similar to: Custom com32

Hi, I've checked the archives for my issue, and while there is relevant discussion, the problem the original poster was asking about didn't seem to have been resolved then either (~2 years ago). At any rate, basically what I'm trying to do is send (possibly receive) UDP packets via the PXE stack using the com32 API (using version 3.11 of syslinux). I have followed both the comboot

(sorry for my english if it is approximate !) I want to access harddisk from com32 api with PXELINUX. I try to use int 13h Extended Read Drive Parameters (48h), it doesn't works. Here is my code, I have an error 1 in AH return code. Int 13h Read Drive Parameters (08h) work well. ******************************************************************************************* struct params {

Hi everyone. I've read through the archives and found a few posts about using the PXE stack, but none of these really helped me. What i want to do is: Prompt the user for 2 values, desired hostname and a "pin" (just a number) and send this information over UDP to my server The problem is not the user input but the UDP part. I've tried to change the code from the post of jesse

Here is a partial patch that I'm using to illustrate a few questions that I have. Looking at the gpllib write_sectors (com32/gpllib/disk/write.c) it looks like the allocated size is wrong; size is in sectors so we should adjust the alloc/memcpy by size*SECTOR. Also, comparing core/diskio.c it looks like the registers aren't even setup right. In the patch below I put an #if 0 around the

Does the COMBOOT stuff with 2.04 work correctly with function calls? or does one need to write it as one huge function? If memory serves me correctly, there was some problem if hello.c was modified to include additional functions, in an earlier version. - Murali

Hey, Looks like read disk function which was launched in 3.35 isnt working. Did anyone test this on any hardware? I'm using it thru the com32 interface to read contents of the active partition of a USB boot key (syslinux). I did a sample test like: void scanAndPrint() { com32sys_t regs_in; char *sectorBuf = __com32.cs_bounce; int i; memset(sectorBuf, 0x0, 512); // XXX MARK 1

Hi, Hopefully you someone can tell me what I'm doing wrong. First, the code. I placed this at the bottom of the main loop in com32/modules/disk.c as a simple test of writing to the disk: printf(" Host bus: %s, Interface type: %s\n\n", d->edd_params.host_bus_type, d->edd_params.interface_type); zero_buf = calloc(1, d->edd_params.bytes_per_sector); for(int

TBAA Question. Please consider the following test case. ---Snip-- struct B { int b1; int b2; }; struct C { int b1; }; struct A { int a1; struct C SC; int a2; }; int foo1(struct A * Aptr, struct B* Bptr) { int *a = &Aptr->SC.b1; *a=10; Bptr->b1 = 11; return *a; } int foo2(struct A * Aptr, struct B* Bptr) { Aptr->SC.b1=10; Bptr->b1 = 11; return

From: Matt Fleming <matt.fleming at intel.com> Since we can't use __intcall() for EFI, and since we can now have the ELF module code resolve all our symbols at runtime, we should delete as many references to __intcall() as possible and just access the symbols directly. The most interesting patch is the support for weak symbols. We need to be able to reference derivative-specific

I'm seeing this on a HP Blade and i'm not sure why this is happning since the nature of the issue is so wierd. I compiled mboot.c with a DEBUG defined in the mboot.c file. In the funciton init_mmap(), it prints the e820 map and on the HP blade this map values come out to be totally random. Some weird numbers which dont make any sense at all. However, if i add a while(1); or a exit(1); at

Hi : Is it possible to replace bios interrupt with a com32 program? Louis Best Regards!

Hi folks, Syslinux 5.00 is out in time for the holidays. This release includes a lot of changes from 4.06. I've included the NEWS entries below, which highlight the major changes. Lots of assembly code has been rewritten in C, which makes further development much easier (and also really helped for the 'firmware' abstraction that appears in Syslinux-6.00-pre1). So be on the lookout

Hi, OK. I tried your suggestion. I modified the dovecot config file "10-logging.conf", like so: log_path = syslog and mail_debug = yes It appears that the logging goes to "/var/log/maillog", not "messages" as I expected. Restarting service dovecot produces info in the "maillog" file showing the restart: ... Jan 22 15:20:14 coe dovecot: imap: Server

Hi, I have a question. I have dovecot 2.0.9 running on a CentOS 6.6 email server for a small department, ~15 users. amavis and postfix are also enabled. It appears that amavis invokes spamassassin, which tags incoming spam email. All email is then put into users local inbox directory, regardless of spam tag X-Spam_Flag value of YES or NO. I want instead to redirect spam to a special directory.

Hi Tom, Matt, I'm running into strange issues with the cos test (piglit generated_tests/cl/builtin/math/builtin-float-cos-1.0.generated.c) I have been seeing random failures (incorrect results) for some time and tried to investigate. the weird part is that the failures are not 100% reproducible, sometimes the tests pass, or partly pass (it's usually float8 and float16 subtests that

Hi Peter, Please pull the following changes. Paulo, I had to revert your "pxe: resolve names via DNS from protected-mode code" change because dns_resolv() is only implemented for PXELINUX and causes undefined symbol references for ISOLINUX, etc. Feel free to make the change again on top of the revert. The following changes since commit e7bd19def830e8341b1a100956345f1028740b9e:

Hi Peter Anvin I tried to use open file and read file SYSLINUX API. But it always make my PC104 freeze. My snip code : ================================================ int __start(void) { int ax,cx,dx,es,si,di,t; com32sys_t inreg,outreg; memset(&inreg, 0, sizeof inreg); memset(&outreg, 0, sizeof outreg); strcopy(__com32.cs_bounce, "test.txt"); inreg.eax.w[0] = 0x0006; //

# HG changeset patch # User George Dunlap <george.dunlap@eu.citrix.com> # Date 1337961666 0 # Node ID 1c28051020488782f1277dd60a2418324580297e # Parent 69c3ae25bb1ddcb0ea44b7566d36d34e9d6a70aa libxl: When checking BDF of existing slots, function should be decimal, not hex Spotted-by: Konrad Wilk <konrad.wilk@oracle.com> Signed-off-by: George Dunlap <george.dunlap@eu.citrix.com>

I want the curve to touch the y axis like the curve touches the upper boundary. How can I eliminate the margin between axis and curve on the left side? x1 <- c(1,2,3,4,5) x2 <- c(2,4,6,8,10) mod <- lm (x2~x1) hm <- function (x) (mod$coe[1]+x*mod$coe[2]) plot.new() # ... box() curve (hm,lty=1,add=T,xaxs="i",yaxs="i") (R 2.8.1) -- Sensationsangebot verl?ngert: GMX

Hello, I have installed GlusterFS one month ago, and replication have many issues : First of all, our infrastructure, 2 storage array of 8Tb in replication mode... We have our backups file on this arrays, so 6Tb of datas. I want replicate datas on the second storrage array, so, i use this command : # gluster volume rebalance REP_SVG migrate-data start And gluster start to replicate, in 2 weeks