similar to: Kernel 2.6.9.42 (.0 and .0.2) Wireless Problems

Hi Folks, I'd like to install my USB-WLAN-Stick Netgear WG111v3. Ndiswrapper works correct after installing Kernel-Modules from atrpm ndiswrapper-kmdl-2.6.18-53.1.19.el5.centos.plus-1.52-16.el5.i686.rpm. But by calling wpa_supplicant with wpa_supplicant -i wlan0 -D wext -c /etc/wpa_supplicant/wpa_supplicant.conf -d machine freezes. My wpa_supplicant.conf:

hi all, this is my first hit on the mailing list. hope i m posting in the right place. well, i have a dell vostro 1510 laptop with broadcom wifi adapter. n it doesnt work! :( i installed the wifi drivers with ndiswrapper. iwconfig shows the following. [root at laptop ~]# iwconfig lo no wireless extensions. eth0 no wireless extensions. sit0 no wireless extensions. wlan0

I know, I know... don't use the non-standard kernels unless you have to... BUT: I have a D-Link N150 USB card. Bus 001 Device 004: ID 0846:9030 NetGear, Inc. WNA1100 Wireless-N 150 [Atheros AR9271] This isn't supported in C5, but it is supported in newer kernels (ath9k_htc). So let's try NDISwrapper: # rpm -i kmod\-ndiswrapper\-1.56\-1.el5.elrepo.i686.rpm

I am using a Netgear MA401 with the wi driver, and am having trouble using wpa_supplicant to set static WEP keys. I have the wlan_wep.ko module loaded with wlan and wi built into the kernel. My wpa_supplicant.conf looks like this: ctrl_interface=/var/run/wpa_supplicant ctrl_interface_group=wheel network={ ssid="INTERNERD" scan_ssid=1 priority=1 key_mgmt=NONE

This is a new Centos 5.1 install on a HP nc2400 (that use to run XP). Completely clean install; blew away the XP partitions... After applying all the updates, and configuring for the rpmforge repo, I used yumex to install dkms and the dkms-ipw3945, ipw3945-firmware, and ipw3945d rpms. lsmod|grep ipw shows: ipw3945 180391 1 ieeee80211 33417 1 ipw3945 and dmesg)grep

first, the short form of the question -- has anyone got that wireless adapter working on centos 5.5 and associated with an access point that uses WPA/WPA2 security? and the details. in a classroom where there is *no* wired networking at all, all PCs have only that wireless net adapter, which works fine on windows but, after installing centos 5.5, unsurprisingly, we have no networking. there

I've got CentOS 5 installed on my hp pavilion ze 5300 laptop and the network configuration UI says my wireless NIC has been correctly identified and assigned what appears to be the right Broadcom device driver on eth1. However, the inteface doesn't come up. Google doesn't find anything recent about using Linux with Broadcom except for someone's passing remark that Ubuntu 7 beta

I have not installed the madwifi specific kernel stuff (kdml and hal-kdml) from atrpms. I have installed with wpa rpms. And my Atheros card is working with almost no work on my part (other than runing wpa_supplicant as a deamon). Nice!

I seem to be able to lock my machine by going into wpa_cli and asking it to 'reassoc'. The reason for question mark after "hard" is that debug information (caused by wlandebug and athdebug) is being printed on the console. The only way to get machine's attention is to hold power button for 8 seconds. Note: manual reassociation is just the handy way to reproduce the problem

I want to buy a laptop and install CentOS 4 on it and have the wifi work when I'm done. (Hoping for reasonable specs: 2GHz, 40GB drive, 1/2 to 1 GB RAM, CD-ROM, light and thin, 13 or 14 inch screen....) Any recommendations?

Hi, I am running Centos 4.1 on a Dell D610 with ipw2200. Any good howto for running wpa-psk? I have searched and not found much related to RHEL or CentOS. -- Thanks http://www.911networks.com

Hi, I've got a task to have a small number of laptops netboot Linux over WiFi. The kernel is loaded off the USB stick of cource, it's off topic for now. The WPA-supplicant daemon is started early by dracut off initrd. It works. Mostly. The problem is that upon shutdown systemd terminates all the processes FIRST and unmounts filesystems NEXT. Guess what? Upon termination,

Hi everybody, First of all, let me say that I searched a lot on the internet. I spent several hours sitting after my notebook, but I can't configure my network bridge in Ubuntu. I'm really desperate, so I hope somebody can point me out what I'm doing Hardware: ----------------------------------------------------------- $ lspci | grep controller 06:05.0 Network controller: Intel

I remember being a small part of and following this thread a few months ago. <http://lists.centos.org/pipermail/centos/2006-May/065091.html> I've been attempting a go at getting wpa_supplicant running on CentOS 4.3 and haven't had much luck. I'm assuming my failure is my lack of knowledge on the subject, but anyways. First, my normal setup is as follows: IBM Thinkpad R40

On 22 December 2015 at 10:33, Sylvain CANOINE <sylvain.canoine at tv5monde.org> wrote: > > ----- Mail original ----- > > De: "Marcelo Ricardo Leitner" <marcelo.leitner at gmail.com> > > ?: "centos" <centos at centos.org> > > Envoy?: Lundi 21 D?cembre 2015 21:46:10 > > Objet: Re: [CentOS] Network services start before network is

I have been playing around with 3 ath based FreeBSD boxes and seem to have got everything going via WPA and a common PSK for 802.11x auth. However, I want to have a bit more certainty about things working properly. What tools do people recommend for sniffing and checking a wireless network ? In terms of IDS, is there any way to see if people are trying to bruteforce the network ? I see

Actually I do a similar thing. I use a VM as my home/office firewall. It works quite well and I would argue it is as secure as your standard firewall based on something like openWRT running on dedicated hardware. I also run a wireless AP in bridged mode to allow local network access on an appliance. There should be no reason that you could not put both on the same physical hardware. As for

I have an Everex laptop (ick, but it was super cheap) that has an Atheros wireless NIC in it, but I can't seem to get it to connect to my wireless in-home LAN. Here's what I've done so far (that isn't working) - any suggestions? [root at marktop mark]# lspci | grep Ether 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 7c) 05:01.0 Ethernet controller:

HI I admit up front that I know just enough about wireless networking to know that I don't know much at all about it. That said, I'm hoping someone can help me learn a little bit... Specifically, could a laptop running Centos 5.1 be expected to (be able to) connect to a wireless access point using WPA2 security settings? I don't know if WPA depends on hardware support, or if

I have recently installed CentOS 6 on a system with a Realtek 8180L wireless card. The wireless card is detected properly and uses the rtl8180 driver. But it connects to our wireless network only after logging to the Desktop Environment (GNOME) and using the Network Manager Applet. In order to make the wireless card connect to the network automatically at system start up, I edited the Connection