similar to: p2p?

Hi, I have a CentOS 5.2 desktop with the RPMForge repo enabled. I just ran 'yum update', and there seems to be some trouble with the wxGTK apps. A simple 'yum update' gives this error message: --8<-------------------------------------------------------------------- --> Finished Dependency Resolution Error: Missing Dependency: libwx_gtk2u_adv-2.6.so.0 is needed by package

Hi, I have met the problem: when I use the shaping discipline tc qdisc add dev ppp0 parent 1:2 tbf latency 50ms burst 1450 rate 50kbit one of my application (namely, "aMule") starts leaving sockets in "CLOSING" state. These sockets accumulate and do not disappear. Eventually I have so many of these dead sockets that the kernel warns "Out of socket memory" in

Hi all, I'm trying to use centos5 as desktop/development machine, but i having a lot of problems to compile Amule and d4X, tools that I use a lot. Somebody have some experience to do this work?? sombody have an .spec file?? thanks a lot ! JC J?nior Ps. yes I have all lib neccessari to build this tools.

I execute emule 0.47c (because Amule and mldonkey doesn't have protocol ofuscation support) but I have some problems: 1.- I import the incoming + temp directories from amule, 250 downloads inside => error too many open files. To solve this, I try to import 20 files, next 20 files more, next 20 files more, in batch process. 2.- But when I use emule, the same error appears in some files in

Hi peploe, i am new in the list, i need know, how blocked the Amule/emule in shorewall? My dist. debian version: 3.2.6-shorewall -- .~. / v \ Seja Livre, use GNU/Linux! /( )\ ^^-^^ ------------------------------------------------------------------------- This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2005.

Hi! I don;t know what i am doing wrong because i have still Low ID on aMule. I have action.AllowaMule and accept tcp 4662:4771 and udp 4672. Thanks, Mitja

Hi all... I have configure a Shorewall gateway to my little lan im my home. The shorewall work fine here... However, when I try to use Limewire, I can download nothing.... On fact, I can''t get any high connection on Limewire.. What can I do to make Limewire work properly behind a Shorewall gateway???? May be I have to open all port (both tcp and udp), but how? Thanks a lot... Best

I have been running WinMX for a while on Wine, and while it has a few quirks, it works (for the most part) quite well. eMule, OTOH, flat refuses to start and throws an unhandled exception: page fault... Has anyone here had any luck running other P2P programs via wine?

We''ve just upgraded to a new firewall machine, and a new version of Shorewall. We''re now on 2.04; previous version was 1.3.9b (!). So I''m pretty sure whatever problems we''re having are related to the big version jump. We''re using config files that exactly match our old (working) configuration (IOW, these are things which _were_ working on the old

Hi I believe that whole question is in topic. Is there any way to recognize ( and then shape ) p2p traffic which is encrypted? Modern p2p clients have this ability moreover some of them have this enabled by default. Now I''m using ipp2p for iptables but as I know this doesn''t recognize encrypted traffic. Thanks in advance. Pozdrawiam Szymon Turkiewicz

Hi all, I''m tring to isolate P2P traffic, specifically BitTorrent, for my QoS scripts. I can''t seem to completely isolate ALL BitTorrent traffic. I identify & mark packets and then use tc filters to put them into appropriate classes. My firewall rules (below) do the markings. My VoIP boxes'' and ICMP traffic get highest priority (mark 1). Then comes DNS, SSH,

Dear All I have added the following line to /etc/shorewall/rules: ACCEPT net fw tcp 4662 However, the program aMule continues to give me the following error: NG : Your 4662 port is not reachable. Any further ideas? Thanks in advance, Paul

Hi, My home setup is as following: - 1024/128 kbit ADSL - FC3 I set up HTB to prioritize traffic. I am not very pleased with the obtained results. The scope of my setup is to have some ssh sessions with remote servers while browsing websites and running aMule Nothing complicated (I think... ;). The very high priority traffic (ssh), gets stuck when I start aMule and make an FTP download.

I have an old Pentium 233 MHz with 256 MB RAM that has Debian and wine20041019 installed. As this machine runs "not so fast" I'm not sure if I should upgrade to 0.9. If one of you could tell me that 0.9 runs a little bit faster than 20041019 this would ease my decision. ;-) Markus Winhard

Wine 1.0-rc1 not able to install: 1. internet explorer 6 & 7 programs not running et-all after installation: 1. sony ericsson pc suite 2. sony ericsson software update 3. limewire Kindly help! [Crying or Very sad]

I am still fighting with this issue. I did the following: I connected to the NAS with a read-only account called kodi. I traversed various folders and I finally opened an image. Everything went fine. Looking at the logs, the get_entry mask file only shows the final folder: smbd_dirptr_get_entry mask=[Anhelina Viber] found Users/luca/Pictures/Canon/Alessandro/Amici/Anhelina Viber fname=Anhelina

I recompiled yet 2.6.19.1 kernel (using iptables with the same patches too). The configuration for this test is: 1) linux box with 2.6.19.1 kernel (SMP machine) with these patches/modules: a) l7-filter b) ipp2p c) connlimit d) set 2) 4 ethernet interfaces: a) 2 external (eth1 and eth3) interfaces with balanced links (as described in nato-howto) bridged as wan0

I could find the amule package in CertOS7, is anyone know this? Thanks. Xiaoqi

Clean install of Slackware 10.2. Wine 0.9.20. Downloaded slackware package. Installed with KPackage via KDE, no errors. I have several Windows apps that I used under Wine with Slackware 10.0. I right click on executable, select Wine Windows Emulator, I can see in the process table Wineserver, wine-preloader, and wineprefixcreator(?). Then they all go away, and nothing happens. It doesn't

Hi, I run Centos 4. I can't add users using the adduser command, I get this error: adduser: cannot rewrite shadow password file I can't change the users passwords with passwd, I get this error: passwd: Authentication token manipulation error What is wrong? Thank you Samuel