similar to: centos4.2 -raid 1 and grub

Hi! Whew, I have googled around a lot w/this but can't quite seem to come up w/the right answer. This system works beautifully w/nothing wrong w/it. But my goal is to be able to test the raid system by just unplugging hda to mimic a faulty drive and have it just carry on and boot from hdc. md0 = hda1/hdc1 /boot (primary boot partitions on both drives) md1 = hda2/hdc2 / is it possible to

Greetings ... Been lurking on the list for some time, hoping that at some point, I might be able to add to the collective (Yes, way to much StarTrek in the background! ) ... I have learn quite a bit by just lurking, but now I think I might have something to add ... I'm not sure the exact protocol or procedure for this and it's late in the evening and would like get this out, before I

doing that grub-install /dev/sda will give me the "corresponding BIOS device" error. But now I fixed it by doing a manual grub install. first boot with cd1 and type linux rescue at the prompt when you're at the linux prompt after detecting and mounting the partitions, do a "chroot /mnt/sysimage" then # grub --batch #grub> root (hd0,0) Filesystem type is ext2fs,

On Wed, Aug 5, 2015 at 9:12 AM, Bowie Bailey <Bowie_Bailey at buc.com> wrote: > I am trying to upgrade my system from 500GB drives to 1TB. I'm going to guess that there are no IDE drives that have 4096 byte physical sectors, but it's worth confirming you don't have such a drive because the current partition scheme you've posted would be sub-optimal if it does have 4096

I never thought I'd say this, but I think it's easier to do this with GRUB 2. Anyway I did an installation to raid1's in CentOS 6's installer, which still uses GRUB legacy. I tested removing each of the two devices and it still boots. These are the commands in its log: : Running... ['/sbin/grub-install', '--just-copy'] : Running... ['/sbin/grub',

On 8/5/2015 12:34 PM, Chris Murphy wrote: > On Wed, Aug 5, 2015 at 9:12 AM, Bowie Bailey <Bowie_Bailey at buc.com> wrote: >> I am trying to upgrade my system from 500GB drives to 1TB. > I'm going to guess that there are no IDE drives that have 4096 byte > physical sectors, but it's worth confirming you don't have such a > drive because the current partition

I have a virtual machine that had been running fine using a RAW disk image (IDE). I am in the process of converting this virtual machine to use a single LVM and virtio. (For LVM backup snapshots and easy resizing purposes (no LVM within the guest)) I create the LVM and copied all the files from the existing RAW image to an ext3 under the LVM. However, I cannot get it to boot. It has to do

Hey I had the same problem some time ago. But here is a solution how to do that, but it''s a bit tricky! REQUIREMENT: THE SYSTEM PARTITION ON THE IMAGE MUST BE THE FIRST PARTITION, AFTER THAT THERE MUST BE ONLY SWAP PARTITIONS!!!! This setup would work, there should be no risk at all: Partition 1 on the image: / Partition 2 on the image: swap space This setup WONT''T WORK, YOU

Hi, I am trying to get my kickstart file that worked under 5.1 to work under 5.2 centos x86_64. This is the error that I get. On the screen it says Exception occured and gives me the option to save it. This is that file. I dont see any odd that would cause it to crash. Can anyone help. My kickstart file is in the mix below. Seems to be related to network, my line seems fine (I think) for

So I'm trying to RAID-1 this system which has two identical disks installed in it, and it isn't working for some reason. I started by doing a CentOS-4 install on /dev/sda1 as root, and with /dev/sda2 as my swap. I finish the install, yum update, and then I want to make the mirrors. I copy the partition table from one disk to the other: # sfdisk -d /dev/sda | sfdisk /dev/sdb I create

When I am install C6. I am getting an error about "A fatal error occurred when installing the cyrus-sasl package. Exit Installer. These are my packages: ls -l cyrus-* -rw-r--r-- 1 silentm silentm 11745776 Jul 3 00:08 cyrus-imapd-2.3.16-6.el6.x86_64.rpm -rw-r--r-- 1 silentm silentm 238380 Jul 3 00:03 cyrus-imapd-devel-2.3.16-6.el6.i686.rpm -rw-r--r-- 1 silentm silentm 237328 Jul 3

I am doing a kickstart install for CentOS 6.0 (x86_64 install) The error on screen is "fatal error occurred when install glibc package. Could indicate error with install media" When I looked at the /mnt/sysimage/root/install.log file I see Installing glibc-2.12.-1.7.el6.i686 error unpacking of archive failed on file /lib/ld-2.12.so;4e66d2ec cpio read failed bad file descriptor.

Any Virtualbox on CentOS guru's out there? I only have 1 VM on my linux host. in the update process to virtualbox 6.1.16 my config was lost. When I run Virtualbox my VM does not show. So I desire to add it back. My structure is this. ls -l /home/silentm/vmware/CentOS\ 64-bit\ LSI/ -rw------- 1 silentm silentm 8684 Aug 13 08:31 CentOS 64-bit LSI.nvram -rw-r--r-- 1 silentm silentm 0 Feb 27

Subject says it all. How can I get the 1.3 version and 0.9.28 to compile on CentOS 5.8 ??? When I compile the two as modules I get errors. My Makefile is: obj-m += 8139cp.o 8139too.o all: make -C /lib/modules/$(shell uname -r)/build M=$(PWD) modules clean: make -C /lib/modules/$(shell uname -r)/build M=$(PWD) clean The errors I get are: Entering directory

I am getting the following link error on centos 5 AMD 64 for opengl. What do I not have installed? I ran ./configure --x-libraries=/usr/lib --libdir=/usr/lib only warnings I got was abour FontForge missing. make depend make THanks, jerry ----------- make[2]: Leaving directory `/home/silentm/wine-0.9.40/dlls/wtsapi32' make[2]: Entering directory

On 1/30/2015 9:44 AM, John R Pierce wrote: > On 1/29/2015 7:21 PM, Jatin Davey wrote: >> [root at localhost ~]# lspci | grep RAID >> 05:00.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS-3 >> 3108 [Invader] (rev 02) > > to get info out of those, you need to install MegaCli64 from LSI > Logic, which has the ugliest command lines and output you've

CC [M] /home/silentm/MessageNet/digium/zaptel-1.4.10/kernel/wcte12xp/vpmadt032.o CC [M] /home/silentm/MessageNet/digium/zaptel-1.4.10/kernel/wcte12xp/GpakApi.o CC [M] /home/silentm/MessageNet/digium/zaptel-1.4.10/kernel/wcte12xp/../voicebus.o LD [M] /home/silentm/MessageNet/digium/zaptel-1.4.10/kernel/wcte12xp/wcte12xp.o

Hi all, I need to compile alsa-project 1.0.16 on the latest centos 5.1 kernel. I am getting this error. What to do... ? CC [M] /home/silentm/MessageNet/alsa-project/alsa-driver-1.0.16/acore/sound_oss.o CC [M] /home/silentm/MessageNet/alsa-project/alsa-driver-1.0.16/acore/info_oss.o In file included from

I have read the info on apache 2.4... I added to the bottom of httpd.conf these lines (and restarted httpd) ------------------------- <Directory /var/www/html> # old 2.2 config # Order Allow,Deny # Allow from all AllowOverride None Require all granted </Directory> <Directory /home/silentm/public_html/gifs> AllowOverride None Require all granted </Directory>

Dear CentOS users, I installed CentOS 6.2 x64 in a Sun Fire X4450 machine, it has 4 disks and I configured them to be a single volume (no RAID). The installer sees the volume perfectly, its 570Gb. I created two ext3 partitions, /dev/sda1 and /dev/sda2. In the logs I see they are formated correctly. All the files are installed. Then when I reboot, I get to the GRUB menu. Choose the first and only