similar to: port-forwarding problem!?

Hi all, I'm using openssh-2.9p2 on Solaris 2.8. I can get remote port forwarding to work using the -R flag, but only with ssh protocol 1 not ssh protocol 2. I've read that remote forwarding protocol 2 was not supported in earlier versions of openssh, but I'm wondering if this is still the case. Jarno Huuskonen [Jarno.Huuskonen at uku.fi], posted a patch in 2000 to add support for

Hi, It looks like remote forwarding with SSH v2 is not working on my Solaris machines (and from what I understand from the source, it may not work elsewhere either). When looking at channel_post_port_listener() in channels.c, I found that nextstate was defined as : nextstate = (c->host_port == 0) ? SSH_CHANNEL_DYNAMIC : SSH_CHANNEL_OPENING; And later comes the call : if

Hi all, This is a client side only implementation of reversed dynamic (SOCKS) TCP forwarding, which means it is compatible with any existing servers have 'remote forward' capability. To establish such forward, use "ssh -R [BIND_ADDRESS:]PORT ...". The server will listen on that port and address and accept SOCKS traffics. Hope this will be useful for you. There was an

Hello, I'm running OpenBSD 2.9 (-rOPENBSD_2_9) on i386. Remote port forwarding doesn't work. Attached are 2 logs of ssh -v -R2828:localhost:22 localhost and sshd -p 2222 -d Note that server tries to forward to Connection to port 2828 forwarding to 0.0.0.0 port 0 requested. instead of localhost port 22 as it should. what ssh, what sshd and /etc/sshd_config are also attached. Thanks

Hello, Today I tried using "dynamically assigned" port for remote listener, by requesting listener on port 0. This is supposed to create a listener on a port choosen by server. Everything seemed OK (the choosen port was sent back to client), but forwarding was refused. So I checked the source. in channels.c, function: channel_setup_fwd_listener /* *

Hi ! Here's a patch to add remote port forwarding support (protocol 2) for openssh. I have tried to test that it works like it should but a more thorough testing is needed. This patch adds both client/server support. The patch should be applied to openssh-2.1.1p4 source tree. Also included is a PortForwarding sshd_config option, new ./configure option --disable-forwarding that should make it

I know that there was a discussion on this about a year back, and there is a bug 556 this week that mentions TCP_NODELAY. However, when I use ssh through a pipe (e.g., to tunnel through an HTTP proxy using CONNECT) I see: getsockopt TCP_NODELAY: Socket operation on non-socket How do I tell which end is generating this (I'm assuming the local side, which is running through the pipe). Also,

this (uncomplete) patch makes various features compile time options and saves up to 24K in the resulting ssh/sshd binaries. i don't know whether this should be added to the CVS since it makes the code less readable. perhaps WITH_COMPRESSION should be added, since it removes the dependency on libz -m Index: Makefile.inc =================================================================== RCS

Can't seem to find the answer anywhere... I'm currently using an rsync script on the source box to transfer some individual files to the destination box...all works well. The script: rsync -e ssh \ /var/qmail/control/file1 \ /var/qmail/control/file2 \ /var/qmail/control/file3 \ /var/qmail/control/file4 \ destination-box.xxxxx.com:/var/qmail/control Now, instead of "pushing"

Hello all, I was told on IRC that I should come here to discuss a recommended change on the networking page in the wiki. If you take a look at the "Basic Script" shown here: http://wiki.libvirt.org/page/Networking#Forwarding_Incoming_Connections It does two things: 1) Create a DNAT rule in the NAT table of IPTABLES 2) Create a FORWARD rule in the FILTER table of IPTABLES The FORWARD

Hi all, currently I am considering writing a patch for OpenSSH that will allow portforwarding using the control_master unix domain socket. The idea is to introduce an extra SSHMUX command, SSHMUX_COMMAND_SOCKS, which will then pass control to the normal socks functions used for dynamic forwarding. The main reason for me to write this patch are: - some more control over who gets to connect to

On 06/08/2015 02:43 PM, Laine Stump wrote: >> However, if I changed the destination address from "anywhere" to the >> IP of the host machine, the problem resolved. So I change the script >> to as follows. (Changes are highlighted. For some reason the original >> script didn't work using /bin/sh, but it did with /bin/bash, so I >> changed that too). >

Hello all, I’m currently trying to figure out how to forward ports to guests that are on a NAT Network. I have followed the directions on https://wiki.libvirt.org/page/Networking under the “Forwarding Incoming Connections” Section and get connection refused when attempting to connect. System: Ubuntu Server 18.04.1 Virsh / LibVirtd Version: 4.0.0 Here’s the contents of /etc/libvirt/hooks/qemu  

I am running OpenSSH 2.9p1 on SunOS 5.7 w/4-24-2001 patch cluster. Like many other users I am seeing the hanging session on logout with background processes. This is a huge problem for me as I centrally manage 50+ machines with rdist across ssh. Instead of just complaining about the problem I thought I would put my CS degree to use and try to track down the problem myself. For starters,

FINALLY, it's here. You can now tell SSH which address to bind to for every single port forwarding option! This patch allows you to pass the following as ssh command line options: ssh -L 192.168.1.55:1234:localhost:80 -R ::11:22:aa:bb/80/localhost/80 etc. Or as normal config file options: LocalForward ::11:22:33/1234 localhost/80 RemoteForward 1.2.3.4:80 localhost:80 It will also

I'm using: % ssh -V SSH Version OpenSSH-1.2.3, protocol version 1.5. Compiled with SSL. % uname -a Linux gellar 2.2.13 #1 SMP Wed Dec 29 14:07:41 PST 1999 i686 unknown and am wondering whether it's a fundamental shortcoming of the SSH protocol that argument splitting is not preserved from client to server, but instead the argument list is re-split on whitespace. E.g., from my machine

I am enclosing a context diff of the changes that I made to get openssh working on UWIN. UWIN is a UNIX operating system layer that runs on Win32 systems. For more information on UWIN go to http://www.research.att.com/sw/tools/uwin/. I also ran configure using -with-cppflags=-D_BSDCOMP=2. I don't know where that information would go with the source code. Let me know if you need more

https://bugzilla.mindrot.org/show_bug.cgi?id=2079 Bug ID: 2079 Summary: openssh 6.1/6.2 disconnect due to channel bug Classification: Unclassified Product: Portable OpenSSH Version: 6.1p1 Hardware: amd64 OS: FreeBSD Status: NEW Severity: normal Priority: P5 Component: ssh

Hi all, I'm very new in this list, as looking for codes to plug up the lack of functionality of "Protocol 2 Remote Forwardig". Fortunately, I could find it in MARC's archive. Mr. Jarno Huuskonen posted the codes in Sept, last year, and I tried applying it to my FreeBSD box environment. I couldn't apply an original patch, of course, for incompatibility of virsion. The