similar to: Problems with image.plot

Hello, Is there a simple way of stacking/merging two dataframes in R? I want to stack them piece-wise, not simply add one whole dataframe to the bottom of the other. I want to create as follows: x.frame: aX1 bX1 cX1 ... zX1 aX2 bX2 cX2 ... zX2 ... ... ... ... ... aX99 bX99 cX99 ... zX99 y.frame: aY1 bY1 cY1 ... zY1 aY2 bY2 cY2 ... zY2 ... ... ... ... ... aY99 bY99 cY99 ...

Hi R-community, I am doing a PCA and I need plots for different combinations of axes (e.g., PC1 vs PC3, and PC2 vs PC3) with the arrows indicating the loadings of each variables. What I need is exactly what I get using biplot (pca.object) but for other axes. I have plotted PC2 and 3 using the scores of the cases, but I don't get the arrows proportional to the loadings of each variables on

Hello I am trying to write a function that would plot timeseries easily... I aim at plotting two time-series on 2 different y axis sharing the same x-axis I succeded in doing so: plotTimeSerie(x,y,y2,[a lot of other args]){ ... plot() axis.POSIXct(side=1) #here I build the x-axis points() #here I plot the first time serie related to y-axis ... axis(side=2,[some args])

Dear *, I have to perform an ANOVA analysis to study the effects on the performance of some algorithmic components in the design of my algorithm. I have done a full factorial design for the following 5 factors (my response variable is "best"): $ model :'data.frame': 3360 obs. of 6 variables: ..$ best : num [1:3360] 0.108 0.573 0.625 1.057 0.451 ...

I have a general question about using thin plate splines in the surf and ordisurf routines. My rudimentary knowledge of a gam is that with each predictive variable there is a different smooth for each one and then they are added together with no real interaction term (because they don't handle this well?). Now, If I have two variables that have a high D^2 score and a low GCV score (I am

Hello, I thought that my Digium TDM400P would be the right hardware to support the zaptel timer, and put the following IAX.CONF entry to test, (trunk=yes) in the example below [VHAX] type=peer auth=md5 username=whoknows jitterbuffer=yes ;trunk=yes secret=terriblesecret host=4.5.6.7 qualify=1200 disallow=all allow=ulaw allow=gsm ;allow=g711u ;allow=g711a But, it didn't work. So I had to

Hi, I have a large data set that I input as a matrix, where I have 1:x rows with names AX, then x+1: y rows named AY, etc. The idea is that I have to count how many rows exactly I have with name AX and how many I have with name AY (or find which row numbers have names AX). Is there any way in R to count a number of rows with a name matching a required pattern? Thanks in advance, Katie --

Hi, I have downloaded the newest source code ocfs2-1.2.3.tar.gz from oss.oracle.com. After do the configuration I find a strange thing. Although my kernel is "2.6.9-11.19AX"(Asianux2.0 on a vmware server with a single processor configured), the configuration find that it is 2.6.9-11.19AX-smp. So after I make and install, those *.ko went to the wrong place. The reason is: 1.

I am trying to generate a set of random numbers that fulfill the following constraints: X1 + X2 + X3 + X4 = 1 aX1 + bX2 + cX3 + dX4 = n where a, b, c, d, and n are known. Any function to do this? Thanks, -Ala' [[alternative HTML version deleted]]

Hi, I have experimental response (Y) and many (important or not) actions (X). I want to create model: Y = aX1 + bX2 + ... + eX5 (1) from few most important actions of course. As I understand I have to use plsr for this task. I learned read.table and plsr R functions and how to plot some results from them, but still do not understand how I can get (or construct) function I need (function 1)?

> > You need to configure your legacy PBX to send a flash through from your > legacy phone to the legacy FXS port that is hooked to a * FXO port. This > is not something you can do from the * side. > > *0 is asterisk's way of doing this. You need to find out if your legacy > PBX has a similar method. It may not be possible. Of course you failed > to mention what kind of

Skipped content of type multipart/alternative-------------- next part -------------- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.298 / Virus Database: 265.6.6 - Release Date: 12/28/2004

Forgive me if this is a trivial question, but I couldn't find it an answer in former forums. I'm trying to reproduce some SAS results where they set two parameters equal. For example: y = b1X1 + b2X2 + b1X3 Notice that the variables X1 and X3 both have the same slope and the intercept has been removed. How do I get an estimate of this regression model? I know how to remove the intercept

Hi, Everything compiled correctly for the ocfs2 package, but so far the modules will not load with the "well known" module symbol error. FATAL: Error inserting ocfs2 (/lib/modules/2.6.16.27-0.6-smp/kernel/fs/ocfs2/ocfs2.ko): Unknown symbol in module, or unknown parameter (see dmesg) Okay not sure what is up here, any suggestions? BTW, this is the correct module location and I

Full_Name: Naoki Takebayashi Version: 0.65.0+R-release.diff (Oct 6, 1999) OS: Linux/Alpha Submission from: (NULL) (129.79.224.171) This will fix the "problem 2 (crash in fft)" in Bug ID #277 On Linux/Alpha, make check failed because R could not handle the following example in base-Ex.R ##___ Examples ___: # The Old Faithful geyser data data(faithful) : : ## Missing values: x <-

Already outdated, but rounded ;) I literally just opened the 5yrs logo, changed the text and then done: inkscape -z -o logo/fish-10yrs.{png,svg} cp {logo,website}/fish-10yrs.svg and then updated the rest of the files. Signed-off-by: Martin Kletzander <mkletzan@redhat.com> --- Makefile.am | 2 + logo/fish-10yrs.png | Bin 0 -> 65790 bytes logo/fish-10yrs.svg |

Signed-off-by: Scott Seago <sseago at redhat.com> --- AUTHORS | 17 ++++++ README | 10 +++ conf/ovirt-agent | 12 ++++ conf/ovirt-db-omatic | 12 ++++ conf/ovirt-host-browser | 12 ++++

depends on "autoconf: regenerate configure scripts with 4.4 version" This series removes some of the really old deadwood from the tools build and makes some other things which are on their way out configurable at build time with a default depending on how far down the slope I judge them to be. * nuke in tree copy of libaio * nuke obsolete tools: xsview, miniterm, lomount & sv *