just because someone is pulling a large

Hello all, Can anyone recommend a good book which thoroughly explains QoS from a Linux perspective? Something with TC examples & the like. I''ve looked at the following: http://www.amazon.com/gp/product/1580533418/qid=1148368189/sr=1-2/ref=sr_1_2/102-2819973-6353768?s=books&v=glance&n=283155 Engineering Internet QoS. Thanks.

Hi List Just a little bit OT, but then again perhaps an information that could be of great value for a lot of administrators !! Does anyone have experience with how to setup VoIP QoS for outgoing data through a Cisco PIX (515) ? I believe that it should be possible to give higher priority to outgoing VoIP packets. This is due to the problem of ADSL as the UpStream data rate is 1/4 of the

I have currently following the instructions at- http://www.voip-info.org/wiki/view/QoS+Cisco I am using a Cisco 877 router with an ADSL2+ connection. My upstream bandwidth is around 1Mbps, and my downstream around 4-5Mbps. I have two PSTN side interfaces - atm0 and dialer0 (dialer0 is where the ISP details are configured and the interface that the WAN side IP is applied on) Now which

Hi i want see if my QoS are good because i am not very sure ... the VoIP quality are not very good when i download. I have on my Linux routeur/Firewall Asterisk .. and i have into my config : ================================================ tcdevices: eth0 2000kbit 2000kbit tcclasses: eth0 1 100kbit 180kbit 1 tos=0x68/0xfc,tos=0xb8/0xfc eth0 2 full/4 full

Hello All, I am interested in QoS provided by Linux, when I looked into IP header I came accross ToS field, also while going more into detail about QoS I found that the QoS based on ToS is serviced thru DiffServ which in turn gives more priority to packets with higher value is ToS field, but I am not able to understand when we finally call dev->hard_start_xmit routine of underlying device

Does asterisk provide quality of service(QoS)? If it does, how do I use it? The reason why I ask is that I need to switch to use POTS should the internet connection becomes poor? Thanks, Jim

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, Is there any grapical interface for the QoS (Quality of Service) Traffic Control in Linux ? Greetings. - --- Carles Xavier Munyoz Baldó carles@descom.es Descom Consulting Telf: +34 965861024 Fax: +34 965861024 http://www.descom.es/ - --- -----BEGIN PGP SIGNATURE----- Version: PGP 6.5.8

We're trying to PQ (Priority Queue) packets on a Cisco using ACL's. What we're trying to avoid is hardcoding the IP address in the ACL. We were trying to match by TOS set by Asterisk however it seems we've run into a snag where the packet TOS tends to get reset somewhere on our network. Has anyone had this issue? We're running Cisco everywhere inbetween (even the switches). Is

It appears that while Linux has plenty of traffic shaping mechanism on transmit, there is nothing on receive side. While generally it does make sense since transmit is more CPU intensive operation, after all receive also consumes CPU cycles. It is clear that it''s best to drop the packet as soon as possible, i.e. on receive, if possible - by the driver itself. It may not be feasible in