similar to: lm_sensors rpm

Hello, I'm having problems with lm_sensors on the motherboard Supermicro X6DH8-G2+ sensors-detect gives me the output attached in the textfile sensors-detect-output.txt As soon as I execute the recommended 'modprobe smbus-arp' I receive the following message: FATAL: Module smbus_arp not found. When I execute sensors, I receive the following:

Problem and solution, not sure if correct After upgrading to 5.1 and restarting, lm_sensors complained "General Parse Error." Google pointed here: http://www.lm-sensors.org/wiki/Devices Where I found this under "SENSOR CHIP DRIVERS - STATUS" AMD --> "Since Kernel 2.6.19" Latest AMD K8 processors have integrated sensors which can be read directly without any

Hi All, I'm trying to get lm_sensors to work on a Shuttle with an AMD K10. The version of lm_sensors in the main CentOS repo is 2.10.7, which is two years old now. Support for the K10 was added about a year ago. So, does anyone know if there are binaries available for more recent versions of lm_sensors? Also, if anyone has knowledge of the sensors layout for recent Shuttle AMD motherboards,

Sorry if this has been around many times before, but I've done quite a bit of reading and searching for some type of human readable guide for setting up the lm_sensors for hardware monitoring. I've dorked around with the stuff in the system here, but after looking at the /etc/sensors.conf, I don't think I want to delve into that and try to pull out the right group of settings.

Tyan has posted a lm_sensors config file for the Thunder K8SE S2892 at ftp://ftp.tyan.com/software/lms/lms_s2892.conf However when I ran the sensors command on my S2892 I was getting a readout for an adt7463 chip that wasn't referenced in the config file. I emailed Raphael Deng at Tyan asking him to confirm the manual edit needed to get sensors.conf to refer to the adt7463 chip. His

Hi, has somebody already succeeded in creating a php-4.4 rpm under centos-4.4? php version 4.3.9 compiles perfectly, but taking the 4.3.9 spec and replacing the source tar.gz (and omitting the patches) doesn't work at all. I could provide you with details about compile errors, but I think I should check the availability of a 4.4 package before trashing you with details. TIA Regards

Hi, I just tried the below with the current version 1.0 RC15 (from the dovecot website) and I still got the Problem: telnet gives me the following output: -----8<-----8<-----8<-----SNIP-----8<-----8<-----8<----- +OK dovecot ready.u-ERR invalid command u s-ERR invalid command s e-ERR invalid command e r-ERR invalid command r -ERR invalid command u-ERR invalid command u s-ERR

Hi, I just tried the below with the current version 1.0 RC15 and I still got the Problem: telnet gives me the following output: -----8<-----8<-----8<-----SNIP-----8<-----8<-----8<----- +OK dovecot ready.u-ERR invalid command u s-ERR invalid command s e-ERR invalid command e r-ERR invalid command r -ERR invalid command u-ERR invalid command u s-ERR invalid command s e-ERR

hello, I have problem to install lm_sensors on CentOS 4.5 (Linux 2.6.9-42.ELsmp). I am getting error message "FATAL: Module bmcsensors not found." after I enter "modprobe bmcsensors". I got advice to install http://bmcsensors-26.sourceforge.net/ into my kernel, but I don't know how to do it. Does somebody has experience how to get lm-sensors working on CentOS 4.5 ?

Hi list, after a bit of struggling I found out how to cleanly install rkhunter ... maybe this is useful for you: * Download rkhunter (I downloaded v 1.2.8) * mv /etc/rpm/platform /root/etc_rpm_platform * setarch i386 rpmbuild -ta --target=i386 rkhunter-1.2.8.tar.gz * mv /root/etc_rpm_platform /etc/rpm/platform * rpm -ivh /usr/src/redhat/RPMS/noarch/rkhunter-1.2.8-1.noarch.rpm * wget

Hi list, is there any repository on this world where I can stick to and update to a stable and hopefully secure and hopefully long supported version 4.4 of php? EZ publish's software requirements as of the current version tells me that it requires php 4.4 which doesn't meet what Centos 4.4 or its upstream provides. For a certain project I want to use ez publish. Is there any solution

Hi, I'm trying a fresh install on a x86_64 (Supermicro X7dbe, 2xIntel Xeon X5450, 8 GB, 3WARE 9650SE-8LPML, 3 disks in RAID 5). The format takes quite long (2,7 TB), that seems to be normal, but then the first boot will not take place, instead the system loops. Any hints? The message follows: Regards Michael Mounting root filesystem. mount: could not find filesystem '/dev/root'

Hello, I'm trying to install centos-4.7 under kvm (for legacy reasons). I can't get the beast installed, it crashes (see output below). I'm using: qemu 0.9.1 kvm-72 libvirt-0.4.6 kernel 2.6.26 What can I do in order to get the installation being done? The host is a x86_64 machine (debian5). BTW, the installation for centos-5.2 works like a charm with the above configuration. TIA

Hi, I'm trying to install a CentOS 5.2 guest with virt-manager/qemu on a CentOS 5.2 system (X86_x64, 3ware 9650SE, 2 x Intel VT capable xeon cpus, 8 GB) Unfortunately I'm getting a crash in the guest install process. Other systems are installing smoothely, even Windows xp, but the above combination won't install. What works, too: CentOS 5.2 xen unmodified (i.e. fully virtual) guest,

Hi, shutting down a Centos6 kvm guest does not work from outside doing a 'virsh shutdown vmguest', I've installed the CentOS-6.2-x86_64-minimal.iso inside the kvm guest I reckon this is related to acpi ... # dmesg | grep ACPI ACPI Error: A valid RSDP was not found (20090903/tbxfroot-219) ACPI: Interpreter disabled. pnp: PnP ACPI: disabled acpiphp: ACPI Hot Plug PCI Controller Driver

Trying to get cpu temps from lm_sensors for a Tyan s4985 motherboard, just installed centos 5.4. Tyan release some lm_sensors conf files and other information which I have done, but I am not getting any cpu temps. I was wondering if anyone out there was running this board and if you have gotten temps working for your cpu, here is my output...Thanks in advance. w83627hf-isa-0c00 Adapter: ISA

Hi all :) Using lm_sensors, I can see few temperature indicator. M/B Temp: +39?C (low = +15?C, high = +40?C) sensor = thermistor CPU Temp: +33?C (low = +15?C, high = +45?C) sensor = thermistor Temp3: +53?C (low = +15?C, high = +45?C) sensor = diode What is that Temp3? It's the hottest. Which one is the best to use if I want to use lm_sensor as a general

Hi, has somebody already got xen running on centos 4.4? Does the tutorial under http://mark.foster.cc/wiki/index.php/Centos-4_on_Xen also work for version 4.4? I don't have my new server yet in order to try it (it will be delivered at the end of the week), but I'd like to read a little bit about it in advance. Thanks Michael -- Michael Kress, kress at hal.saar.de

On Monday 12 December 2016 12:15:10 David Both wrote: > The lm_sensors package is required for the sensors module of glances to > work. After installing lm_sensors, run sensors-detect. The sensors > command will show the sensors detected and their current values. glances > should then display the sensor readings. Somewhere tucked in the back of my mind a memory is screaming no.

Hello, I'm planning a server migration and being able to mount xfs file systems with the live cd would be a cruical feature. So before I download and try ... can anyone tell me whether the xfs is included in the 5.2 live cd? Later on I'm planning to install a new system with xen, 3ware 9550SX-4LP and xfs. The xen domains are of course located on xfs partitions. Do these features come