similar to: onboot=yes not working for eth0.x:y interfaces?

Hi, Whats the new way of creating sha512 passwords in EL7? In Centos6 I used grub-crypt but that does not exist anymore.

Hi all, I use CentOS5.x + Xen in production for virtualization. I use it with bridged vlan networks and bonding (active-backup) like that: eth0 eth1 | | ------- | bond0-------bond0.10---------bond0.12 ... | | | | vlanbr10 vlanbr12 dom0 | | ------------- -------------- | |

Hi all, I've a little problem with CentOS 6 and EFI on Dell Poweredge R510... My Logical disk (hardware raid) is a little bit greated than 9TB, so i must use EFI in order to see the whole disk space and boot on it, but my box don't want to boot on CentOS 6 x86_64 Install DVD when i'm in EFI boot mode. someone has successfully installed CentOS 6 x86_64 in EFI mode ? Regards.

Hello What I''m looking for is how to configure the Linux QoS module to do global rate limitation for two (or more) 802.1q pseudo network devices. I naturally suppose there is a possibility with IFB. I don''t want to use IMQ because it''s not integrated to my kernel v2.6.21.1 and I didn''t find IMQ patches for it nor for the iptables package I use (v1.3.7).

1. Link state monitoring added. We discovered the following problem with the existing bridge code. The code doesn't monitor the link state of the interfaces. When using two cisco switches with two Linux bridging firewalls the following problem exists. When the Cisco switch that has the blocking (stp) Linux bridge attached dies, the Linux bridge no longer receives stp packets and changes

Hi, I've set up a virtual machine and plugged it into a bridge on the host. When i configure an ip for eth0 in the guest i can ping other machines fine but when I add an interface eth0.10 in the guest and add an ip pings using this interface do not work. When using tcpdump in vnet0 on the host I can see the icmp packets when I ping using eth0 in the guest but not when I use the eth0.10

Hi all. What is the canonical way of getting xen to fully work with 802.1q (vlans) ? After (re)searching i found many ways but so far none is working. platform is gentoo (x86/32) and netwerk card a tg3. xen is v3. my config is as follows ... eth0 is simply up (with no ip) and i created several eth0.x interfaces corresponding to several vlans. eth0.10 is de ''default'' vlan

Hi I have problems with shaping traffic running through a VLAN. I have done the following set up: I have a linux box a gateway. I wish to use VLAN on the internal interface (eth0). eth1 is connected to the internet. I will like to be able to shape the dowstream traffic. I have set up the followingon the gateway: vconfig add eth0 10 tc qdisc add dev eth0.10 parent root handle 1: htb default 2

Hi there, -- Christian Lyra PoP-PR/RNP _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

I was reading in the archives that people were looking into how to play ogg orbis on the Lyra. Did anything happen with that? I have a lyra, and I'm looking into buying another mp3 player soon-- if there is a way to play ogg vorbis on one of the ones I'm looking at, I'd really like to know. Ana <p><p>__________________________________________________ Do you Yahoo!?

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I''ve a problem on the broadcast it is adding some additional route to the router which caused me some problem... Below is my /etc/shorewall/interface swtmng1 eth0.1 202.73.10.127 norfc1918 apmng1 eth0.10 202.73.8.7 norfc1918 dist1 eth0.1000 202.73.11.255 norfc1918,nobogons idc1 eth2.50

Hi. I am trying to setup my firewall in DomU. However, I have got a little problem. My pon dsl-provider exits with following message. Nov 18 09:44:40 alsfw01 pppd[1723]: Plugin rp-pppoe.so loaded. Nov 18 09:44:40 alsfw01 pppd[1723]: Linux kernel does not support PPPoE -- are you running 2.4.x? Nov 18 09:44:40 alsfw01 pppd[1723]: Exit. I am running xen out of the box on Debian Stable. My

Hi, I'm wondering about the impact of using both dom0 and domU's on a server at the same time. I'm worried about the performance impact of running a Mysql server in a domU and now I'm thinking about moving the Mysql part of a LAMP setup into dom0 and running a few Apache guests as domUs. Since the Apaches will serve mostly from an NFS share they won't have much impact on

Hi all, I''m sure I''m soing something wrong here. I am trying to set up a rate limit inside another rate limit. eg. I have a 512K rate limit on a particular VLAN. I am using an IFB so that packets passing through the bridge are counted at each port.(ie the throughput is limited to 512K, not just the traffic in one direction.) This part works OK, but I also want to limit a

hi, at home I have setup a kvm virtualization lab. I have a layer 3 switch, a host with 3 nics and centos 6.3. In the layer 3 switch I have setup a couple of vlans: vlan 1 (default), 5 (quarantaine) and 10 (out-of-band-management). nic0 is configured in the switch as a trunk interface that sees all vlans. nic2 is an access port on vlan 5 and nic1 is not yet in the picture ;-) eth0 is bridged

Does anyone know if there is a fix for nscd segfaulting after a short period of time. Googling for it came up with one result that suggested deleting the files in /var/db/nscd , but that didn't help. Another result was about run away processes which is not the problem I'm having. They are x86_64 boxes. output from /var/log/messages Oct 9 12:56:38 lyra kernel: nscd[11660]: segfault at

Hi, I'm having trouble getting networking to work and I'm not sure what I'm doing wrong. The network interface of the host is connected to a switch-port that is configured as trunk and allows tagged traffic for vlan id 10. The host itself has the interfaces eth1.10 and eth1 defined. eth1.10 is configured with the primary ip address of the host system and eth1 is slave of the bridge

On 09.12.2015 00:39, NightLightHosts Admin wrote: > On Tue, Dec 8, 2015 at 5:26 PM, Dennis Jacobfeuerborn > <dennisml at conversis.de> wrote: >> Hi, >> today we ran into a strange problem: When performing a regular Windows >> 2008r2 update apparently among other things the following was installed: >> "SUSE - Storage Controller - SUSE Block Driver for

hi all What´s the best way to have my DVD-R/RW burner working in a DomU? Just ''phy:hdc,hdc,w'' would do it? or there´s some other way? thanks in advance, Christian Lyra _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

I think it should be sufficient to do as following: - create and test the vlans as normal (i think you already did this) - try to create the bridge as follows (for the first try without starting xend): # network-bridge start netdev=vlan100 bridge=xenbr0 at least this was working on my debian testing installation but i have a problem now with incorrect tcp checksums in dom0 or domU. See my