similar to: tftpd-hpa filename remapping

Hi mailing list, I'm working on PXE booting a BartPE (=Windows XP) system from a server running hpa tftpd. In the initialization phase the files are requested from the boot server by TFTP, later the transfer is switched to SMB. Most of the problems during this tftp phase can be solved with the remapping feature quite nicely like: *converting filenames into absolute paths *convert

I have spent the last two hours on this issue. I think there's a problem with tftp-hpa. Setup: attempting to use Debian FAI, but there is definitely a problem with PXELINUX. pxelinux.0 is obviously being loaded by clients, but *nothing* in the pxelinux.cfg directory can be loaded. Clients sit and spin on their MAC files and when they get to default nothing happens. This is

On Sun, Jan 29, 2017 at 12:09:43PM +0100, Uwe Kleine-K?nig wrote: > AI_CANONNAME is only relevant when the resulting official name is used, > which is not the case in tftpd for the address to bind to. Also > AI_ADDRCONFIG isn't helpful. This flag is good for sockets used to > connect(2) somewhere. But for listening sockets it makes tftpd fail to > start when -a 0.0.0.0:69 is

Hello, I need help in setting up tftpd-hpa to send a kernel to a client, on a debian woody installation. I did manage the feat when using tftpd to send a kernel to a client which had a separate network interface card, but I would like to do it with integrated LAN. Trials with tftpd failed with error messages starting with 'PXE', and later I learned that tftpd-hpa is needed for the PXE

This is more a question than a serious proposal. The name of the pid file should probably be configurable, and it should be unlinked on normal termination, but no such thing exists in standalone mode. SIGTERM and SIGINT should be catched and considered normal, I guess. Signed-off-by: Ferenc Wagner <wferi at niif.hu> --- tftpd/tftpd.c | 7 +++++++ 1 files changed, 7 insertions(+), 0

Op 2013-08-26 om 09:35 schreef John McDonnell: > On Behalf Of Geert Stappers > Sent: Sunday, August 25, 2013 6:42 AM > > > > On my previous TFTP server I had logging. I did see all requests > > in logfiles. > > > > On my current TFTP server I have also added the options '-v -v -v', > > but no logging. At least I can't find it them in

I believe I have encountered a problem with tftpd-hpa very similar to the problem described in the following link: http://syslinux.zytor.com/archives/2003-May/001955.html We were running tftpd-hpa version 0.29 on RedHat 8.0 (on an older Dell desktop), and upgraded to tftpd-hpa version 0.42 when the problem was discovered; however, we are seeing the same thing after the upgrade. The TFTP

On 07/29/2015 01:45 AM, Ron via Syslinux wrote: > > Take 2 at bouncing this to the rest of the original recipients through a > different MTA, since mail.zytor.com refused to accept it the first time. > > Please re-add Jason Gunthorpe <jgg at obsidianresearch.com> and > 793921 at bugs.debian.org to the CC for replies. > > > On Wed, Jul 29, 2015 at 05:34:00PM

If I omit --secure from the tftpd-hpa command line, I then need to e.g. `tftp -c get /var/lib/tftpboot/vmlinuz` instead of plain /vmlinuz, even though I pass /var/lib/tftpboot as the tftp dir in the tftpd-hpa command line. That essentially means that I'm exporting my whole /, which is clearly something I don't want to do. I basically want tftpd-hpa to serve files from /var/lib/tftpboot

On Thu, 2014-01-30 at 11:25 -0500, Dan Swartzendruber wrote: > Hopefully I'm not out to lunch here. I ported tftp-hpa to our proprietary > OS, VOS (at stratus.com). We've always runs the old legacy tftpd from > inetd, so I wanted to continue doing so with tftp-hpa. It seems to work > okay, but I noticed that the code in tftpd.c has a 'while (1)' loop that > has

> Correct. Like most UDP-based inetd services, tftpd is intended to be run in 'wait' mode. When the first request arrives, inetd starts the service but does not read the incoming packet (it can't, because it has no way to pass it along to the server). After that, inetd ignores that socket until the server exits. This isn't critical for tftp, but it does help to keep down the

Hello all, Tested on linux 2.6.18 (Centos5) and FreeBSD 7.0. You would execute it like below (which basically makes tftp reply back with same port is listening on ) tftpd --port-range 69:69 -4 -s /tftpboot/ --- tftp-hpa-0.49/tftpd/tftpd.c 2008-10-21 01:08:31.000000000 +0300 +++ tftp-hpa-0.49-tftpd-reuseport.c 2010-03-03 15:19:26.000000000 +0200 @@ -524,6 +524,11 @@ #ifndef __CYGWIN__

Hi! I am using OpenBSD 4.4 with the build-in TFTP-Daemon for PXE. Distributing OpenBSD works fine. Now I want to distribute OpenBSD and WinPE. I've installed PXELinux 3.72 and configured it. Works also fine for PXELinux and distributing OpenBSD. To distribute WinPE I need a remap rule (\ -> /) for the TFTP-Daemon. I've created a file /etc/tftpd.remap with the following rule: rgG \\ /

> -----Original Message----- > On Behalf Of Geert Stappers > Sent: Sunday, August 25, 2013 6:42 AM > Subject: [syslinux] logging location of tftpd-hpa > > On my previous TFTP server I had logging. I did see all requests in logfiles. > > On my current TFTP server I have also added the options '-v -v -v', but nog > logging. At least I can't find it them in

On 01/30/2014 11:09 AM, Dan Swartzendruber wrote: > > Yeah, I get this part. I think I misunderstood what xinetd was doing - I > thought it was waiting for tftpd parent to exit and not processing > anything else. So xinetd is ignoring tftp port during this sequence, and > any new requests come in and are serviced by the parent tftpd which spawns > new tftpd children to do the

It seems that tftpd-hpa is more suitable at serving arbitrarily large files (greater than 65535 blocks long; with pxelinux.0 using a default block size of 1408 this is 92,273,280 bytes) as atftpd will complain in the log stating "Requested file to big, increase BLKSIZE". I saw that a while back HPA mentioned that atftpd was probably more scalable (number of clients) while tftpd-hpa is

Hi, I have a question on tftpd on Slackware - I know this is an embedded Linux forum, but I think it still must be the appropriate place to ask. I have hpa-tftpd V0.40 on Slackware 9.1. No matter what I do, I can't get files transferred to the tftp server. I just get timeouts - no messages in /var/log/messages or in /var/log/syslog - just dealthly silence. This is the configuration line

Hello, This about remapping in the HPA tftp server. A client does request for '/tftpboot/ncd4/foo' which should be 'ncd4/foo' I have created a remap file that looks now like this: r tftpboot/ncd4/modshmx/login.hmx ncd4/modshmx/login.hmx r tftpboot/ncd4/modshmx/setup.hmx ncd4/modshmx/setup.hmx r tftpboot/ncd4/modshmx/term.hmx ncd4/modshmx/term.hmx Because r

Hopefully I'm not out to lunch here. I ported tftp-hpa to our proprietary OS, VOS (at stratus.com). We've always runs the old legacy tftpd from inetd, so I wanted to continue doing so with tftp-hpa. It seems to work okay, but I noticed that the code in tftpd.c has a 'while (1)' loop that has this at the end: /* * Now that we have read the request packet from

hi, i try to get this tsize capable tftpd running, but it doesn't fork. (as read the strace output and the process table) strace: 9122 execve("/usr/sbin/in.tftpd", ["/usr/sbin/in.tftpd", "-u", "nobody", "-s", "/var/tftpboot/"], [/* 35 vars */]) = 0 9122 uname({sys="Linux", node="saturn", ...}) = 0 9122