similar to: odd pxelinux/tftp-hpa problem

First, THANKS! The SYSLINUX/PXELINUX s/w and docs are great. I have been able to set up a working server for PXE boot in very little time, using our existing Win2k DHCP server and a Red Hat 7.2 Linux server for tftp, etc... It took very little time (compared to an earlier effort 4 months ago.....) and the pxelinux/menu/memdisk environment is great for us. The environment seems to support PXE

Hello. In my case I can successfully boot up my Thinkpad X32, but the same configuration doesn't work for my desktop computer with Intel network card, with Intel Boot Agent 2.2 DHCP server is 10.0.0.1, tftpd (used tftp-hpa) runs on 10.0.0.32. netstat told me the daemon listen to 69 UDP port just fine. running tftp in commandline also shows it works (retrieve pxelinux.0 less then 1 second).

Hi, I have a new server HP proliant DL320 G4, with two 160 GB SATA hdds.. I have installed CentOS 4.5 with mdadm without any problem, but when I disconnect one disk the server does not boot or I received a kernel panic when booting... I have disabled the SATA embeded raid (BIOS) and nothing.. I've also download the driver from HP site HP (Embedded SATA RAID Controller Driver Diskette for Red

As subject says: With Intel PXE stack version 4.x (stack identifies itself in BIOS as IBA 4.0.x or 4.1.x), pxelinux' localboot option hangs instead of going to BIOS. This does not happen with older PXE stack. I have a feeling that the this broke somewhere in version 2.x - I *believe* 1.75 PXELINUX works fine - but haven't had a chance to try again. -alex

Good morning, I''m new to rails and am having some basic questions in development. See if anyone can help me with a test problem. I need to test if my model "Procedure" is linked to the workflow. If not, the system must acknowledge an error. Below is the code that is in the file test \ unit \ procedure_test.rb. require ''test_helper'' class ProcedureTest <

I have one HP Proliant DL320 G5p, where for some reason, the AHCI mode is not enabled. According to server specs, it should have AHCI/NCQ capability, but ata_piix module gets loaded during bootup, not ahci module. Any ideas how to enable AHCI mode? lspci output: # lspci 00:00.0 Host bridge: Intel Corporation 3200/3210 Chipset DRAM Controller (rev 01) 00:01.0 PCI bridge: Intel Corporation

Sorry if this has been asked previously. Does CentOS support IDE hardware RAID on HP DL320? Thanks, -j

Cordial saludo. Estoy teniendo un problema al convertir una columna categórica a numérica. Espero que me puedan colaborar. Esta variable está en números escritos, es decir, "uno", "dos" etc. Ya los cambie por números (que siguen siendo factores) mediante fct_recode y quise de ahí convertirla mediante as.numeric pensando que R iba a identificar los números y no iba a alterar el

Hello Arnaud, On 05/04/14 22:01, Arnaud Quette wrote: > Philippe, Ivan, > > please see https://github.com/networkupstools/nut/issues/118 > and send back your data. I've pasted the requested files in github, but the auto-formatting may have damaged them, so here they are. Also, when I ran gen-snmp-subdriver.sh, it gave me the following message:

Hello, I am pxebooting a large linux kernel (with embedded initramfs) that is around 250 MB in size. When booting a board in legacy BIOS mode, the pxelinux.0 executable is transferred to the board and takes over, from where loading and booting this large kernel works as expected. Actually, better than expected, as no tftp file size limit is incurred. If I change the BIOS settings to UEFI mode,

Hi, I have this strange problem I need some help with.. It appears that I have harddisk noise captured by a Digium TE410P card (Same problem on 2 identical machines..) The machines are two Compaq Proliant DL320 G3's... Does anyone else have this problem.. Kind Regards Claus Futtrup --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com).

I am trying to install on a DL320 proliant. The disk is not being recognized. It fails when setting up disk with "no devices" found. I dont get an sda or cciss either one. I tried to disable the on board smart array controller? That didnt seem to make a difference. Is there something special I need to do? Thanks, jerry

All, I have a question on how to deal with a quirk of the Intel Boot Agent. Both for PXE boots and for EFI boots. I've noticed this IBA quirk for years. According to the "DHCP options" RFC, variable length DHCP options are not necessarily null-terminated. Here's the details: >From DHCP Options and BOOTP Vendor Extensions (http://tools.ietf.org/html/rfc2132#section-2)

Hi, I am looking to connect 66 analog phones to an asterisk box. I was thinking of a Xorcom astribank 32port (2 of them and another 8 port). this is because the phones have no near connection to an ip network, so replacing the phones in favor of voip phones+network cabling is kinda out of the question. In your experience, will these units support all the phones talking at the same time with

Additional question: I noticed on the HP Website that the latest version of "CPQPOWER.MIB" (1.76, dated Sept. 19, 2013) was more recent than the related file (./drivers/compaq-mib.c) in the NUT driver. Is the MIB structure as implemented on the management card perhaps no longer in line with the NUT driver ? The latest MIB file can be downloaded from the following URL:

I saw Nate Carlson's message saying "..and it has been tested on amd64". I just installed it on an HP DL320 with Intel Pentium D 930, running i386 Sarge+backports. The packages seem to work here with Intel VT as well - in fact I just got through the Windows 2003 installation to the point where I could switch from VNC to RDP. Cool! Note to self: maybe one shoud start hacking

Hello, I'm trying to boot a HP Proliant DL320 G5 with a HP Smart Array E200i RAID card (latest BIOS and latest RAID card firmware). With menu.c32 or vesamenu.c32 from syslinux 3.50 the system hangs Booting from local disk... PXE-M0F Exiting With the latest dev version (3.52-pre) it hangs with : vesamenu.c32: attempted DOS system call The issue has already been reported but

Hi gang! I'm using Centos 4.4 at work on a HP Proliant DL320 G2, which has a Hypterthreaded Pentium IV CPU. I used to use RHEL WS 2.1 on it, and RH installed and used the SMP kernel. Centos 4.4 did NOT install the SMP kernel. Is there some reason why I should NOT install it myself? I.e., some reason why an SMP kernel shouldn't be used on such a machine? Gracias! -- ---- Fred Smith --

Hi gang! At work I have a DL320 G2 machine I use as my desktop (I know, weird!...). Back when I ran RHEL WS 2.1 on it, it always ran a SMP kernel because it has a HypterThread capable processor. When I installed (fresh from scratch) Centos 4.4 on it a while back, though, Centos installed only the UP kernel. I've looked in the BIOS for settings to enable/disable HT support and I don't

> Hello, > > I am pxebooting a large linux kernel (with embedded initramfs) that is around > 250 MB in size. > > When booting a board in legacy BIOS mode, the pxelinux.0 executable is > transferred to the board and takes over, from where loading and booting this > large kernel works as expected. Actually, better than expected, as no tftp > file size limit is incurred.