similar to: USB Problem

Hi Friends, I have an Excalibur 4GB USB Pen Drive Model Number EXC4. I think it is getting detected by the Centos but I am not sure about the mount point or the device point it is taking /dev/s?? Logs from /var/log/messages. Mar 11 11:30:06 l_l_box kernel: usb 1-1: USB disconnect, address 3 Mar 11 11:30:22 l_l_box kernel: usb 1-1: new high speed USB device using address 4 Mar 11 11:30:22

--zhXaljGHf11kAtnf Content-Type: text/plain; charset=us-ascii Content-Disposition: inline Content-Transfer-Encoding: quoted-printable I'm trying to set up a TrippLite Internet Office 750 just like this guy: http://lists.alioth.debian.org/pipermail/nut-upsuser/2005-June/000007.html Here's the output of a few interesting commands stuart@tyro:~+ dpkg-query -l nut nut-usb| tail -n2| awk

I have a MGE Evolution 3000 connected via USB to a linux server (HP Proliant G3). The server is running kernel 2.4.30 and nut-2.0.3. But before nut trying to connect to the UPS, I guess HID doesn't work as long as I get a message like this in dmesg: -------------------------------------------------- usb.c: new device strings: Mfr=4, Product=136, SerialNumber=50 usb.c: USB device number 2

Hi. Is the subject UPS model supported? I believe so, but I don't have a unit to test with. Any comments on this model? I'm trying to advise a colleague. Thank you, as always. T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=051d ProdID=0003 Rev= 1.06 S: Manufacturer=American Power

Hi, I have plug in this USB network device: > Bus 001 Device 002: ID 2001:1a02 D-Link Corp. > T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 > D: Ver= 2.00 Cls=ff(vend.) Sub=ff Prot=00 MxPS=64 #Cfgs= 1 > P: Vendor=2001 ProdID=1a02 Rev= 0.01 > S: Manufacturer=D-Link > S: Product=DUB-E100 > S: SerialNumber=E5ECEB > C:* #Ifs= 1 Cfg#= 1

i can't seem to get newhidups to detect my UPS.. i'm using nut-2.0.3 (tried both the rpm from fc5-updates and compiling my own) here is the entry for the UPS in /proc/bus/usb/devices T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0764 ProdID=0501 Rev= 0.01 S: Manufacturer=CPS S: Product=UPS

Hi I am trying to connect a reliance netconnect data card on my linux box ( cent os ) , i am able to the detect the device /dev/ttyUSB0 these are the following steps I did : Check your card is recognized by the kernel # cat /proc/bus/usb/devices ..... ..... T: Bus=07 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 11 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P:

- UPS MGE Premium Ellipse Premium 1200 - SuSE Linux 10.0 OSS, kernel 2.6.13 smp - gcc version 4.0.2 20050901 (prerelease), glibc-2.3.5-40 - mgeups-psp-3.0.0-3, nut-2.0.2-4 - Dell Dimension 8400 with dual core Intel Xeon. 3.0GHz. lsusb shows: Bus 002 Device 003: ID 0463:ffff MGE UPS Systems UPS less /proc/bus/usb/devices shows for bus 2 device 3: T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=

Hi, I'm trying to get a Powerware 3105 UPS working on SuSE 10.0. I have compiled nut from the current Subversion repository. This UPS uses the bcmxcp_usb driver. I cannot get the driver to find the ups on the USB bus. The error message I get is:- -------------- bcmxcp_usb -u nut -DDDDD -a pw3105 -------------------- Network UPS Tools - BCMXCP UPS driver 0.10 (2.1.0) debug level is

Howdy nut-users :) Got a problem with nut detecting my UPS. Here's my scenario. Base platform is a HP ML350 G6. UPS is an APC Smart-UPS 1000. Base OS is VMware ESXi 5.0 with all current patches. I've created a virtual machine using the VMWare supplied VMA. USB passthrough is configured to pass the UPS through to the VMA. So I essentially have a SLES 11 (x86_64) server with a USB

Hi, I have a Liebert POWERSURE PSP connected via USB. Cleanly built and installed from source nut-2.4.3.tar.gz using kernel 2.6.30.5 #cat /proc/bus/usb T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=10af ProdID=0003 Rev= 0.00 S: Manufacturer=Liebert S: Product=Liebert PSP 350 FW: 02 S:

... T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 5 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=06da ProdID=0002 Rev= 1.00 S: Manufacturer=Powerware S: Product=Powerware UPS C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 60mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=usbfs E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=20ms ... Should the kernel

Hello, i have this strange problem with APC BackUPS RS 1500 ? older one model, white one under windows in powerchute is device OK, working everything ok selftest ok, just ordinary ups. under CentOS 7 minimal (CentOS-7-x86_64-Minimal-1708.iso) kernel version 3.10.0-693.el7.x68_64 driver version 2.7.2 i have this strange probem: nut driver didnt start automatically with error, after i enter in

Hello, i have this strange problem with APC BackUPS RS 1500 ? older one model, white one under windows in powerchute is device OK, working everything ok selftest ok, just ordinary ups. under CentOS 7 minimal (CentOS-7-x86_64-Minimal-1708.iso) kernel version 3.10.0-693.el7.x68_64 driver version 2.7.2 i have this strange probem: nut driver didnt start automatically with error, after i enter in

Hi, I'm new to NUT. I've installed Fedora 8 and NUt along with it. I'm now having a go at getting my Unitek Alpha 1200sx UPS to work and shutdown the box automatically. I know this isn't officially supported but I'm trying my luck... I've seen that other Unitek UPSs use the 'megatec' driver however I'm unsure whether this will do the trick. My UPS comes with a

Hello I've got an Unitek UPS (650ipE) that use megatec driver ... I'm running Ubuntu 7.04 with a 2.6.20 kernel and nut 2.0.5-1 package Ubuntu by default use Udev and "hid", "usbhid", "evdev" kernel modules are loaded automatically The UPS is detected on system level but "upsdrvctl" can't access to the device ... Does anyone could give

I used a brazilian UPS from "TS-Shara" which uses the megatec serial protocol and it works perfectly. Now I have another one from the same brand (TS-Shara) and it uses a USB cable. I found the following: T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0483 ProdID=0035 Rev= 2.00 S:

Hi all, I just downloaded, built and installed nut-2.0.4-pre2. I have an APC Smart ups 3000 connected via a usb cable. I have compiled and installed the usb drivers. I installed the libhidups and libhid.usermap per the README. I have the following ups.conf: [APC-3000-ups] driver = newhidups port = auto desc = "APC smart 3000" When I try to start the driver I get the

i just purchased a tripp lite OMNIVS1500XL and have been attempting to get it working with the usb drivers since it doesn't have a serial port. it hasn't been anywhere near successful and i was hoping someone might be able to point me in the right direction. i run gentoo and this is what i currenlty have installed: nut 2.0.2 libusb 0.1.10a (gentoo modified) usbutils 0.11-r5

Folks, I'm fairly new to this whole Linux UPS thingie, but I'd quite like to have a look at getting my UPS to work under Linux and would be grateful for any help in getting a driver. I have a reasonable working knowledge of Linux and software development, and thus am happy to modify config files, alter kernel settings, etc, although I'm no C guru. I have a Kebo UPS-650D, which