similar to: HP DL140G2 and SATA woes

I am trying to get PV drivers running on both Centos 5.1 and Centos 5.3 HVMs, my DomU is Centos 5.2 with Xen 3.31. For 5.1 I install the kmod-xenpv RPM but for 5.3 the drivers seem to be built-in. For the network drivers to work I had to unload the Realtek NIC driver and renamed its .ko files to stop it loading. Adding the Xen-Vnif alias to modprobe.conf then got the PV NICs working nicely (Much

Hi, can anyone provide any pointers as to how to avoid this issue? A CentOS 5.3 domU on snv_111 dom0 is crashing on bott unless I remove /lib/modules/2.6.18-128.1.6.el5/kernel/drivers/xenpv_hvm dom0: haggis:~$ uname -a SunOS haggis 5.11 snv_111 i86pc i386 i86xpv Name: SUNWxvm Summary: Hypervisor Header Files Category: System/Virtualization State: Installed

I''m trying to pass my SATA controller through to a domain and have run into a weird situation. I have two machines with the same general class of hardware (Intel PIIX) and the pass-through works on one machine but not the other. On the non-working system, the SATA controller makes port reads, but they don''t return the correct values. For example, when running it in dom0, when

Hi, One of my servers in a IDC in another country mysteriously went down this morning, and when I contacted the IDC, I was told that XEN doesn''t boot up, as follows: [QUOTE] This is error message on the screen " Error 19: Linux Kernel must be loaded before initrd" Server is currently up with 2nd kernel. Please check the grub.conf. [/QUOTE] Looking at grub.conf, I see the

Hi, I have a dell poweredge 850 with centos 4, freshly installed. I'm now trying to add in a fibre -> sata raid enclosure with LSI HBA's in the 850. My problem is the enclosure gets detected first, hijacking sda and sdb from the internal SATA drive and causing kernel panic at boot time. I've tried changing the order in modprobe to the following: alias eth0 tg3 alias eth1

we have DELL R900 with CENTOS 5.3 in it. This DELL R900 come with one integrate PERC6/I and two PERC6/E card. DELL 6/I control 5 internal disks. The original disk sequence are: /dev/sda1 /boot /dev/sda2 / /dev/sdb1 swap ... after I configured PERC6/E disks and reboot, /dev/sda change to RAID disk and original /boot and / change to /dev/sde1 and /dev/sde2. My modprobe.conf is: alias

Hi, One of my servers in a IDC in another country mysteriously went down this morning, and when I contacted the IDC, I was told that XEN doesn't boot up, as follows: [QUOTE] This is error message on the screen " Error 19: Linux Kernel must be loaded before initrd" Server is currently up with 2nd kernel. Please check the grub.conf. [/QUOTE] Looking at grub.conf, I see the

I installed a 4.1 x86_64 with kernel 2.6.9-11.ELsmp (rpm) initially. My box is tyan 5350 and a SATA harddisk The install was successful and the harddisk was detected as /dev/sdaX But strangely, when I first reboot my machine. The harddisk change to /dev/hdaX What is the problem ? Below are some of dmesg output hda: WDC WD1200JD-00HBB0, ATA DISK drive Probing IDE interface ide1... Probing IDE

The 8168B (02) NIC works well except that it does not go into promiscuous mode despite advertising itself in that mode after being so directed with ifconfig. Unfortunately, the little box is destined to be an IDS monitor, so that function is essential. The board is an Intel Atom 330 run as x86_64, the nic is internal. We tried three drivers: the one in the 2.6.18-128.1.10.el5 kernel yields

Hi folks, I have an HP Proliant 140DL G2 server with what appears to be an IDE drive in non-DMA mode. Performance on the server is extremely bad when large amounts of disk activity is taking place. I think the problem is that my drive is not in DMA mode: # hdparm /dev/hda /dev/hda: multcount = 16 (on) IO_support = 0 (default 16-bit) unmaskirq = 0 (off) using_dma = 0 (off)

Hi all I'm trying to setup second ethernet on Dell 2950 server but there isn't any eth1 device (in the bios are ON) # dmesg |grep eth eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f8000000, IRQ 169, node addr 001c23d878bb eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f4000000, IRQ 169, node addr 001c23d878bd

I'm trying to install CentOS 2.1 on SATA drive that lives on ICH7R controller. I have the controller setup in BIOS to "compatibility" mode, which means it should look just like regular IDE controller to the OS. In this mode, ide0 and ide1 are PATA controllers, and 4 SATA ports are mapped to ide2 and ide3. If I boot from the 2.1 installation CD, all the drives are detected

Hi people, I installed a via SATA controller in a CentOS release 3.8 (Final) - I needed additional disk space. After the first boot, the kudzu service, added the following line to /etc/modules.conf: alias scsi_hostadapter sata_via and I rebooted. After reboot in dmesg one can see: scsi0 : sata_via scsi1 : sata_via Vendor: ATA Model: SAMSUNG HD080HJ Rev: WT10 Type: Direct-Access

hi you, I'm having problem with voice quality on my trixbox using TDM2400B.The trixbox is connected via 20 FXO ports on a TDM2400 with the hardware echo cancel module. Echo cancel almost works, but the users hear what they describe as a 'background crackle/buzz' coming back when they talk. anyone have the same problem? pls help me. thanks a lot. my trixbox and config

Hi, I'm currently trying to install CentOS 5.5 on a series of Lenovo Thinkcentre nettops. At first, the install CD boots OK without any options, but when it comes to formatting, the process can only be described as terribly slow... it took about half an hour to format the 160 GB disk. A few cups of coffee later, the system boots with the following messages on bootup (right at the

I'm having trouble getting a Centos installation to boot on a system with hdd's hanging off an AHCI hba. Long ago, I posted about only seeing four of the six sata ports on my asus server board. According to research I've done since then (I now need the ports!), the solution is to enable the AHCI bios, which turns on NCQ and the last two ports. The already installed system does not

Hello All, I have a machine that crashed. Some part of the motherboard (power supply-related) went south. The motherboard, CPU and memory have been replaced with a much newer architecture. The OS and data are intact on two SATA drives that were RAID1 with LVM. I am going to use 'linux rescue' to recover the LVM backup so I can mount the RAIDs (there were two) in a new CentOS

Hi all, I have a problem during the lauching of my first virtual image. First thing : domain 0 is on fedora core 6 (probably a xen package made in fedora :-S, sorry ...) Second thing : the error is really traditional (i already had it with uml) but there i am blocking. here my config file (for image on logical volume, swap too) root = "/dev/sda1 ro" [root@p-virtvip8 xen]# cat p-virtser9

We are happily running xen on a server which uses a SATA driver (thank you all you xenists for producing such a great product). However, we are creating a custom kernel for a domU. When we attempt to run mkinitrd we get: No module ata_piix found for kernel 2.6.11.12-xenUIPSec, aborting. This is the SATA driver. In the past (xen 2.0.5), we simply ran make ARCH=xen menuconfig and told it to

Hi, When I install Oracle RAC on Xen VM, some problem occurred. How can I configure two NICs on a Xen''s DomU. You know, RAC''s installation requires two NICs on a node. I am a newbie about Xen. Please give me some advice. Thanks. Yaqiong lee Beijing,China -----邮件原件----- 发件人: xen-users-bounces@lists.xensource.com [mailto:xen-users-bounces@lists.xensource.com] 代表