similar to: How to get the /proc/parport????

Okay, spending the time to dot t's and cross i's (or something like that), I think I have something now that can be called 3.00-worthy, so let's call it a release candidate. Changes over the earlier 3.00 prereleases: - -m and -a options now supported by the DOS installer. - PXELINUX now allows IP addresses, FQDNs, and truncated hostnames when specifying an alternate TFTP server

Hello, Can I load setupldr.bin directly using isolinux without original CD boot sector? Thanks, Theewara

perhaps the boot-from-cdrom code in Smart Boot Manager? Bernd >>> No, since booting from CD-ROM requires that the El Torito part of the BIOS is activated, which it won't be if it didn't boot from CD-ROM in the first place. ---------------------------------------------------------------- Op deze e-mail zijn de volgende voorwaarden van toepassing:

I have a Lilo.conf file, which I have tried for many hours to convert to Syslinux. I looked around on the web for references on translating some of the components. I want to convert it to Syslinux/Isolinux. Any suggestions would be greatly appreciated. When I tried to convert it I made sure that the kernel and initrd had proper DOS names and such. -Michael =:LILO.CONF:= prompt timeout=10

I'd like to take advantage of the small, compressed Linux systems such as Knoppix or BeatrIX, but I can't have a CD rom on my system. (A project's marketing requirement.). So I figure I could use something like SYSLINUX or ISOLINUX to do it for me, but there is some magic in the process (the sequence of booting) that eludes me. 1/ mbr (from SYSLINUX) installed on hard drive... and

isolinux: Extremely broken BIOS detected Yoper 2.1 --------- ISOLINUX 2.11 2004-08-16 isolinux: Loading spec packet failed, trying to wing it... isolinux: Extremely broken BIOS detected, last ditch attempt with drive = 9F isolinux: Disk error 01, AX = 4209, drive 9F Boot failed: press a key to retry... Helix 1.5 --------- ISOLINUX 2.04 (Debian, 2003-06-06) isolinux: Loading spec packet failed,

hi there, hope this is not too much out of topic here... i give it a try anyway :-) when i try to build the iso with: mkisofs i get the following error: [...] Using TTYX2000.;1 for ./dev/ttyX2 (ttyx2) Using TTYS0000.;1 for ./dev/ttys0 (ttyS0) Using TTYY3000.;1 for ./dev/ttyY3 (ttyy3) Using FD0H360000.;1 for ./dev/fd0H360 (fd0h360) Using TTYX1000.;1 for ./dev/ttyx1 (ttyX1) Size of boot

HPA, a longterm reminder. See below. Can you also make a LABEL ignore other labels if no KERNEL statement is found in between? That way you could define multiple aliasses for an entry. label foo label bar label memtest kernel memtestp foo ignores 'label bar' , 'label memtest' and executes 'kernel memtest' bar ignores 'label memtest' and executes 'kernel

I have just released SYSLINUX 3.00-pre9. The only change versus 3.00-pre8 is that the MEMDISK query API now reports the boot loader ID byte, per Bernd's suggestion. This is a release candidate, and I plan to release it as 3.00 *tomorrow*, unless I hear back anything bad. -hpa

Hi! H. Peter Anvin, Could memdisk be made readonly? Thanks a lot! Anticipating your reply. _______________________________ Do you Yahoo!? Declare Yourself - Register online to vote today! http://vote.yahoo.com

Hi, I am trying to boot a liveCD thats on my hard disc ...is there a way of doing this using lilo ? reason well rather than keep burning to CD then testing I want to be able to make changes then test by booting to liveCD.... Thanks in advance Dave T..

Hello! I'm trying to boot with a remastered Knoppix 3.4 CD. I burned it with debugging and I get the following output: isolinux: Starting up, DL = 9F isolinux: Loaded spec packet OK, drive = 9F isolinux: Loading main image from LBA = DEADBEF0 isolinux: Sectors to load = D5B7 isolinux: Disk error BE, AX = 42F0, drive 9F A don't understand everything in it and I can't find enough

Hi All, I was testing syslinux floppy on a Mazza MotherBoard, his chipset is VIA MVP3 (VT82C598MVP, VT82C586B), and Winbond W83877F/TF. After reading the floppy, I see 'boot failed', I have to ide disk in the system, only flash device. I used the -s option to build the floppy. Does Somebody know if the chipset is supported? I tested the floppy on toshiba laptop and it works very fine.

I have been asked to build a Linux Installation lab. The lab has to support the installation of SUSE Enterprise 8, Red Hat (Industrial strength), Fedora, Debian and Mandrake and probably a couple of others. Here is the catch: 1. The machine(s) will only have a virtual floppy attached so installation will be via network (we?ll supply the mirror). 2. It must be completely automatic ? one floppy

Hi, I am trying for quite some time to create a bootable hd disk image with mkdiskimage (included in the syslinux distribution) and the combination isolinux/memdisk. It just won't work:-} I have done the following: [snip] # ./mkdiskimage -d -o disk 256 32 1 640 # losetup -o 640 /dev/loop3 disk # mount /dev/loop3 /mnt/3 # mount | grep loop3 /dev/loop3 on /mnt/3 type vfat (rw) :: copy

Hi all, I'm trying to work out how to boot DOS on a diskless PC, and I've come to a bit of a stumbling block with loading IPX support (which is extremely important, since most DOS games use IPX for network play ;-)) So far thanks to PXELinux and Memdisk I've gotten a DOS floppy image booting successfully, but I'm stuck trying to get IPX support. Admittedly I don't have much

HOPEFULLY fixes the 3.05 initrd bug. Please try it out and confirm; I will try to release it as 3.06 tomorrow. SIGH... -hpa

I have a 32MB HD image that I can pxelinux.0/memdisk boot without issue. I would like to both memdisk and my image on a CD and then boot from the CD with pxelinux.0. Is this possible? If so how? Thanks.

Does anyone have an idea how to fix this problem. When installing from floppy, it appears that everything installs correctly to hda1. I can see all the files that get installed on hda1 when mounting it. However, after I change the boot options to boot from hard disk I get the above error. I have never had this problem before, it usually installs very fast and painless. The only difference this

Hello! I would like to add the syslinux mailing list to gmane.org so I can read it with my newsreader (I think it is more convenient). Is that ok? For more information go to http://www.gmane.org/ Cheers Alex