similar to: ISDN accounting software

Tzafrir, > cross-posting to asterisk-users and to asterisk-dev > is not a good idea. > You should know that by now, as you have been told > that numerous time. I cross-posting because nobody answer ! I think some people are able to answer this question ? Please, don't tell me people here are not here to serve you . > Your question, as phrased, was probably relevant to >

Tzafrir, > cross-posting to asterisk-users and to asterisk-dev > is not a good idea. > You should know that by now, as you have been told > that numerous time. I cross-posting because nobody answer ! I think some people are able to answer this question ? Please, don't tell me people here are not here to serve you . > Your question, as phrased, was probably relevant to >

Has someone created a how to or a tutorial for installing/configuring DELL openmanage on centos ? --

Hello All ! Recently I have upgraded NUT to 2.4.1, and now I can't monitor old IMV LanPro S3 UPS with old SNMP board. Previously it is monitored OK, but now snmp-ups refuses to start: [root at perforce /usr/local/etc/nut]# /usr/local/libexec/nut/snmp-ups -a lanproups -DDDDDDD Network UPS Tools - Generic SNMP UPS driver 0.44 (2.4.1) debug level is '7' SNMP UPS driver : entering

All, I need to run this by everyone and see if someone has any idea's. I have a asterisk server setup and currently am receiving the inbound calling number where the name should be. My setup is.... One pri terminating into a Cisco 2431 router Sip messages from the Cisco get sent to a asterisk server linksys ata's a each remote end. I can receive the calling name if the call originates

# I originally intended to post this question here. # But it took some time for subscription authorization process. # So I have posted the same question to the forum when I was waiting # for the subscription confirmation notice. # It seems to me the forum is not so active, let me drop here too. Hello, The following WinSNMP trap receive program ''win_snmp.rb'' causes ruby

Hi guys Am trialing an install of SoEasy accounting software. Program is written in SuperBase - older version that is like VBScript language. Does not require registry settings etc as you can blow away and reload windows without effecting the program. Got the program to install and even got the front company menu displayed. but once the program has closed down it spits back the following error

Hello. It seems very very strange to me that nobody talks about connecting ISDN lines to asterisk using a device with RCAPI Support. There are some devices (most of them isdn routers, like the famous Cisco 800 family) that support this protocol. It basically is an ISDN to IP gateway. There used to be software that used this technology to send and receive faxes, act as voicemail and even ISDN

Good day, anyone out there running an ISDN pbx behind an Asterisk server with an AVM active card? At this moment Asterisk is connected to the internal ISDN bus of the PBX, but I want to control the calls coming in from the outside, before sending them of to the PBX. Any BTDT is greatly appreciated. rgds pos

http://bugzilla.netfilter.org/show_bug.cgi?id=783 Summary: ipset fails to parse port names with hyphen for bitmap:port type Product: ipset Version: unspecified Platform: All OS/Version: Debian GNU/Linux Status: NEW Severity: normal Priority: P5 Component: default AssignedTo:

-----BEGIN PGP SIGNED MESSAGE----- ============================================================================= FreeBSD-SA-02:11 Security Advisory FreeBSD, Inc. Topic: ucd-snmp/net-snmp remotely exploitable vulnerabilities Category: ports Module: net-snmp Announced:

Hello I'm trying to setup SNMP on my Centos 4.2 server. I want the ability to monitor the disk and some other non default settings that can be defined in snmpd.conf but when I request the data, it doesn't give the disired results. Config below and trap results below. Thanks in advance for any help. Kevin [root at localhost snmp] snmpget -v 2c -c public localhost disk

Hello, I am looking for good instructions on how to configure NUT to receive SNMP Trap signals and how to shutdown a server. My setup is: NUT: version 2.7.1-1ubuntu1, from package OS: Ubuntu 14.04.5 LTS UPS: Tripp Lite SMART3000RM2U The only thing I was able to understand from the documentation is to an entry in ups.conf: [tripplite-pa3] driver = snmp-ups port =

Hi All, i'm going crazy trying to make asterisk work with the following hardware: 02:05.0 Network controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02) Subsystem: Cologne Chip Designs GmbH ISDN Board Flags: bus master, medium devsel, latency 16, IRQ 17 I/O ports at d000 [disabled] [size=8] Memory at ec000000 (32-bit, non-prefetchable)

Hello! My name is Denis Shaposhnikov. I'm looking for a job in EU (Germany is preferably) as a UNIX/FreeBSD system administrator and/or network administrator that lets me utilize my experience in an Internet Service Providing (ISP). Skills: * Operating systems: UNIX (FreeBSD 2.2 - STABLE), Cisco IOS (10.x - 12.x), ZyNOS. Understand how systems work and is able to apply this

Olle ?) aiming to unify logging, eventing, monitoring (AMI, SNMP, ...) APIs. I think that thread occurred when it was decided to include a version number in Manager interface. I agree this is an interesting idea ... The use case that made me ask this is here : I've got a running system which is working ok up to a moment it stops to dial out on ISDN-BRI spans (incoming calls are ok). When

Is there some type of sawmill like type of application for displaying syslog results in a web based front end ? --

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all I have already a fully operational Asterisk PBX connected only to the IP world. As a necessary step before smashing our current PBX, I need to install and configure an ISDN card able to take an incoming E1 line provided by Eircom. That's the one and only ISDN line we will ever have, so I am planning to get a single port card similar to

Since 2004 asterisk/libpri have been able to receive the Calling Sub Address in the ISDN setup message, and the dialplan was able to use it if required. It's support is limited to only NSAP, not BCD or user formatted. At the time 25/06/04 the questioned was asked, wouldn't it be a good idea to be able to transmit it as well, but that never got implemented, as it wasn't required at

Hi, i was able to solve my problem. During my playing around with * and capi i changed several options in config files. I did this while my * was running. To test if my changes where successful i entered "reload" on * console. This didn't help. But after i stopped asterisk and startet it again, everything worked perfect. So it seems that doing a reload while asterisk is running