Ido Schimmel
2022-Dec-08 15:28 UTC
[Bridge] [PATCH net-next 00/14] bridge: mcast: Extensions for EVPN
tl;dr
====
This patchset creates feature parity between user space and the kernel
and allows the former to install and replace MDB port group entries with
a source list and associated filter mode. This is required for EVPN use
cases where multicast state is not derived from snooped IGMP/MLD
packets, but instead derived from EVPN routes exchanged by the control
plane in user space.
Background
=========
IGMPv3 [1] and MLDv2 [2] differ from earlier versions of the protocols
in that they add support for source-specific multicast. That is, hosts
can advertise interest in listening to a particular multicast address
only from specific source addresses or from all sources except for
specific source addresses.
In kernel 5.10 [3][4], the bridge driver gained the ability to snoop
IGMPv3/MLDv2 packets and install corresponding MDB port group entries.
For example, a snooped IGMPv3 Membership Report that contains a single
MODE_IS_EXCLUDE record for group 239.10.10.10 with sources 192.0.2.1,
192.0.2.2, 192.0.2.20 and 192.0.2.21 would trigger the creation of these
entries:
# bridge -d mdb show
dev br0 port veth1 grp 239.10.10.10 src 192.0.2.21 temp filter_mode include
proto kernel blocked
dev br0 port veth1 grp 239.10.10.10 src 192.0.2.20 temp filter_mode include
proto kernel blocked
dev br0 port veth1 grp 239.10.10.10 src 192.0.2.2 temp filter_mode include
proto kernel blocked
dev br0 port veth1 grp 239.10.10.10 src 192.0.2.1 temp filter_mode include
proto kernel blocked
dev br0 port veth1 grp 239.10.10.10 temp filter_mode exclude source_list
192.0.2.21/0.00,192.0.2.20/0.00,192.0.2.2/0.00,192.0.2.1/0.00 proto kernel
While the kernel can install and replace entries with a filter mode and
source list, user space cannot. It can only add EXCLUDE entries with an
empty source list, which is sufficient for IGMPv2/MLDv1, but not for
IGMPv3/MLDv2.
Use cases where the multicast state is not derived from snooped packets,
but instead derived from routes exchanged by the user space control
plane require feature parity between user space and the kernel in terms
of MDB configuration. Such a use case is detailed in the next section.
Motivation
=========
RFC 7432 [5] defines a "MAC/IP Advertisement route" (type 2) [6] that
allows NVE switches in the EVPN network to advertise and learn
reachability information for unicast MAC addresses. Traffic destined to
a unicast MAC address can therefore be selectively forwarded to a single
NVE switch behind which the MAC is located.
The same is not true for IP multicast traffic. Such traffic is simply
flooded as BUM to all NVE switches in the broadcast domain (BD),
regardless if a switch has interested receivers for the multicast stream
or not. This is especially problematic for overlay networks that make
heavy use of multicast.
The issue is addressed by RFC 9251 [7] that defines a "Selective
Multicast Ethernet Tag Route" (type 6) [8] which allows NVE switches in
the EVPN network to advertise multicast streams that they are interested
in. This is done by having each switch suppress IGMP/MLD packets from
being transmitted to the NVE network and instead communicate the
information over BGP to other switches.
As far as the bridge driver is concerned, the above means that the
multicast state (i.e., {multicast address, group timer, filter-mode,
(source records)}) for the VXLAN bridge port is not populated by the
kernel from snooped IGMP/MLD packets (they are suppressed), but instead
by user space. Specifically, by the routing daemon that is exchanging
EVPN routes with other NVE switches.
Changes are obviously also required in the VXLAN driver, but they are
the subject of future patchsets. See the "Future work" section.
Implementation
=============
The user interface is extended to allow user space to specify the filter
mode of the MDB port group entry and its source list. Replace support is
also added so that user space would not need to remove an entry and
re-add it only to edit its source list or filter mode, as that would
result in packet loss. Example usage:
# bridge mdb replace dev br0 port dummy10 grp 239.1.1.1 permanent \
source_list 192.0.2.1,192.0.2.3 filter_mode exclude proto zebra
# bridge -d -s mdb show
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.3 permanent filter_mode include
proto zebra blocked 0.00
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent filter_mode include
proto zebra blocked 0.00
dev br0 port dummy10 grp 239.1.1.1 permanent filter_mode exclude source_list
192.0.2.3/0.00,192.0.2.1/0.00 proto zebra 0.00
The netlink interface is extended with a few new attributes in the
RTM_NEWMDB request message:
[ struct nlmsghdr ]
[ struct br_port_msg ]
[ MDBA_SET_ENTRY ]
struct br_mdb_entry
[ MDBA_SET_ENTRY_ATTRS ]
[ MDBE_ATTR_SOURCE ]
struct in_addr / struct in6_addr
[ MDBE_ATTR_SRC_LIST ] // new
[ MDBE_SRC_LIST_ENTRY ]
[ MDBE_SRCATTR_ADDRESS ]
struct in_addr / struct in6_addr
[ ...]
[ MDBE_ATTR_GROUP_MODE ] // new
u8
[ MDBE_ATTR_RTPORT ] // new
u8
No changes are required in RTM_NEWMDB responses and notifications, as
all the information can already be dumped by the kernel today.
Testing
======
Tested with existing bridge multicast selftests: bridge_igmp.sh,
bridge_mdb_port_down.sh, bridge_mdb.sh, bridge_mld.sh,
bridge_vlan_mcast.sh.
In addition, added many new test cases for existing as well as for new
MDB functionality.
Patchset overview
================
Patches #1-#8 are non-functional preparations for the core changes in
later patches.
Patches #9-#10 allow user space to install (*, G) entries with a source
list and associated filter mode. Specifically, patch #9 adds the
necessary kernel plumbing and patch #10 exposes the new functionality to
user space via a few new attributes.
Patch #11 allows user space to specify the routing protocol of new MDB
port group entries so that a routing daemon could differentiate between
entries installed by it and those installed by an administrator.
Patch #12 allows user space to replace MDB port group entries. This is
useful, for example, when user space wants to add a new source to a
source list. Instead of deleting a (*, G) entry and re-adding it with an
extended source list (which would result in packet loss), user space can
simply replace the current entry.
Patches #13-#14 add tests for existing MDB functionality as well as for
all new functionality added in this patchset.
Future work
==========
The VXLAN driver will need to be extended with an MDB so that it could
selectively forward IP multicast traffic to NVE switches with interested
receivers instead of simply flooding it to all switches as BUM.
The idea is to reuse the existing MDB interface for the VXLAN driver in
a similar way to how the FDB interface is shared between the bridge and
VXLAN drivers.
>From command line perspective, configuration will look as follows:
# bridge mdb add dev br0 port vxlan0 grp 239.1.1.1 permanent \
filter_mode exclude source_list 198.50.100.1,198.50.100.2
# bridge mdb add dev vxlan0 port vxlan0 grp 239.1.1.1 permanent \
filter_mode include source_list 198.50.100.3,198.50.100.4 \
dst 192.0.2.1 dst_port 4789 src_vni 2
# bridge mdb add dev vxlan0 port vxlan0 grp 239.1.1.1 permanent \
filter_mode exclude source_list 198.50.100.1,198.50.100.2 \
dst 192.0.2.2 dst_port 4789 src_vni 2
Where the first command is enabled by this set, but the next two will be
the subject of future work.
>From netlink perspective, the existing PF_BRIDGE/RTM_*MDB messages will
be extended to the VXLAN driver. This means that a few new attributes
will be added (e.g., 'MDBE_ATTR_SRC_VNI') and that the handlers for
these messages will need to move to net/core/rtnetlink.c. The rtnetlink
code will call into the appropriate driver based on the ifindex
specified in the ancillary header.
iproute2 patches can be found here [9].
Changelog
========
Since RFC [10]:
* Patch #6: New patch.
* Patch #9: Use an array instead of a list to store source entries.
* Patch #10: Use an array instead of list to store source entries.
* Patch #10: Drop br_mdb_config_attrs_fini().
* Patch #11: Reject protocol for host entries.
* Patch #13: New patch.
* Patch #14: New patch.
[1] https://datatracker.ietf.org/doc/html/rfc3376
[2] https://www.rfc-editor.org/rfc/rfc3810
[3]
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=6af52ae2ed14a6bc756d5606b29097dfd76740b8
[4]
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=68d4fd30c83b1b208e08c954cd45e6474b148c87
[5] https://datatracker.ietf.org/doc/html/rfc7432
[6] https://datatracker.ietf.org/doc/html/rfc7432#section-7.2
[7] https://datatracker.ietf.org/doc/html/rfc9251
[8] https://datatracker.ietf.org/doc/html/rfc9251#section-9.1
[9] https://github.com/idosch/iproute2/commits/submit/mdb_v1
[10] https://lore.kernel.org/netdev/20221018120420.561846-1-idosch at
nvidia.com/
Ido Schimmel (14):
bridge: mcast: Do not derive entry type from its filter mode
bridge: mcast: Split (*, G) and (S, G) addition into different
functions
bridge: mcast: Place netlink policy before validation functions
bridge: mcast: Add a centralized error path
bridge: mcast: Expose br_multicast_new_group_src()
bridge: mcast: Expose __br_multicast_del_group_src()
bridge: mcast: Add a flag for user installed source entries
bridge: mcast: Avoid arming group timer when (S, G) corresponds to a
source
bridge: mcast: Add support for (*, G) with a source list and filter
mode
bridge: mcast: Allow user space to add (*, G) with a source list and
filter mode
bridge: mcast: Allow user space to specify MDB entry routing protocol
bridge: mcast: Support replacement of MDB port group entries
selftests: forwarding: Rename bridge_mdb test
selftests: forwarding: Add bridge MDB test
include/uapi/linux/if_bridge.h | 21 +
net/bridge/br_mdb.c | 526 +++++++-
net/bridge/br_multicast.c | 16 +-
net/bridge/br_private.h | 15 +
.../testing/selftests/net/forwarding/Makefile | 1 +
.../selftests/net/forwarding/bridge_mdb.sh | 1127 ++++++++++++++++-
.../net/forwarding/bridge_mdb_host.sh | 103 ++
7 files changed, 1709 insertions(+), 100 deletions(-)
create mode 100755 tools/testing/selftests/net/forwarding/bridge_mdb_host.sh
--
2.37.3
Ido Schimmel
2022-Dec-08 15:28 UTC
[Bridge] [PATCH net-next 01/14] bridge: mcast: Do not derive entry type from its filter mode
Currently, the filter mode (i.e., INCLUDE / EXCLUDE) of MDB entries
cannot be set from user space. Instead, it is set by the kernel
according to the entry type: (*, G) entries are treated as EXCLUDE and
(S, G) entries are treated as INCLUDE. This allows the kernel to derive
the entry type from its filter mode.
Subsequent patches will allow user space to set the filter mode of (*,
G) entries, making the current assumption incorrect.
As a preparation, remove the current assumption and instead determine
the entry type from its key, which is a more direct way.
Signed-off-by: Ido Schimmel <idosch at nvidia.com>
---
net/bridge/br_mdb.c | 9 +++------
1 file changed, 3 insertions(+), 6 deletions(-)
diff --git a/net/bridge/br_mdb.c b/net/bridge/br_mdb.c
index ae7d93c08880..2b6921dbdc02 100644
--- a/net/bridge/br_mdb.c
+++ b/net/bridge/br_mdb.c
@@ -857,17 +857,14 @@ static int br_mdb_add_group(const struct br_mdb_config
*cfg,
* added to it for proper replication
*/
if (br_multicast_should_handle_mode(brmctx, group.proto)) {
- switch (filter_mode) {
- case MCAST_EXCLUDE:
- br_multicast_star_g_handle_mode(p, MCAST_EXCLUDE);
- break;
- case MCAST_INCLUDE:
+ if (br_multicast_is_star_g(&group)) {
+ br_multicast_star_g_handle_mode(p, filter_mode);
+ } else {
star_group = p->key.addr;
memset(&star_group.src, 0, sizeof(star_group.src));
star_mp = br_mdb_ip_get(br, &star_group);
if (star_mp)
br_multicast_sg_add_exclude_ports(star_mp, p);
- break;
}
}
--
2.37.3
Ido Schimmel
2022-Dec-08 15:28 UTC
[Bridge] [PATCH net-next 02/14] bridge: mcast: Split (*, G) and (S, G) addition into different functions
When the bridge is using IGMP version 3 or MLD version 2, it handles the
addition of (*, G) and (S, G) entries differently.
When a new (S, G) port group entry is added, all the (*, G) EXCLUDE
ports need to be added to the port group of the new entry. Similarly,
when a new (*, G) EXCLUDE port group entry is added, the port needs to
be added to the port group of all the matching (S, G) entries.
Subsequent patches will create more differences between both entry
types. Namely, filter mode and source list can only be specified for (*,
G) entries.
Given the current and future differences between both entry types,
handle the addition of each entry type in a different function, thereby
avoiding the creation of one complex function.
Signed-off-by: Ido Schimmel <idosch at nvidia.com>
---
net/bridge/br_mdb.c | 145 +++++++++++++++++++++++++++++---------------
1 file changed, 96 insertions(+), 49 deletions(-)
diff --git a/net/bridge/br_mdb.c b/net/bridge/br_mdb.c
index 2b6921dbdc02..e3bd2122d559 100644
--- a/net/bridge/br_mdb.c
+++ b/net/bridge/br_mdb.c
@@ -786,21 +786,107 @@ __br_mdb_choose_context(struct net_bridge *br,
return brmctx;
}
+static int br_mdb_add_group_sg(const struct br_mdb_config *cfg,
+ struct net_bridge_mdb_entry *mp,
+ struct net_bridge_mcast *brmctx,
+ unsigned char flags,
+ struct netlink_ext_ack *extack)
+{
+ struct net_bridge_port_group __rcu **pp;
+ struct net_bridge_port_group *p;
+ unsigned long now = jiffies;
+
+ for (pp = &mp->ports;
+ (p = mlock_dereference(*pp, cfg->br)) != NULL;
+ pp = &p->next) {
+ if (p->key.port == cfg->p) {
+ NL_SET_ERR_MSG_MOD(extack, "(S, G) group is already joined by
port");
+ return -EEXIST;
+ }
+ if ((unsigned long)p->key.port < (unsigned long)cfg->p)
+ break;
+ }
+
+ p = br_multicast_new_port_group(cfg->p, &cfg->group, *pp, flags,
NULL,
+ MCAST_INCLUDE, RTPROT_STATIC);
+ if (unlikely(!p)) {
+ NL_SET_ERR_MSG_MOD(extack, "Couldn't allocate new (S, G) port
group");
+ return -ENOMEM;
+ }
+ rcu_assign_pointer(*pp, p);
+ if (!(flags & MDB_PG_FLAGS_PERMANENT))
+ mod_timer(&p->timer,
+ now + brmctx->multicast_membership_interval);
+ br_mdb_notify(cfg->br->dev, mp, p, RTM_NEWMDB);
+
+ /* All of (*, G) EXCLUDE ports need to be added to the new (S, G) for
+ * proper replication.
+ */
+ if (br_multicast_should_handle_mode(brmctx, cfg->group.proto)) {
+ struct net_bridge_mdb_entry *star_mp;
+ struct br_ip star_group;
+
+ star_group = p->key.addr;
+ memset(&star_group.src, 0, sizeof(star_group.src));
+ star_mp = br_mdb_ip_get(cfg->br, &star_group);
+ if (star_mp)
+ br_multicast_sg_add_exclude_ports(star_mp, p);
+ }
+
+ return 0;
+}
+
+static int br_mdb_add_group_star_g(const struct br_mdb_config *cfg,
+ struct net_bridge_mdb_entry *mp,
+ struct net_bridge_mcast *brmctx,
+ unsigned char flags,
+ struct netlink_ext_ack *extack)
+{
+ struct net_bridge_port_group __rcu **pp;
+ struct net_bridge_port_group *p;
+ unsigned long now = jiffies;
+
+ for (pp = &mp->ports;
+ (p = mlock_dereference(*pp, cfg->br)) != NULL;
+ pp = &p->next) {
+ if (p->key.port == cfg->p) {
+ NL_SET_ERR_MSG_MOD(extack, "(*, G) group is already joined by
port");
+ return -EEXIST;
+ }
+ if ((unsigned long)p->key.port < (unsigned long)cfg->p)
+ break;
+ }
+
+ p = br_multicast_new_port_group(cfg->p, &cfg->group, *pp, flags,
NULL,
+ MCAST_EXCLUDE, RTPROT_STATIC);
+ if (unlikely(!p)) {
+ NL_SET_ERR_MSG_MOD(extack, "Couldn't allocate new (*, G) port
group");
+ return -ENOMEM;
+ }
+ rcu_assign_pointer(*pp, p);
+ if (!(flags & MDB_PG_FLAGS_PERMANENT))
+ mod_timer(&p->timer,
+ now + brmctx->multicast_membership_interval);
+ br_mdb_notify(cfg->br->dev, mp, p, RTM_NEWMDB);
+ /* If we are adding a new EXCLUDE port group (*, G), it needs to be
+ * also added to all (S, G) entries for proper replication.
+ */
+ if (br_multicast_should_handle_mode(brmctx, cfg->group.proto))
+ br_multicast_star_g_handle_mode(p, MCAST_EXCLUDE);
+
+ return 0;
+}
+
static int br_mdb_add_group(const struct br_mdb_config *cfg,
struct netlink_ext_ack *extack)
{
- struct net_bridge_mdb_entry *mp, *star_mp;
- struct net_bridge_port_group __rcu **pp;
struct br_mdb_entry *entry = cfg->entry;
struct net_bridge_port *port = cfg->p;
+ struct net_bridge_mdb_entry *mp;
struct net_bridge *br = cfg->br;
- struct net_bridge_port_group *p;
struct net_bridge_mcast *brmctx;
struct br_ip group = cfg->group;
- unsigned long now = jiffies;
unsigned char flags = 0;
- struct br_ip star_group;
- u8 filter_mode;
brmctx = __br_mdb_choose_context(br, entry, extack);
if (!brmctx)
@@ -823,52 +909,13 @@ static int br_mdb_add_group(const struct br_mdb_config
*cfg,
return 0;
}
- for (pp = &mp->ports;
- (p = mlock_dereference(*pp, br)) != NULL;
- pp = &p->next) {
- if (p->key.port == port) {
- NL_SET_ERR_MSG_MOD(extack, "Group is already joined by port");
- return -EEXIST;
- }
- if ((unsigned long)p->key.port < (unsigned long)port)
- break;
- }
-
- filter_mode = br_multicast_is_star_g(&group) ? MCAST_EXCLUDE :
- MCAST_INCLUDE;
-
if (entry->state == MDB_PERMANENT)
flags |= MDB_PG_FLAGS_PERMANENT;
- p = br_multicast_new_port_group(port, &group, *pp, flags, NULL,
- filter_mode, RTPROT_STATIC);
- if (unlikely(!p)) {
- NL_SET_ERR_MSG_MOD(extack, "Couldn't allocate new port group");
- return -ENOMEM;
- }
- rcu_assign_pointer(*pp, p);
- if (entry->state == MDB_TEMPORARY)
- mod_timer(&p->timer,
- now + brmctx->multicast_membership_interval);
- br_mdb_notify(br->dev, mp, p, RTM_NEWMDB);
- /* if we are adding a new EXCLUDE port group (*,G) it needs to be also
- * added to all S,G entries for proper replication, if we are adding
- * a new INCLUDE port (S,G) then all of *,G EXCLUDE ports need to be
- * added to it for proper replication
- */
- if (br_multicast_should_handle_mode(brmctx, group.proto)) {
- if (br_multicast_is_star_g(&group)) {
- br_multicast_star_g_handle_mode(p, filter_mode);
- } else {
- star_group = p->key.addr;
- memset(&star_group.src, 0, sizeof(star_group.src));
- star_mp = br_mdb_ip_get(br, &star_group);
- if (star_mp)
- br_multicast_sg_add_exclude_ports(star_mp, p);
- }
- }
-
- return 0;
+ if (br_multicast_is_star_g(&group))
+ return br_mdb_add_group_star_g(cfg, mp, brmctx, flags, extack);
+ else
+ return br_mdb_add_group_sg(cfg, mp, brmctx, flags, extack);
}
static int __br_mdb_add(const struct br_mdb_config *cfg,
--
2.37.3
Ido Schimmel
2022-Dec-08 15:28 UTC
[Bridge] [PATCH net-next 03/14] bridge: mcast: Place netlink policy before validation functions
Subsequent patches are going to add additional validation functions and
netlink policies. Some of these functions will need to perform parsing
using nla_parse_nested() and the new policies.
In order to keep all the policies next to each other, move the current
policy to before the validation functions.
Signed-off-by: Ido Schimmel <idosch at nvidia.com>
---
net/bridge/br_mdb.c | 12 ++++++------
1 file changed, 6 insertions(+), 6 deletions(-)
diff --git a/net/bridge/br_mdb.c b/net/bridge/br_mdb.c
index e3bd2122d559..fcdd464cf997 100644
--- a/net/bridge/br_mdb.c
+++ b/net/bridge/br_mdb.c
@@ -663,6 +663,12 @@ void br_rtr_notify(struct net_device *dev, struct
net_bridge_mcast_port *pmctx,
rtnl_set_sk_err(net, RTNLGRP_MDB, err);
}
+static const struct nla_policy br_mdbe_attrs_pol[MDBE_ATTR_MAX + 1] = {
+ [MDBE_ATTR_SOURCE] = NLA_POLICY_RANGE(NLA_BINARY,
+ sizeof(struct in_addr),
+ sizeof(struct in6_addr)),
+};
+
static bool is_valid_mdb_entry(struct br_mdb_entry *entry,
struct netlink_ext_ack *extack)
{
@@ -748,12 +754,6 @@ static bool is_valid_mdb_source(struct nlattr *attr, __be16
proto,
return true;
}
-static const struct nla_policy br_mdbe_attrs_pol[MDBE_ATTR_MAX + 1] = {
- [MDBE_ATTR_SOURCE] = NLA_POLICY_RANGE(NLA_BINARY,
- sizeof(struct in_addr),
- sizeof(struct in6_addr)),
-};
-
static struct net_bridge_mcast *
__br_mdb_choose_context(struct net_bridge *br,
const struct br_mdb_entry *entry,
--
2.37.3
Ido Schimmel
2022-Dec-08 15:28 UTC
[Bridge] [PATCH net-next 04/14] bridge: mcast: Add a centralized error path
Subsequent patches will add memory allocations in br_mdb_config_init()
as the MDB configuration structure will include a linked list of source
entries. This memory will need to be freed regardless if br_mdb_add()
succeeded or failed.
As a preparation for this change, add a centralized error path where the
memory will be freed.
Note that br_mdb_del() already has one error path and therefore does not
require any changes.
Signed-off-by: Ido Schimmel <idosch at nvidia.com>
---
net/bridge/br_mdb.c | 10 ++++++----
1 file changed, 6 insertions(+), 4 deletions(-)
diff --git a/net/bridge/br_mdb.c b/net/bridge/br_mdb.c
index fcdd464cf997..95780652cdbf 100644
--- a/net/bridge/br_mdb.c
+++ b/net/bridge/br_mdb.c
@@ -1053,28 +1053,29 @@ static int br_mdb_add(struct sk_buff *skb, struct
nlmsghdr *nlh,
if (err)
return err;
+ err = -EINVAL;
/* host join errors which can happen before creating the group */
if (!cfg.p && !br_group_is_l2(&cfg.group)) {
/* don't allow any flags for host-joined IP groups */
if (cfg.entry->state) {
NL_SET_ERR_MSG_MOD(extack, "Flags are not allowed for host
groups");
- return -EINVAL;
+ goto out;
}
if (!br_multicast_is_star_g(&cfg.group)) {
NL_SET_ERR_MSG_MOD(extack, "Groups with sources cannot be manually host
joined");
- return -EINVAL;
+ goto out;
}
}
if (br_group_is_l2(&cfg.group) && cfg.entry->state !=
MDB_PERMANENT) {
NL_SET_ERR_MSG_MOD(extack, "Only permanent L2 entries allowed");
- return -EINVAL;
+ goto out;
}
if (cfg.p) {
if (cfg.p->state == BR_STATE_DISABLED && cfg.entry->state !=
MDB_PERMANENT) {
NL_SET_ERR_MSG_MOD(extack, "Port is in disabled state and entry is not
permanent");
- return -EINVAL;
+ goto out;
}
vg = nbp_vlan_group(cfg.p);
} else {
@@ -1096,6 +1097,7 @@ static int br_mdb_add(struct sk_buff *skb, struct nlmsghdr
*nlh,
err = __br_mdb_add(&cfg, extack);
}
+out:
return err;
}
--
2.37.3
Ido Schimmel
2022-Dec-08 15:28 UTC
[Bridge] [PATCH net-next 05/14] bridge: mcast: Expose br_multicast_new_group_src()
Currently, new group source entries are only created in response to
received Membership Reports. Subsequent patches are going to allow user
space to install (*, G) entries with a source list.
As a preparatory step, expose br_multicast_new_group_src() so that it
could later be invoked from the MDB code (i.e., br_mdb.c) that handles
RTM_NEWMDB messages.
Signed-off-by: Ido Schimmel <idosch at nvidia.com>
---
net/bridge/br_multicast.c | 2 +-
net/bridge/br_private.h | 3 +++
2 files changed, 4 insertions(+), 1 deletion(-)
diff --git a/net/bridge/br_multicast.c b/net/bridge/br_multicast.c
index db4c3900ae95..b2bc23fdcee5 100644
--- a/net/bridge/br_multicast.c
+++ b/net/bridge/br_multicast.c
@@ -1232,7 +1232,7 @@ br_multicast_find_group_src(struct net_bridge_port_group
*pg, struct br_ip *ip)
return NULL;
}
-static struct net_bridge_group_src *
+struct net_bridge_group_src *
br_multicast_new_group_src(struct net_bridge_port_group *pg, struct br_ip
*src_ip)
{
struct net_bridge_group_src *grp_src;
diff --git a/net/bridge/br_private.h b/net/bridge/br_private.h
index 3997e16c15fc..183de6c57d72 100644
--- a/net/bridge/br_private.h
+++ b/net/bridge/br_private.h
@@ -974,6 +974,9 @@ void br_multicast_sg_add_exclude_ports(struct
net_bridge_mdb_entry *star_mp,
struct net_bridge_port_group *sg);
struct net_bridge_group_src *
br_multicast_find_group_src(struct net_bridge_port_group *pg, struct br_ip
*ip);
+struct net_bridge_group_src *
+br_multicast_new_group_src(struct net_bridge_port_group *pg,
+ struct br_ip *src_ip);
void br_multicast_del_group_src(struct net_bridge_group_src *src,
bool fastleave);
void br_multicast_ctx_init(struct net_bridge *br,
--
2.37.3
Ido Schimmel
2022-Dec-08 15:28 UTC
[Bridge] [PATCH net-next 06/14] bridge: mcast: Expose __br_multicast_del_group_src()
Expose __br_multicast_del_group_src() which is symmetric to
br_multicast_new_group_src() and does not remove the installed {S, G}
forwarding entry, unlike br_multicast_del_group_src().
The function will be used in the error path when user space was able to
add a new source entry, but failed to install a corresponding forwarding
entry.
Signed-off-by: Ido Schimmel <idosch at nvidia.com>
---
Notes:
v1:
* New patch.
net/bridge/br_multicast.c | 11 ++++++++---
net/bridge/br_private.h | 1 +
2 files changed, 9 insertions(+), 3 deletions(-)
diff --git a/net/bridge/br_multicast.c b/net/bridge/br_multicast.c
index b2bc23fdcee5..8432b4ea7f28 100644
--- a/net/bridge/br_multicast.c
+++ b/net/bridge/br_multicast.c
@@ -650,18 +650,23 @@ static void br_multicast_destroy_group_src(struct
net_bridge_mcast_gc *gc)
kfree_rcu(src, rcu);
}
-void br_multicast_del_group_src(struct net_bridge_group_src *src,
- bool fastleave)
+void __br_multicast_del_group_src(struct net_bridge_group_src *src)
{
struct net_bridge *br = src->pg->key.port->br;
- br_multicast_fwd_src_remove(src, fastleave);
hlist_del_init_rcu(&src->node);
src->pg->src_ents--;
hlist_add_head(&src->mcast_gc.gc_node, &br->mcast_gc_list);
queue_work(system_long_wq, &br->mcast_gc_work);
}
+void br_multicast_del_group_src(struct net_bridge_group_src *src,
+ bool fastleave)
+{
+ br_multicast_fwd_src_remove(src, fastleave);
+ __br_multicast_del_group_src(src);
+}
+
static void br_multicast_destroy_port_group(struct net_bridge_mcast_gc *gc)
{
struct net_bridge_port_group *pg;
diff --git a/net/bridge/br_private.h b/net/bridge/br_private.h
index 183de6c57d72..a3db99d79a3d 100644
--- a/net/bridge/br_private.h
+++ b/net/bridge/br_private.h
@@ -977,6 +977,7 @@ br_multicast_find_group_src(struct net_bridge_port_group
*pg, struct br_ip *ip);
struct net_bridge_group_src *
br_multicast_new_group_src(struct net_bridge_port_group *pg,
struct br_ip *src_ip);
+void __br_multicast_del_group_src(struct net_bridge_group_src *src);
void br_multicast_del_group_src(struct net_bridge_group_src *src,
bool fastleave);
void br_multicast_ctx_init(struct net_bridge *br,
--
2.37.3
Ido Schimmel
2022-Dec-08 15:28 UTC
[Bridge] [PATCH net-next 07/14] bridge: mcast: Add a flag for user installed source entries
There are a few places where the bridge driver differentiates between
(S, G) entries installed by the kernel (in response to Membership
Reports) and those installed by user space. One of them is when deleting
an (S, G) entry corresponding to a source entry that is being deleted.
While user space cannot currently add a source entry to a (*, G), it can
add an (S, G) entry that later corresponds to a source entry created by
the reception of a Membership Report. If this source entry is later
deleted because its source timer expired or because the (*, G) entry is
being deleted, the bridge driver will not delete the corresponding (S,
G) entry if it was added by user space as permanent.
This is going to be a problem when the ability to install a (*, G) with
a source list is exposed to user space. In this case, when user space
installs the (*, G) as permanent, then all the (S, G) entries
corresponding to its source list will also be installed as permanent.
When user space deletes the (*, G), all the source entries will be
deleted and the expectation is that the corresponding (S, G) entries
will be deleted as well.
Solve this by introducing a new source entry flag denoting that the
entry was installed by user space. When the entry is deleted, delete the
corresponding (S, G) entry even if it was installed by user space as
permanent, as the flag tells us that it was installed in response to the
source entry being created.
The flag will be set in a subsequent patch where source entries are
created in response to user requests.
Signed-off-by: Ido Schimmel <idosch at nvidia.com>
---
net/bridge/br_multicast.c | 3 ++-
net/bridge/br_private.h | 1 +
2 files changed, 3 insertions(+), 1 deletion(-)
diff --git a/net/bridge/br_multicast.c b/net/bridge/br_multicast.c
index 8432b4ea7f28..48170bd3785e 100644
--- a/net/bridge/br_multicast.c
+++ b/net/bridge/br_multicast.c
@@ -552,7 +552,8 @@ static void br_multicast_fwd_src_remove(struct
net_bridge_group_src *src,
continue;
if (p->rt_protocol != RTPROT_KERNEL &&
- (p->flags & MDB_PG_FLAGS_PERMANENT))
+ (p->flags & MDB_PG_FLAGS_PERMANENT) &&
+ !(src->flags & BR_SGRP_F_USER_ADDED))
break;
if (fastleave)
diff --git a/net/bridge/br_private.h b/net/bridge/br_private.h
index a3db99d79a3d..74f17b56c9eb 100644
--- a/net/bridge/br_private.h
+++ b/net/bridge/br_private.h
@@ -300,6 +300,7 @@ struct net_bridge_fdb_flush_desc {
#define BR_SGRP_F_DELETE BIT(0)
#define BR_SGRP_F_SEND BIT(1)
#define BR_SGRP_F_INSTALLED BIT(2)
+#define BR_SGRP_F_USER_ADDED BIT(3)
struct net_bridge_mcast_gc {
struct hlist_node gc_node;
--
2.37.3
Ido Schimmel
2022-Dec-08 15:28 UTC
[Bridge] [PATCH net-next 08/14] bridge: mcast: Avoid arming group timer when (S, G) corresponds to a source
User space will soon be able to install a (*, G) with a source list,
prompting the creation of a (S, G) entry for each source.
In this case, the group timer of the (S, G) entry should never be set.
Solve this by adding a new field to the MDB configuration structure that
denotes whether the (S, G) corresponds to a source or not.
The field will be set in a subsequent patch where br_mdb_add_group_sg()
is called in order to create a (S, G) entry for each user provided
source.
Signed-off-by: Ido Schimmel <idosch at nvidia.com>
---
net/bridge/br_mdb.c | 2 +-
net/bridge/br_private.h | 1 +
2 files changed, 2 insertions(+), 1 deletion(-)
diff --git a/net/bridge/br_mdb.c b/net/bridge/br_mdb.c
index 95780652cdbf..7cda9d1c5c93 100644
--- a/net/bridge/br_mdb.c
+++ b/net/bridge/br_mdb.c
@@ -814,7 +814,7 @@ static int br_mdb_add_group_sg(const struct br_mdb_config
*cfg,
return -ENOMEM;
}
rcu_assign_pointer(*pp, p);
- if (!(flags & MDB_PG_FLAGS_PERMANENT))
+ if (!(flags & MDB_PG_FLAGS_PERMANENT) && !cfg->src_entry)
mod_timer(&p->timer,
now + brmctx->multicast_membership_interval);
br_mdb_notify(cfg->br->dev, mp, p, RTM_NEWMDB);
diff --git a/net/bridge/br_private.h b/net/bridge/br_private.h
index 74f17b56c9eb..e98bfe3c02e1 100644
--- a/net/bridge/br_private.h
+++ b/net/bridge/br_private.h
@@ -98,6 +98,7 @@ struct br_mdb_config {
struct net_bridge_port *p;
struct br_mdb_entry *entry;
struct br_ip group;
+ bool src_entry;
};
#endif
--
2.37.3
Ido Schimmel
2022-Dec-08 15:28 UTC
[Bridge] [PATCH net-next 09/14] bridge: mcast: Add support for (*, G) with a source list and filter mode
In preparation for allowing user space to add (*, G) entries with a
source list and associated filter mode, add the necessary plumbing to
handle such requests.
Extend the MDB configuration structure with a currently empty source
array and filter mode that is currently hard coded to EXCLUDE.
Add the source entries and the corresponding (S, G) entries before
making the new (*, G) port group entry visible to the data path.
Handle the creation of each source entry in a similar fashion to how it
is created from the data path in response to received Membership
Reports: Create the source entry, arm the source timer (if needed), add
a corresponding (S, G) forwarding entry and finally mark the source
entry as installed (by user space).
Add the (S, G) entry by populating an MDB configuration structure and
calling br_mdb_add_group_sg() as if a new entry is created by user
space, with the sole difference that the 'src_entry' field is set to
make sure that the group timer of such entries is never armed.
Note that it is not currently possible to add more than 32 source
entries to a port group entry. If this proves to be a problem we can
either increase 'PG_SRC_ENT_LIMIT' or avoid forcing a limit on entries
created by user space.
Signed-off-by: Ido Schimmel <idosch at nvidia.com>
---
Notes:
v1:
* Use an array instead of a list to store source entries.
net/bridge/br_mdb.c | 128 +++++++++++++++++++++++++++++++++++++++-
net/bridge/br_private.h | 7 +++
2 files changed, 132 insertions(+), 3 deletions(-)
diff --git a/net/bridge/br_mdb.c b/net/bridge/br_mdb.c
index 7cda9d1c5c93..e9a4b7e247e7 100644
--- a/net/bridge/br_mdb.c
+++ b/net/bridge/br_mdb.c
@@ -836,6 +836,114 @@ static int br_mdb_add_group_sg(const struct br_mdb_config
*cfg,
return 0;
}
+static int br_mdb_add_group_src_fwd(const struct br_mdb_config *cfg,
+ struct br_ip *src_ip,
+ struct net_bridge_mcast *brmctx,
+ struct netlink_ext_ack *extack)
+{
+ struct net_bridge_mdb_entry *sgmp;
+ struct br_mdb_config sg_cfg;
+ struct br_ip sg_ip;
+ u8 flags = 0;
+
+ sg_ip = cfg->group;
+ sg_ip.src = src_ip->src;
+ sgmp = br_multicast_new_group(cfg->br, &sg_ip);
+ if (IS_ERR(sgmp)) {
+ NL_SET_ERR_MSG_MOD(extack, "Failed to add (S, G) MDB entry");
+ return PTR_ERR(sgmp);
+ }
+
+ if (cfg->entry->state == MDB_PERMANENT)
+ flags |= MDB_PG_FLAGS_PERMANENT;
+ if (cfg->filter_mode == MCAST_EXCLUDE)
+ flags |= MDB_PG_FLAGS_BLOCKED;
+
+ memset(&sg_cfg, 0, sizeof(sg_cfg));
+ sg_cfg.br = cfg->br;
+ sg_cfg.p = cfg->p;
+ sg_cfg.entry = cfg->entry;
+ sg_cfg.group = sg_ip;
+ sg_cfg.src_entry = true;
+ sg_cfg.filter_mode = MCAST_INCLUDE;
+ return br_mdb_add_group_sg(&sg_cfg, sgmp, brmctx, flags, extack);
+}
+
+static int br_mdb_add_group_src(const struct br_mdb_config *cfg,
+ struct net_bridge_port_group *pg,
+ struct net_bridge_mcast *brmctx,
+ struct br_mdb_src_entry *src,
+ struct netlink_ext_ack *extack)
+{
+ struct net_bridge_group_src *ent;
+ unsigned long now = jiffies;
+ int err;
+
+ ent = br_multicast_find_group_src(pg, &src->addr);
+ if (!ent) {
+ ent = br_multicast_new_group_src(pg, &src->addr);
+ if (!ent) {
+ NL_SET_ERR_MSG_MOD(extack, "Failed to add new source entry");
+ return -ENOSPC;
+ }
+ } else {
+ NL_SET_ERR_MSG_MOD(extack, "Source entry already exists");
+ return -EEXIST;
+ }
+
+ if (cfg->filter_mode == MCAST_INCLUDE &&
+ cfg->entry->state == MDB_TEMPORARY)
+ mod_timer(&ent->timer, now + br_multicast_gmi(brmctx));
+ else
+ del_timer(&ent->timer);
+
+ /* Install a (S, G) forwarding entry for the source. */
+ err = br_mdb_add_group_src_fwd(cfg, &src->addr, brmctx, extack);
+ if (err)
+ goto err_del_sg;
+
+ ent->flags = BR_SGRP_F_INSTALLED | BR_SGRP_F_USER_ADDED;
+
+ return 0;
+
+err_del_sg:
+ __br_multicast_del_group_src(ent);
+ return err;
+}
+
+static void br_mdb_del_group_src(struct net_bridge_port_group *pg,
+ struct br_mdb_src_entry *src)
+{
+ struct net_bridge_group_src *ent;
+
+ ent = br_multicast_find_group_src(pg, &src->addr);
+ if (WARN_ON_ONCE(!ent))
+ return;
+ br_multicast_del_group_src(ent, false);
+}
+
+static int br_mdb_add_group_srcs(const struct br_mdb_config *cfg,
+ struct net_bridge_port_group *pg,
+ struct net_bridge_mcast *brmctx,
+ struct netlink_ext_ack *extack)
+{
+ int i, err;
+
+ for (i = 0; i < cfg->num_src_entries; i++) {
+ err = br_mdb_add_group_src(cfg, pg, brmctx,
+ &cfg->src_entries[i], extack);
+ if (err)
+ goto err_del_group_srcs;
+ }
+
+ return 0;
+
+err_del_group_srcs:
+ for (i--; i >= 0; i--)
+ br_mdb_del_group_src(pg, &cfg->src_entries[i]);
+ return err;
+}
+
static int br_mdb_add_group_star_g(const struct br_mdb_config *cfg,
struct net_bridge_mdb_entry *mp,
struct net_bridge_mcast *brmctx,
@@ -845,6 +953,7 @@ static int br_mdb_add_group_star_g(const struct
br_mdb_config *cfg,
struct net_bridge_port_group __rcu **pp;
struct net_bridge_port_group *p;
unsigned long now = jiffies;
+ int err;
for (pp = &mp->ports;
(p = mlock_dereference(*pp, cfg->br)) != NULL;
@@ -858,23 +967,35 @@ static int br_mdb_add_group_star_g(const struct
br_mdb_config *cfg,
}
p = br_multicast_new_port_group(cfg->p, &cfg->group, *pp, flags,
NULL,
- MCAST_EXCLUDE, RTPROT_STATIC);
+ cfg->filter_mode, RTPROT_STATIC);
if (unlikely(!p)) {
NL_SET_ERR_MSG_MOD(extack, "Couldn't allocate new (*, G) port
group");
return -ENOMEM;
}
+
+ err = br_mdb_add_group_srcs(cfg, p, brmctx, extack);
+ if (err)
+ goto err_del_port_group;
+
rcu_assign_pointer(*pp, p);
- if (!(flags & MDB_PG_FLAGS_PERMANENT))
+ if (!(flags & MDB_PG_FLAGS_PERMANENT) &&
+ cfg->filter_mode == MCAST_EXCLUDE)
mod_timer(&p->timer,
now + brmctx->multicast_membership_interval);
br_mdb_notify(cfg->br->dev, mp, p, RTM_NEWMDB);
/* If we are adding a new EXCLUDE port group (*, G), it needs to be
* also added to all (S, G) entries for proper replication.
*/
- if (br_multicast_should_handle_mode(brmctx, cfg->group.proto))
+ if (br_multicast_should_handle_mode(brmctx, cfg->group.proto) &&
+ cfg->filter_mode == MCAST_EXCLUDE)
br_multicast_star_g_handle_mode(p, MCAST_EXCLUDE);
return 0;
+
+err_del_port_group:
+ hlist_del_init(&p->mglist);
+ kfree(p);
+ return err;
}
static int br_mdb_add_group(const struct br_mdb_config *cfg,
@@ -967,6 +1088,7 @@ static int br_mdb_config_init(struct net *net, const struct
nlmsghdr *nlh,
return err;
memset(cfg, 0, sizeof(*cfg));
+ cfg->filter_mode = MCAST_EXCLUDE;
bpm = nlmsg_data(nlh);
if (!bpm->ifindex) {
diff --git a/net/bridge/br_private.h b/net/bridge/br_private.h
index e98bfe3c02e1..368f5f6fa42b 100644
--- a/net/bridge/br_private.h
+++ b/net/bridge/br_private.h
@@ -93,12 +93,19 @@ struct bridge_mcast_stats {
struct u64_stats_sync syncp;
};
+struct br_mdb_src_entry {
+ struct br_ip addr;
+};
+
struct br_mdb_config {
struct net_bridge *br;
struct net_bridge_port *p;
struct br_mdb_entry *entry;
struct br_ip group;
bool src_entry;
+ u8 filter_mode;
+ struct br_mdb_src_entry *src_entries;
+ int num_src_entries;
};
#endif
--
2.37.3
Ido Schimmel
2022-Dec-08 15:28 UTC
[Bridge] [PATCH net-next 10/14] bridge: mcast: Allow user space to add (*, G) with a source list and filter mode
Add new netlink attributes to the RTM_NEWMDB request that allow user
space to add (*, G) with a source list and filter mode.
The RTM_NEWMDB message can already dump such entries (created by the
kernel) so there is no need to add dump support. However, the message
contains a different set of attributes depending if it is a request or a
response. The naming and structure of the new attributes try to follow
the existing ones used in the response.
Request:
[ struct nlmsghdr ]
[ struct br_port_msg ]
[ MDBA_SET_ENTRY ]
struct br_mdb_entry
[ MDBA_SET_ENTRY_ATTRS ]
[ MDBE_ATTR_SOURCE ]
struct in_addr / struct in6_addr
[ MDBE_ATTR_SRC_LIST ] // new
[ MDBE_SRC_LIST_ENTRY ]
[ MDBE_SRCATTR_ADDRESS ]
struct in_addr / struct in6_addr
[ ...]
[ MDBE_ATTR_GROUP_MODE ] // new
u8
Response:
[ struct nlmsghdr ]
[ struct br_port_msg ]
[ MDBA_MDB ]
[ MDBA_MDB_ENTRY ]
[ MDBA_MDB_ENTRY_INFO ]
struct br_mdb_entry
[ MDBA_MDB_EATTR_TIMER ]
u32
[ MDBA_MDB_EATTR_SOURCE ]
struct in_addr / struct in6_addr
[ MDBA_MDB_EATTR_RTPROT ]
u8
[ MDBA_MDB_EATTR_SRC_LIST ]
[ MDBA_MDB_SRCLIST_ENTRY ]
[ MDBA_MDB_SRCATTR_ADDRESS ]
struct in_addr / struct in6_addr
[ MDBA_MDB_SRCATTR_TIMER ]
u8
[...]
[ MDBA_MDB_EATTR_GROUP_MODE ]
u8
Signed-off-by: Ido Schimmel <idosch at nvidia.com>
---
Notes:
v1:
* Use an array instead of list to store source entries.
* Drop br_mdb_config_attrs_fini().
include/uapi/linux/if_bridge.h | 20 +++++
net/bridge/br_mdb.c | 130 +++++++++++++++++++++++++++++++++
2 files changed, 150 insertions(+)
diff --git a/include/uapi/linux/if_bridge.h b/include/uapi/linux/if_bridge.h
index a86a7e7b811f..0d9fe73fc48c 100644
--- a/include/uapi/linux/if_bridge.h
+++ b/include/uapi/linux/if_bridge.h
@@ -723,10 +723,30 @@ enum {
enum {
MDBE_ATTR_UNSPEC,
MDBE_ATTR_SOURCE,
+ MDBE_ATTR_SRC_LIST,
+ MDBE_ATTR_GROUP_MODE,
__MDBE_ATTR_MAX,
};
#define MDBE_ATTR_MAX (__MDBE_ATTR_MAX - 1)
+/* per mdb entry source */
+enum {
+ MDBE_SRC_LIST_UNSPEC,
+ MDBE_SRC_LIST_ENTRY,
+ __MDBE_SRC_LIST_MAX,
+};
+#define MDBE_SRC_LIST_MAX (__MDBE_SRC_LIST_MAX - 1)
+
+/* per mdb entry per source attributes
+ * these are embedded in MDBE_SRC_LIST_ENTRY
+ */
+enum {
+ MDBE_SRCATTR_UNSPEC,
+ MDBE_SRCATTR_ADDRESS,
+ __MDBE_SRCATTR_MAX,
+};
+#define MDBE_SRCATTR_MAX (__MDBE_SRCATTR_MAX - 1)
+
/* Embedded inside LINK_XSTATS_TYPE_BRIDGE */
enum {
BRIDGE_XSTATS_UNSPEC,
diff --git a/net/bridge/br_mdb.c b/net/bridge/br_mdb.c
index e9a4b7e247e7..61d46b0a31b6 100644
--- a/net/bridge/br_mdb.c
+++ b/net/bridge/br_mdb.c
@@ -663,10 +663,25 @@ void br_rtr_notify(struct net_device *dev, struct
net_bridge_mcast_port *pmctx,
rtnl_set_sk_err(net, RTNLGRP_MDB, err);
}
+static const struct nla_policy
+br_mdbe_src_list_entry_pol[MDBE_SRCATTR_MAX + 1] = {
+ [MDBE_SRCATTR_ADDRESS] = NLA_POLICY_RANGE(NLA_BINARY,
+ sizeof(struct in_addr),
+ sizeof(struct in6_addr)),
+};
+
+static const struct nla_policy
+br_mdbe_src_list_pol[MDBE_SRC_LIST_MAX + 1] = {
+ [MDBE_SRC_LIST_ENTRY] = NLA_POLICY_NESTED(br_mdbe_src_list_entry_pol),
+};
+
static const struct nla_policy br_mdbe_attrs_pol[MDBE_ATTR_MAX + 1] = {
[MDBE_ATTR_SOURCE] = NLA_POLICY_RANGE(NLA_BINARY,
sizeof(struct in_addr),
sizeof(struct in6_addr)),
+ [MDBE_ATTR_GROUP_MODE] = NLA_POLICY_RANGE(NLA_U8, MCAST_EXCLUDE,
+ MCAST_INCLUDE),
+ [MDBE_ATTR_SRC_LIST] = NLA_POLICY_NESTED(br_mdbe_src_list_pol),
};
static bool is_valid_mdb_entry(struct br_mdb_entry *entry,
@@ -1051,6 +1066,76 @@ static int __br_mdb_add(const struct br_mdb_config *cfg,
return ret;
}
+static int br_mdb_config_src_entry_init(struct nlattr *src_entry,
+ struct br_mdb_src_entry *src,
+ __be16 proto,
+ struct netlink_ext_ack *extack)
+{
+ struct nlattr *tb[MDBE_SRCATTR_MAX + 1];
+ int err;
+
+ err = nla_parse_nested(tb, MDBE_SRCATTR_MAX, src_entry,
+ br_mdbe_src_list_entry_pol, extack);
+ if (err)
+ return err;
+
+ if (NL_REQ_ATTR_CHECK(extack, src_entry, tb, MDBE_SRCATTR_ADDRESS))
+ return -EINVAL;
+
+ if (!is_valid_mdb_source(tb[MDBE_SRCATTR_ADDRESS], proto, extack))
+ return -EINVAL;
+
+ src->addr.proto = proto;
+ nla_memcpy(&src->addr.src, tb[MDBE_SRCATTR_ADDRESS],
+ nla_len(tb[MDBE_SRCATTR_ADDRESS]));
+
+ return 0;
+}
+
+static int br_mdb_config_src_list_init(struct nlattr *src_list,
+ struct br_mdb_config *cfg,
+ struct netlink_ext_ack *extack)
+{
+ struct nlattr *src_entry;
+ int rem, err;
+ int i = 0;
+
+ nla_for_each_nested(src_entry, src_list, rem)
+ cfg->num_src_entries++;
+
+ if (cfg->num_src_entries >= PG_SRC_ENT_LIMIT) {
+ NL_SET_ERR_MSG_FMT_MOD(extack, "Exceeded maximum number of source
entries (%u)",
+ PG_SRC_ENT_LIMIT - 1);
+ return -EINVAL;
+ }
+
+ cfg->src_entries = kcalloc(cfg->num_src_entries,
+ sizeof(struct br_mdb_src_entry), GFP_KERNEL);
+ if (!cfg->src_entries)
+ return -ENOMEM;
+
+ nla_for_each_nested(src_entry, src_list, rem) {
+ err = br_mdb_config_src_entry_init(src_entry,
+ &cfg->src_entries[i],
+ cfg->entry->addr.proto,
+ extack);
+ if (err)
+ goto err_src_entry_init;
+ i++;
+ }
+
+ return 0;
+
+err_src_entry_init:
+ kfree(cfg->src_entries);
+ return err;
+}
+
+static void br_mdb_config_src_list_fini(struct br_mdb_config *cfg)
+{
+ kfree(cfg->src_entries);
+}
+
static int br_mdb_config_attrs_init(struct nlattr *set_attrs,
struct br_mdb_config *cfg,
struct netlink_ext_ack *extack)
@@ -1070,6 +1155,44 @@ static int br_mdb_config_attrs_init(struct nlattr
*set_attrs,
__mdb_entry_to_br_ip(cfg->entry, &cfg->group, mdb_attrs);
+ if (mdb_attrs[MDBE_ATTR_GROUP_MODE]) {
+ if (!cfg->p) {
+ NL_SET_ERR_MSG_MOD(extack, "Filter mode cannot be set for host
groups");
+ return -EINVAL;
+ }
+ if (!br_multicast_is_star_g(&cfg->group)) {
+ NL_SET_ERR_MSG_MOD(extack, "Filter mode can only be set for (*, G)
entries");
+ return -EINVAL;
+ }
+ cfg->filter_mode = nla_get_u8(mdb_attrs[MDBE_ATTR_GROUP_MODE]);
+ } else {
+ cfg->filter_mode = MCAST_EXCLUDE;
+ }
+
+ if (mdb_attrs[MDBE_ATTR_SRC_LIST]) {
+ if (!cfg->p) {
+ NL_SET_ERR_MSG_MOD(extack, "Source list cannot be set for host
groups");
+ return -EINVAL;
+ }
+ if (!br_multicast_is_star_g(&cfg->group)) {
+ NL_SET_ERR_MSG_MOD(extack, "Source list can only be set for (*, G)
entries");
+ return -EINVAL;
+ }
+ if (!mdb_attrs[MDBE_ATTR_GROUP_MODE]) {
+ NL_SET_ERR_MSG_MOD(extack, "Source list cannot be set without filter
mode");
+ return -EINVAL;
+ }
+ err = br_mdb_config_src_list_init(mdb_attrs[MDBE_ATTR_SRC_LIST],
+ cfg, extack);
+ if (err)
+ return err;
+ }
+
+ if (!cfg->num_src_entries && cfg->filter_mode == MCAST_INCLUDE)
{
+ NL_SET_ERR_MSG_MOD(extack, "Cannot add (*, G) INCLUDE with an empty
source list");
+ return -EINVAL;
+ }
+
return 0;
}
@@ -1162,6 +1285,11 @@ static int br_mdb_config_init(struct net *net, const
struct nlmsghdr *nlh,
return 0;
}
+static void br_mdb_config_fini(struct br_mdb_config *cfg)
+{
+ br_mdb_config_src_list_fini(cfg);
+}
+
static int br_mdb_add(struct sk_buff *skb, struct nlmsghdr *nlh,
struct netlink_ext_ack *extack)
{
@@ -1220,6 +1348,7 @@ static int br_mdb_add(struct sk_buff *skb, struct nlmsghdr
*nlh,
}
out:
+ br_mdb_config_fini(&cfg);
return err;
}
@@ -1295,6 +1424,7 @@ static int br_mdb_del(struct sk_buff *skb, struct nlmsghdr
*nlh,
err = __br_mdb_del(&cfg);
}
+ br_mdb_config_fini(&cfg);
return err;
}
--
2.37.3
Ido Schimmel
2022-Dec-08 15:28 UTC
[Bridge] [PATCH net-next 11/14] bridge: mcast: Allow user space to specify MDB entry routing protocol
Add the 'MDBE_ATTR_RTPORT' attribute to allow user space to specify the
routing protocol of the MDB port group entry. Enforce a minimum value of
'RTPROT_STATIC' to prevent user space from using protocol values that
should only be set by the kernel (e.g., 'RTPROT_KERNEL'). Maintain
backward compatibility by defaulting to 'RTPROT_STATIC'.
The protocol is already visible to user space in RTM_NEWMDB responses
and notifications via the 'MDBA_MDB_EATTR_RTPROT' attribute.
The routing protocol allows a routing daemon to distinguish between
entries configured by it and those configured by the administrator. Once
MDB flush is supported, the protocol can be used as a criterion
according to which the flush is performed.
Examples:
# bridge mdb add dev br0 port dummy10 grp 239.1.1.1 permanent proto kernel
Error: integer out of range.
# bridge mdb add dev br0 port dummy10 grp 239.1.1.1 permanent proto static
# bridge mdb add dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent
proto zebra
# bridge mdb add dev br0 port dummy10 grp 239.1.1.2 permanent source_list
198.51.100.1,198.51.100.2 filter_mode include proto 250
# bridge -d mdb show
dev br0 port dummy10 grp 239.1.1.2 src 198.51.100.2 permanent filter_mode
include proto 250
dev br0 port dummy10 grp 239.1.1.2 src 198.51.100.1 permanent filter_mode
include proto 250
dev br0 port dummy10 grp 239.1.1.2 permanent filter_mode include source_list
198.51.100.2/0.00,198.51.100.1/0.00 proto 250
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent filter_mode include
proto zebra
dev br0 port dummy10 grp 239.1.1.1 permanent filter_mode exclude proto static
Signed-off-by: Ido Schimmel <idosch at nvidia.com>
---
Notes:
v1:
* Reject protocol for host entries.
include/uapi/linux/if_bridge.h | 1 +
net/bridge/br_mdb.c | 15 +++++++++++++--
net/bridge/br_private.h | 1 +
3 files changed, 15 insertions(+), 2 deletions(-)
diff --git a/include/uapi/linux/if_bridge.h b/include/uapi/linux/if_bridge.h
index 0d9fe73fc48c..d9de241d90f9 100644
--- a/include/uapi/linux/if_bridge.h
+++ b/include/uapi/linux/if_bridge.h
@@ -725,6 +725,7 @@ enum {
MDBE_ATTR_SOURCE,
MDBE_ATTR_SRC_LIST,
MDBE_ATTR_GROUP_MODE,
+ MDBE_ATTR_RTPROT,
__MDBE_ATTR_MAX,
};
#define MDBE_ATTR_MAX (__MDBE_ATTR_MAX - 1)
diff --git a/net/bridge/br_mdb.c b/net/bridge/br_mdb.c
index 61d46b0a31b6..72d4e53193e5 100644
--- a/net/bridge/br_mdb.c
+++ b/net/bridge/br_mdb.c
@@ -682,6 +682,7 @@ static const struct nla_policy
br_mdbe_attrs_pol[MDBE_ATTR_MAX + 1] = {
[MDBE_ATTR_GROUP_MODE] = NLA_POLICY_RANGE(NLA_U8, MCAST_EXCLUDE,
MCAST_INCLUDE),
[MDBE_ATTR_SRC_LIST] = NLA_POLICY_NESTED(br_mdbe_src_list_pol),
+ [MDBE_ATTR_RTPROT] = NLA_POLICY_MIN(NLA_U8, RTPROT_STATIC),
};
static bool is_valid_mdb_entry(struct br_mdb_entry *entry,
@@ -823,7 +824,7 @@ static int br_mdb_add_group_sg(const struct br_mdb_config
*cfg,
}
p = br_multicast_new_port_group(cfg->p, &cfg->group, *pp, flags,
NULL,
- MCAST_INCLUDE, RTPROT_STATIC);
+ MCAST_INCLUDE, cfg->rt_protocol);
if (unlikely(!p)) {
NL_SET_ERR_MSG_MOD(extack, "Couldn't allocate new (S, G) port
group");
return -ENOMEM;
@@ -881,6 +882,7 @@ static int br_mdb_add_group_src_fwd(const struct
br_mdb_config *cfg,
sg_cfg.group = sg_ip;
sg_cfg.src_entry = true;
sg_cfg.filter_mode = MCAST_INCLUDE;
+ sg_cfg.rt_protocol = cfg->rt_protocol;
return br_mdb_add_group_sg(&sg_cfg, sgmp, brmctx, flags, extack);
}
@@ -982,7 +984,7 @@ static int br_mdb_add_group_star_g(const struct
br_mdb_config *cfg,
}
p = br_multicast_new_port_group(cfg->p, &cfg->group, *pp, flags,
NULL,
- cfg->filter_mode, RTPROT_STATIC);
+ cfg->filter_mode, cfg->rt_protocol);
if (unlikely(!p)) {
NL_SET_ERR_MSG_MOD(extack, "Couldn't allocate new (*, G) port
group");
return -ENOMEM;
@@ -1193,6 +1195,14 @@ static int br_mdb_config_attrs_init(struct nlattr
*set_attrs,
return -EINVAL;
}
+ if (mdb_attrs[MDBE_ATTR_RTPROT]) {
+ if (!cfg->p) {
+ NL_SET_ERR_MSG_MOD(extack, "Protocol cannot be set for host
groups");
+ return -EINVAL;
+ }
+ cfg->rt_protocol = nla_get_u8(mdb_attrs[MDBE_ATTR_RTPROT]);
+ }
+
return 0;
}
@@ -1212,6 +1222,7 @@ static int br_mdb_config_init(struct net *net, const
struct nlmsghdr *nlh,
memset(cfg, 0, sizeof(*cfg));
cfg->filter_mode = MCAST_EXCLUDE;
+ cfg->rt_protocol = RTPROT_STATIC;
bpm = nlmsg_data(nlh);
if (!bpm->ifindex) {
diff --git a/net/bridge/br_private.h b/net/bridge/br_private.h
index 368f5f6fa42b..cdc9e040f1f6 100644
--- a/net/bridge/br_private.h
+++ b/net/bridge/br_private.h
@@ -106,6 +106,7 @@ struct br_mdb_config {
u8 filter_mode;
struct br_mdb_src_entry *src_entries;
int num_src_entries;
+ u8 rt_protocol;
};
#endif
--
2.37.3
Ido Schimmel
2022-Dec-08 15:28 UTC
[Bridge] [PATCH net-next 12/14] bridge: mcast: Support replacement of MDB port group entries
Now that user space can specify additional attributes of port group
entries such as filter mode and source list, it makes sense to allow
user space to atomically modify these attributes by replacing entries
instead of forcing user space to delete the entries and add them back.
Replace MDB port group entries when the 'NLM_F_REPLACE' flag is
specified in the netlink message header.
When a (*, G) entry is replaced, update the following attributes: Source
list, state, filter mode, protocol and flags. If the entry is temporary
and in EXCLUDE mode, reset the group timer to the group membership
interval. If the entry is temporary and in INCLUDE mode, reset the
source timers of associated sources to the group membership interval.
Examples:
# bridge mdb replace dev br0 port dummy10 grp 239.1.1.1 permanent source_list
192.0.2.1,192.0.2.2 filter_mode include
# bridge -d -s mdb show
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.2 permanent filter_mode include
proto static 0.00
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent filter_mode include
proto static 0.00
dev br0 port dummy10 grp 239.1.1.1 permanent filter_mode include source_list
192.0.2.2/0.00,192.0.2.1/0.00 proto static 0.00
# bridge mdb replace dev br0 port dummy10 grp 239.1.1.1 permanent source_list
192.0.2.1,192.0.2.3 filter_mode exclude proto zebra
# bridge -d -s mdb show
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.3 permanent filter_mode include
proto zebra blocked 0.00
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent filter_mode include
proto zebra blocked 0.00
dev br0 port dummy10 grp 239.1.1.1 permanent filter_mode exclude source_list
192.0.2.3/0.00,192.0.2.1/0.00 proto zebra 0.00
# bridge mdb replace dev br0 port dummy10 grp 239.1.1.1 temp source_list
192.0.2.4,192.0.2.3 filter_mode include proto bgp
# bridge -d -s mdb show
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.4 temp filter_mode include proto
bgp 0.00
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.3 temp filter_mode include proto
bgp 0.00
dev br0 port dummy10 grp 239.1.1.1 temp filter_mode include source_list
192.0.2.4/259.44,192.0.2.3/259.44 proto bgp 0.00
Signed-off-by: Ido Schimmel <idosch at nvidia.com>
---
net/bridge/br_mdb.c | 103 ++++++++++++++++++++++++++++++++++++++--
net/bridge/br_private.h | 1 +
2 files changed, 99 insertions(+), 5 deletions(-)
diff --git a/net/bridge/br_mdb.c b/net/bridge/br_mdb.c
index 72d4e53193e5..98d899427c03 100644
--- a/net/bridge/br_mdb.c
+++ b/net/bridge/br_mdb.c
@@ -802,6 +802,28 @@ __br_mdb_choose_context(struct net_bridge *br,
return brmctx;
}
+static int br_mdb_replace_group_sg(const struct br_mdb_config *cfg,
+ struct net_bridge_mdb_entry *mp,
+ struct net_bridge_port_group *pg,
+ struct net_bridge_mcast *brmctx,
+ unsigned char flags,
+ struct netlink_ext_ack *extack)
+{
+ unsigned long now = jiffies;
+
+ pg->flags = flags;
+ pg->rt_protocol = cfg->rt_protocol;
+ if (!(flags & MDB_PG_FLAGS_PERMANENT) && !cfg->src_entry)
+ mod_timer(&pg->timer,
+ now + brmctx->multicast_membership_interval);
+ else
+ del_timer(&pg->timer);
+
+ br_mdb_notify(cfg->br->dev, mp, pg, RTM_NEWMDB);
+
+ return 0;
+}
+
static int br_mdb_add_group_sg(const struct br_mdb_config *cfg,
struct net_bridge_mdb_entry *mp,
struct net_bridge_mcast *brmctx,
@@ -816,8 +838,12 @@ static int br_mdb_add_group_sg(const struct br_mdb_config
*cfg,
(p = mlock_dereference(*pp, cfg->br)) != NULL;
pp = &p->next) {
if (p->key.port == cfg->p) {
- NL_SET_ERR_MSG_MOD(extack, "(S, G) group is already joined by
port");
- return -EEXIST;
+ if (!(cfg->nlflags & NLM_F_REPLACE)) {
+ NL_SET_ERR_MSG_MOD(extack, "(S, G) group is already joined by
port");
+ return -EEXIST;
+ }
+ return br_mdb_replace_group_sg(cfg, mp, p, brmctx,
+ flags, extack);
}
if ((unsigned long)p->key.port < (unsigned long)cfg->p)
break;
@@ -883,6 +909,7 @@ static int br_mdb_add_group_src_fwd(const struct
br_mdb_config *cfg,
sg_cfg.src_entry = true;
sg_cfg.filter_mode = MCAST_INCLUDE;
sg_cfg.rt_protocol = cfg->rt_protocol;
+ sg_cfg.nlflags = cfg->nlflags;
return br_mdb_add_group_sg(&sg_cfg, sgmp, brmctx, flags, extack);
}
@@ -903,7 +930,7 @@ static int br_mdb_add_group_src(const struct br_mdb_config
*cfg,
NL_SET_ERR_MSG_MOD(extack, "Failed to add new source entry");
return -ENOSPC;
}
- } else {
+ } else if (!(cfg->nlflags & NLM_F_REPLACE)) {
NL_SET_ERR_MSG_MOD(extack, "Source entry already exists");
return -EEXIST;
}
@@ -961,6 +988,67 @@ static int br_mdb_add_group_srcs(const struct br_mdb_config
*cfg,
return err;
}
+static int br_mdb_replace_group_srcs(const struct br_mdb_config *cfg,
+ struct net_bridge_port_group *pg,
+ struct net_bridge_mcast *brmctx,
+ struct netlink_ext_ack *extack)
+{
+ struct net_bridge_group_src *ent;
+ struct hlist_node *tmp;
+ int err;
+
+ hlist_for_each_entry(ent, &pg->src_list, node)
+ ent->flags |= BR_SGRP_F_DELETE;
+
+ err = br_mdb_add_group_srcs(cfg, pg, brmctx, extack);
+ if (err)
+ goto err_clear_delete;
+
+ hlist_for_each_entry_safe(ent, tmp, &pg->src_list, node) {
+ if (ent->flags & BR_SGRP_F_DELETE)
+ br_multicast_del_group_src(ent, false);
+ }
+
+ return 0;
+
+err_clear_delete:
+ hlist_for_each_entry(ent, &pg->src_list, node)
+ ent->flags &= ~BR_SGRP_F_DELETE;
+ return err;
+}
+
+static int br_mdb_replace_group_star_g(const struct br_mdb_config *cfg,
+ struct net_bridge_mdb_entry *mp,
+ struct net_bridge_port_group *pg,
+ struct net_bridge_mcast *brmctx,
+ unsigned char flags,
+ struct netlink_ext_ack *extack)
+{
+ unsigned long now = jiffies;
+ int err;
+
+ err = br_mdb_replace_group_srcs(cfg, pg, brmctx, extack);
+ if (err)
+ return err;
+
+ pg->flags = flags;
+ pg->filter_mode = cfg->filter_mode;
+ pg->rt_protocol = cfg->rt_protocol;
+ if (!(flags & MDB_PG_FLAGS_PERMANENT) &&
+ cfg->filter_mode == MCAST_EXCLUDE)
+ mod_timer(&pg->timer,
+ now + brmctx->multicast_membership_interval);
+ else
+ del_timer(&pg->timer);
+
+ br_mdb_notify(cfg->br->dev, mp, pg, RTM_NEWMDB);
+
+ if (br_multicast_should_handle_mode(brmctx, cfg->group.proto))
+ br_multicast_star_g_handle_mode(pg, cfg->filter_mode);
+
+ return 0;
+}
+
static int br_mdb_add_group_star_g(const struct br_mdb_config *cfg,
struct net_bridge_mdb_entry *mp,
struct net_bridge_mcast *brmctx,
@@ -976,8 +1064,12 @@ static int br_mdb_add_group_star_g(const struct
br_mdb_config *cfg,
(p = mlock_dereference(*pp, cfg->br)) != NULL;
pp = &p->next) {
if (p->key.port == cfg->p) {
- NL_SET_ERR_MSG_MOD(extack, "(*, G) group is already joined by
port");
- return -EEXIST;
+ if (!(cfg->nlflags & NLM_F_REPLACE)) {
+ NL_SET_ERR_MSG_MOD(extack, "(*, G) group is already joined by
port");
+ return -EEXIST;
+ }
+ return br_mdb_replace_group_star_g(cfg, mp, p, brmctx,
+ flags, extack);
}
if ((unsigned long)p->key.port < (unsigned long)cfg->p)
break;
@@ -1223,6 +1315,7 @@ static int br_mdb_config_init(struct net *net, const
struct nlmsghdr *nlh,
memset(cfg, 0, sizeof(*cfg));
cfg->filter_mode = MCAST_EXCLUDE;
cfg->rt_protocol = RTPROT_STATIC;
+ cfg->nlflags = nlh->nlmsg_flags;
bpm = nlmsg_data(nlh);
if (!bpm->ifindex) {
diff --git a/net/bridge/br_private.h b/net/bridge/br_private.h
index cdc9e040f1f6..2473add41e16 100644
--- a/net/bridge/br_private.h
+++ b/net/bridge/br_private.h
@@ -107,6 +107,7 @@ struct br_mdb_config {
struct br_mdb_src_entry *src_entries;
int num_src_entries;
u8 rt_protocol;
+ u32 nlflags;
};
#endif
--
2.37.3
Ido Schimmel
2022-Dec-08 15:28 UTC
[Bridge] [PATCH net-next 13/14] selftests: forwarding: Rename bridge_mdb test
The test is only concerned with host MDB entries and not with MDB
entries as a whole. Rename the test to reflect that.
Subsequent patches will add a more general test that will contain the
test cases for host MDB entries and remove the current test.
Signed-off-by: Ido Schimmel <idosch at nvidia.com>
---
tools/testing/selftests/net/forwarding/Makefile | 2 +-
.../net/forwarding/{bridge_mdb.sh => bridge_mdb_host.sh} | 0
2 files changed, 1 insertion(+), 1 deletion(-)
rename tools/testing/selftests/net/forwarding/{bridge_mdb.sh =>
bridge_mdb_host.sh} (100%)
diff --git a/tools/testing/selftests/net/forwarding/Makefile
b/tools/testing/selftests/net/forwarding/Makefile
index a9c5c1be5088..f2df81ca3179 100644
--- a/tools/testing/selftests/net/forwarding/Makefile
+++ b/tools/testing/selftests/net/forwarding/Makefile
@@ -2,7 +2,7 @@
TEST_PROGS = bridge_igmp.sh \
bridge_locked_port.sh \
- bridge_mdb.sh \
+ bridge_mdb_host.sh \
bridge_mdb_port_down.sh \
bridge_mld.sh \
bridge_port_isolation.sh \
diff --git a/tools/testing/selftests/net/forwarding/bridge_mdb.sh
b/tools/testing/selftests/net/forwarding/bridge_mdb_host.sh
similarity index 100%
rename from tools/testing/selftests/net/forwarding/bridge_mdb.sh
rename to tools/testing/selftests/net/forwarding/bridge_mdb_host.sh
--
2.37.3
Ido Schimmel
2022-Dec-08 15:28 UTC
[Bridge] [PATCH net-next 14/14] selftests: forwarding: Add bridge MDB test
Add a selftests that includes the following test cases:
1. Configuration tests. Both valid and invalid configurations are
tested across all entry types (e.g., L2, IPv4).
2. Forwarding tests. Both host and port group entries are tested across
all entry types.
3. Interaction between user installed MDB entries and IGMP / MLD control
packets.
Example output:
INFO: # Host entries configuration tests
TEST: Common host entries configuration tests (IPv4) [ OK ]
TEST: Common host entries configuration tests (IPv6) [ OK ]
TEST: Common host entries configuration tests (L2) [ OK ]
INFO: # Port group entries configuration tests - (*, G)
TEST: Common port group entries configuration tests (IPv4 (*, G)) [ OK ]
TEST: Common port group entries configuration tests (IPv6 (*, G)) [ OK ]
TEST: IPv4 (*, G) port group entries configuration tests [ OK ]
TEST: IPv6 (*, G) port group entries configuration tests [ OK ]
INFO: # Port group entries configuration tests - (S, G)
TEST: Common port group entries configuration tests (IPv4 (S, G)) [ OK ]
TEST: Common port group entries configuration tests (IPv6 (S, G)) [ OK ]
TEST: IPv4 (S, G) port group entries configuration tests [ OK ]
TEST: IPv6 (S, G) port group entries configuration tests [ OK ]
INFO: # Port group entries configuration tests - L2
TEST: Common port group entries configuration tests (L2 (*, G)) [ OK ]
TEST: L2 (*, G) port group entries configuration tests [ OK ]
INFO: # Forwarding tests
TEST: IPv4 host entries forwarding tests [ OK ]
TEST: IPv6 host entries forwarding tests [ OK ]
TEST: L2 host entries forwarding tests [ OK ]
TEST: IPv4 port group "exclude" entries forwarding tests [
OK ]
TEST: IPv6 port group "exclude" entries forwarding tests [
OK ]
TEST: IPv4 port group "include" entries forwarding tests [
OK ]
TEST: IPv6 port group "include" entries forwarding tests [
OK ]
TEST: L2 port entries forwarding tests [ OK ]
INFO: # Control packets tests
TEST: IGMPv3 MODE_IS_INCLUE tests [ OK ]
TEST: MLDv2 MODE_IS_INCLUDE tests [ OK ]
Signed-off-by: Ido Schimmel <idosch at nvidia.com>
---
.../testing/selftests/net/forwarding/Makefile | 1 +
.../selftests/net/forwarding/bridge_mdb.sh | 1164 +++++++++++++++++
2 files changed, 1165 insertions(+)
create mode 100755 tools/testing/selftests/net/forwarding/bridge_mdb.sh
diff --git a/tools/testing/selftests/net/forwarding/Makefile
b/tools/testing/selftests/net/forwarding/Makefile
index f2df81ca3179..453ae006fbcf 100644
--- a/tools/testing/selftests/net/forwarding/Makefile
+++ b/tools/testing/selftests/net/forwarding/Makefile
@@ -2,6 +2,7 @@
TEST_PROGS = bridge_igmp.sh \
bridge_locked_port.sh \
+ bridge_mdb.sh \
bridge_mdb_host.sh \
bridge_mdb_port_down.sh \
bridge_mld.sh \
diff --git a/tools/testing/selftests/net/forwarding/bridge_mdb.sh
b/tools/testing/selftests/net/forwarding/bridge_mdb.sh
new file mode 100755
index 000000000000..2fa5973c0c28
--- /dev/null
+++ b/tools/testing/selftests/net/forwarding/bridge_mdb.sh
@@ -0,0 +1,1164 @@
+#!/bin/bash
+# SPDX-License-Identifier: GPL-2.0
+
+# +-----------------------+ +------------------------+
+# | H1 (vrf) | | H2 (vrf) |
+# | + $h1.10 | | + $h2.10 |
+# | | 192.0.2.1/28 | | | 192.0.2.2/28 |
+# | | 2001:db8:1::1/64 | | | 2001:db8:1::2/64 |
+# | | | | | |
+# | | + $h1.20 | | | + $h2.20 |
+# | \ | 198.51.100.1/24 | | \ | 198.51.100.2/24 |
+# | \ | 2001:db8:2::1/64 | | \ | 2001:db8:2::2/64 |
+# | \| | | \| |
+# | + $h1 | | + $h2 |
+# +----|------------------+ +----|-------------------+
+# | |
+# +----|--------------------------------------------------|-------------------+
+# | SW | | |
+# | +--|--------------------------------------------------|-----------------+ |
+# | | + $swp1 BR0 (802.1q) + $swp2 | |
+# | | vid 10 vid 10 | |
+# | | vid 20 vid 20 | |
+# | | | |
+# | +-----------------------------------------------------------------------+ |
+# +---------------------------------------------------------------------------+
+
+ALL_TESTS="
+ cfg_test
+ fwd_test
+ ctrl_test
+"
+
+NUM_NETIFS=4
+source lib.sh
+source tc_common.sh
+
+h1_create()
+{
+ simple_if_init $h1
+ vlan_create $h1 10 v$h1 192.0.2.1/28 2001:db8:1::1/64
+ vlan_create $h1 20 v$h1 198.51.100.1/24 2001:db8:2::1/64
+}
+
+h1_destroy()
+{
+ vlan_destroy $h1 20
+ vlan_destroy $h1 10
+ simple_if_fini $h1
+}
+
+h2_create()
+{
+ simple_if_init $h2
+ vlan_create $h2 10 v$h2 192.0.2.2/28
+ vlan_create $h2 20 v$h2 198.51.100.2/24
+}
+
+h2_destroy()
+{
+ vlan_destroy $h2 20
+ vlan_destroy $h2 10
+ simple_if_fini $h2
+}
+
+switch_create()
+{
+ ip link add name br0 type bridge vlan_filtering 1 vlan_default_pvid 0 \
+ mcast_snooping 1 mcast_igmp_version 3 mcast_mld_version 2
+ bridge vlan add vid 10 dev br0 self
+ bridge vlan add vid 20 dev br0 self
+ ip link set dev br0 up
+
+ ip link set dev $swp1 master br0
+ ip link set dev $swp1 up
+ bridge vlan add vid 10 dev $swp1
+ bridge vlan add vid 20 dev $swp1
+
+ ip link set dev $swp2 master br0
+ ip link set dev $swp2 up
+ bridge vlan add vid 10 dev $swp2
+ bridge vlan add vid 20 dev $swp2
+
+ tc qdisc add dev br0 clsact
+ tc qdisc add dev $h2 clsact
+}
+
+switch_destroy()
+{
+ tc qdisc del dev $h2 clsact
+ tc qdisc del dev br0 clsact
+
+ bridge vlan del vid 20 dev $swp2
+ bridge vlan del vid 10 dev $swp2
+ ip link set dev $swp2 down
+ ip link set dev $swp2 nomaster
+
+ bridge vlan del vid 20 dev $swp1
+ bridge vlan del vid 10 dev $swp1
+ ip link set dev $swp1 down
+ ip link set dev $swp1 nomaster
+
+ ip link set dev br0 down
+ bridge vlan del vid 20 dev br0 self
+ bridge vlan del vid 10 dev br0 self
+ ip link del dev br0
+}
+
+setup_prepare()
+{
+ h1=${NETIFS[p1]}
+ swp1=${NETIFS[p2]}
+
+ swp2=${NETIFS[p3]}
+ h2=${NETIFS[p4]}
+
+ vrf_prepare
+ forwarding_enable
+
+ h1_create
+ h2_create
+ switch_create
+}
+
+cleanup()
+{
+ pre_cleanup
+
+ switch_destroy
+ h2_destroy
+ h1_destroy
+
+ forwarding_restore
+ vrf_cleanup
+}
+
+cfg_test_host_common()
+{
+ local name=$1; shift
+ local grp=$1; shift
+ local src=$1; shift
+ local state=$1; shift
+ local invalid_state=$1; shift
+
+ RET=0
+
+ # Check basic add, replace and delete behavior.
+ bridge mdb add dev br0 port br0 grp $grp $state vid 10
+ bridge mdb show dev br0 vid 10 | grep -q "$grp"
+ check_err $? "Failed to add $name host entry"
+
+ bridge mdb replace dev br0 port br0 grp $grp $state vid 10 &> /dev/null
+ check_fail $? "Managed to replace $name host entry"
+
+ bridge mdb del dev br0 port br0 grp $grp $state vid 10
+ bridge mdb show dev br0 vid 10 | grep -q "$grp"
+ check_fail $? "Failed to delete $name host entry"
+
+ # Check error cases.
+ bridge mdb add dev br0 port br0 grp $grp $invalid_state vid 10 \
+ &> /dev/null
+ check_fail $? "Managed to add $name host entry with a $invalid_state
state"
+
+ bridge mdb add dev br0 port br0 grp $grp src $src $state vid 10 \
+ &> /dev/null
+ check_fail $? "Managed to add $name host entry with a source"
+
+ bridge mdb add dev br0 port br0 grp $grp $state vid 10 \
+ filter_mode exclude &> /dev/null
+ check_fail $? "Managed to add $name host entry with a filter mode"
+
+ bridge mdb add dev br0 port br0 grp $grp $state vid 10 \
+ source_list $src &> /dev/null
+ check_fail $? "Managed to add $name host entry with a source list"
+
+ bridge mdb add dev br0 port br0 grp $grp $state vid 10 \
+ proto 123 &> /dev/null
+ check_fail $? "Managed to add $name host entry with a protocol"
+
+ log_test "Common host entries configuration tests ($name)"
+}
+
+# Check configuration of host entries from all types.
+cfg_test_host()
+{
+ echo
+ log_info "# Host entries configuration tests"
+
+ cfg_test_host_common "IPv4" "239.1.1.1"
"192.0.2.1" "temp" "permanent"
+ cfg_test_host_common "IPv6" "ff0e::1"
"2001:db8:1::1" "temp" "permanent"
+ cfg_test_host_common "L2" "01:02:03:04:05:06"
"00:00:00:00:00:01" \
+ "permanent" "temp"
+}
+
+cfg_test_port_common()
+{
+ local name=$1;shift
+ local grp_key=$1; shift
+
+ RET=0
+
+ # Check basic add, replace and delete behavior.
+ bridge mdb add dev br0 port $swp1 $grp_key permanent vid 10
+ bridge mdb show dev br0 vid 10 | grep -q "$grp_key"
+ check_err $? "Failed to add $name entry"
+
+ bridge mdb replace dev br0 port $swp1 $grp_key permanent vid 10 \
+ &> /dev/null
+ check_err $? "Failed to replace $name entry"
+
+ bridge mdb del dev br0 port $swp1 $grp_key permanent vid 10
+ bridge mdb show dev br0 vid 10 | grep -q "$grp_key"
+ check_fail $? "Failed to delete $name entry"
+
+ # Check default protocol and replacement.
+ bridge mdb add dev br0 port $swp1 $grp_key permanent vid 10
+ bridge -d mdb show dev br0 vid 10 | grep "$grp_key" | grep -q
"static"
+ check_err $? "$name entry not added with default \"static\"
protocol"
+
+ bridge mdb replace dev br0 port $swp1 $grp_key permanent vid 10 \
+ proto 123
+ bridge -d mdb show dev br0 vid 10 | grep "$grp_key" | grep -q
"123"
+ check_err $? "Failed to replace protocol of $name entry"
+ bridge mdb del dev br0 port $swp1 $grp_key permanent vid 10
+
+ # Check behavior when VLAN is not specified.
+ bridge mdb add dev br0 port $swp1 $grp_key permanent
+ bridge mdb show dev br0 vid 10 | grep -q "$grp_key"
+ check_err $? "$name entry with VLAN 10 not added when VLAN was not
specified"
+ bridge mdb show dev br0 vid 20 | grep -q "$grp_key"
+ check_err $? "$name entry with VLAN 20 not added when VLAN was not
specified"
+
+ bridge mdb del dev br0 port $swp1 $grp_key permanent
+ bridge mdb show dev br0 vid 10 | grep -q "$grp_key"
+ check_fail $? "$name entry with VLAN 10 not deleted when VLAN was not
specified"
+ bridge mdb show dev br0 vid 20 | grep -q "$grp_key"
+ check_fail $? "$name entry with VLAN 20 not deleted when VLAN was not
specified"
+
+ # Check behavior when bridge port is down.
+ ip link set dev $swp1 down
+
+ bridge mdb add dev br0 port $swp1 $grp_key permanent vid 10
+ check_err $? "Failed to add $name permanent entry when bridge port is
down"
+
+ bridge mdb del dev br0 port $swp1 $grp_key permanent vid 10
+
+ bridge mdb add dev br0 port $swp1 $grp_key temp vid 10 &> /dev/null
+ check_fail $? "Managed to add $name temporary entry when bridge port is
down"
+
+ ip link set dev $swp1 up
+ setup_wait_dev $swp1
+
+ # Check error cases.
+ ip link set dev br0 down
+ bridge mdb add dev br0 port $swp1 $grp_key permanent vid 10 \
+ &> /dev/null
+ check_fail $? "Managed to add $name entry when bridge is down"
+ ip link set dev br0 up
+
+ ip link set dev br0 type bridge mcast_snooping 0
+ bridge mdb add dev br0 port $swp1 $grp_key permanent vid \
+ 10 &> /dev/null
+ check_fail $? "Managed to add $name entry when multicast snooping is
disabled"
+ ip link set dev br0 type bridge mcast_snooping 1
+
+ bridge mdb add dev br0 port $swp1 $grp_key permanent vid 5000 \
+ &> /dev/null
+ check_fail $? "Managed to add $name entry with an invalid VLAN"
+
+ log_test "Common port group entries configuration tests ($name)"
+}
+
+src_list_create()
+{
+ local src_prefix=$1; shift
+ local num_srcs=$1; shift
+ local src_list
+ local i
+
+ for i in $(seq 1 $num_srcs); do
+ src_list=${src_list},${src_prefix}${i}
+ done
+
+ echo $src_list | cut -c 2-
+}
+
+__cfg_test_port_ip_star_g()
+{
+ local name=$1; shift
+ local grp=$1; shift
+ local invalid_grp=$1; shift
+ local src_prefix=$1; shift
+ local src1=${src_prefix}1
+ local src2=${src_prefix}2
+ local src3=${src_prefix}3
+ local max_srcs=31
+ local num_srcs
+
+ RET=0
+
+ bridge mdb add dev br0 port $swp1 grp $grp vid 10
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -q
"exclude"
+ check_err $? "Default filter mode is not \"exclude\""
+ bridge mdb del dev br0 port $swp1 grp $grp vid 10
+
+ # Check basic add and delete behavior.
+ bridge mdb add dev br0 port $swp1 grp $grp vid 10 filter_mode exclude \
+ source_list $src1
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -q -v
"src"
+ check_err $? "(*, G) entry not created"
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -q "src
$src1"
+ check_err $? "(S, G) entry not created"
+ bridge mdb del dev br0 port $swp1 grp $grp vid 10
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -q -v
"src"
+ check_fail $? "(*, G) entry not deleted"
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -q "src
$src1"
+ check_fail $? "(S, G) entry not deleted"
+
+ ## State (permanent / temp) tests.
+
+ # Check that group and source timer are not set for permanent entries.
+ bridge mdb add dev br0 port $swp1 grp $grp permanent vid 10 \
+ filter_mode exclude source_list $src1
+
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -v
"src" | \
+ grep -q "permanent"
+ check_err $? "(*, G) entry not added as \"permanent\" when
should"
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep
"src" | \
+ grep -q "permanent"
+ check_err $? "(S, G) entry not added as \"permanent\" when
should"
+
+ bridge -d -s mdb show dev br0 vid 10 | grep "$grp" | grep -v
"src" | \
+ grep -q " 0.00"
+ check_err $? "(*, G) \"permanent\" entry has a pending group
timer"
+ bridge -d -s mdb show dev br0 vid 10 | grep "$grp" | grep -v
"src" | \
+ grep -q "\/0.00"
+ check_err $? "\"permanent\" source entry has a pending source
timer"
+
+ bridge mdb del dev br0 port $swp1 grp $grp vid 10
+
+ # Check that group timer is set for temporary (*, G) EXCLUDE, but not
+ # the source timer.
+ bridge mdb add dev br0 port $swp1 grp $grp temp vid 10 \
+ filter_mode exclude source_list $src1
+
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -v
"src" | \
+ grep -q "temp"
+ check_err $? "(*, G) EXCLUDE entry not added as \"temp\" when
should"
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep
"src" | \
+ grep -q "temp"
+ check_err $? "(S, G) \"blocked\" entry not added as
\"temp\" when should"
+
+ bridge -d -s mdb show dev br0 vid 10 | grep "$grp" | grep -v
"src" | \
+ grep -q " 0.00"
+ check_fail $? "(*, G) EXCLUDE entry does not have a pending group
timer"
+ bridge -d -s mdb show dev br0 vid 10 | grep "$grp" | grep -v
"src" | \
+ grep -q "\/0.00"
+ check_err $? "\"blocked\" source entry has a pending source
timer"
+
+ bridge mdb del dev br0 port $swp1 grp $grp vid 10
+
+ # Check that group timer is not set for temporary (*, G) INCLUDE, but
+ # that the source timer is set.
+ bridge mdb add dev br0 port $swp1 grp $grp temp vid 10 \
+ filter_mode include source_list $src1
+
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -v
"src" | \
+ grep -q "temp"
+ check_err $? "(*, G) INCLUDE entry not added as \"temp\" when
should"
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep
"src" | \
+ grep -q "temp"
+ check_err $? "(S, G) entry not added as \"temp\" when
should"
+
+ bridge -d -s mdb show dev br0 vid 10 | grep "$grp" | grep -v
"src" | \
+ grep -q " 0.00"
+ check_err $? "(*, G) INCLUDE entry has a pending group timer"
+ bridge -d -s mdb show dev br0 vid 10 | grep "$grp" | grep -v
"src" | \
+ grep -q "\/0.00"
+ check_fail $? "Source entry does not have a pending source timer"
+
+ bridge mdb del dev br0 port $swp1 grp $grp vid 10
+
+ # Check that group timer is never set for (S, G) entries.
+ bridge mdb add dev br0 port $swp1 grp $grp temp vid 10 \
+ filter_mode include source_list $src1
+
+ bridge -d -s mdb show dev br0 vid 10 | grep "$grp" | grep
"src" | \
+ grep -q " 0.00"
+ check_err $? "(S, G) entry has a pending group timer"
+
+ bridge mdb del dev br0 port $swp1 grp $grp vid 10
+
+ ## Filter mode (include / exclude) tests.
+
+ # Check that (*, G) INCLUDE entries are added with correct filter mode
+ # and that (S, G) entries are not marked as "blocked".
+ bridge mdb add dev br0 port $swp1 grp $grp vid 10 \
+ filter_mode include source_list $src1
+
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -v
"src" | \
+ grep -q "include"
+ check_err $? "(*, G) INCLUDE not added with \"include\" filter
mode"
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep
"src" | \
+ grep -q "blocked"
+ check_fail $? "(S, G) entry marked as \"blocked\" when should
not"
+
+ bridge mdb del dev br0 port $swp1 grp $grp vid 10
+
+ # Check that (*, G) EXCLUDE entries are added with correct filter mode
+ # and that (S, G) entries are marked as "blocked".
+ bridge mdb add dev br0 port $swp1 grp $grp vid 10 \
+ filter_mode exclude source_list $src1
+
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -v
"src" | \
+ grep -q "exclude"
+ check_err $? "(*, G) EXCLUDE not added with \"exclude\" filter
mode"
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep
"src" | \
+ grep -q "blocked"
+ check_err $? "(S, G) entry not marked as \"blocked\" when
should"
+
+ bridge mdb del dev br0 port $swp1 grp $grp vid 10
+
+ ## Protocol tests.
+
+ # Check that (*, G) and (S, G) entries are added with the specified
+ # protocol.
+ bridge mdb add dev br0 port $swp1 grp $grp vid 10 \
+ filter_mode exclude source_list $src1 proto zebra
+
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -v
"src" | \
+ grep -q "zebra"
+ check_err $? "(*, G) entry not added with \"zebra\"
protocol"
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep
"src" | \
+ grep -q "zebra"
+ check_err $? "(S, G) entry not marked added with \"zebra\"
protocol"
+
+ bridge mdb del dev br0 port $swp1 grp $grp vid 10
+
+ ## Replace tests.
+
+ # Check that state can be modified.
+ bridge mdb add dev br0 port $swp1 grp $grp temp vid 10 \
+ filter_mode exclude source_list $src1
+
+ bridge mdb replace dev br0 port $swp1 grp $grp permanent vid 10 \
+ filter_mode exclude source_list $src1
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -v
"src" | \
+ grep -q "permanent"
+ check_err $? "(*, G) entry not marked as \"permanent\" after
replace"
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep
"src" | \
+ grep -q "permanent"
+ check_err $? "(S, G) entry not marked as \"permanent\" after
replace"
+
+ bridge mdb replace dev br0 port $swp1 grp $grp temp vid 10 \
+ filter_mode exclude source_list $src1
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -v
"src" | \
+ grep -q "temp"
+ check_err $? "(*, G) entry not marked as \"temp\" after
replace"
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep
"src" | \
+ grep -q "temp"
+ check_err $? "(S, G) entry not marked as \"temp\" after
replace"
+
+ bridge mdb del dev br0 port $swp1 grp $grp vid 10
+
+ # Check that filter mode can be modified.
+ bridge mdb add dev br0 port $swp1 grp $grp temp vid 10 \
+ filter_mode exclude source_list $src1
+
+ bridge mdb replace dev br0 port $swp1 grp $grp temp vid 10 \
+ filter_mode include source_list $src1
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -v
"src" | \
+ grep -q "include"
+ check_err $? "(*, G) not marked with \"include\" filter mode
after replace"
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep
"src" | \
+ grep -q "blocked"
+ check_fail $? "(S, G) marked as \"blocked\" after replace"
+
+ bridge mdb replace dev br0 port $swp1 grp $grp temp vid 10 \
+ filter_mode exclude source_list $src1
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -v
"src" | \
+ grep -q "exclude"
+ check_err $? "(*, G) not marked with \"exclude\" filter mode
after replace"
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep
"src" | \
+ grep -q "blocked"
+ check_err $? "(S, G) not marked as \"blocked\" after
replace"
+
+ bridge mdb del dev br0 port $swp1 grp $grp vid 10
+
+ # Check that sources can be added to and removed from the source list.
+ bridge mdb add dev br0 port $swp1 grp $grp temp vid 10 \
+ filter_mode exclude source_list $src1
+
+ bridge mdb replace dev br0 port $swp1 grp $grp temp vid 10 \
+ filter_mode exclude source_list $src1,$src2,$src3
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -q "src
$src1"
+ check_err $? "(S, G) entry for source $src1 not created after
replace"
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -q "src
$src2"
+ check_err $? "(S, G) entry for source $src2 not created after
replace"
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -q "src
$src3"
+ check_err $? "(S, G) entry for source $src3 not created after
replace"
+
+ bridge mdb replace dev br0 port $swp1 grp $grp temp vid 10 \
+ filter_mode exclude source_list $src1,$src3
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -q "src
$src1"
+ check_err $? "(S, G) entry for source $src1 not created after second
replace"
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -q "src
$src2"
+ check_fail $? "(S, G) entry for source $src2 created after second
replace"
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -q "src
$src3"
+ check_err $? "(S, G) entry for source $src3 not created after second
replace"
+
+ bridge mdb del dev br0 port $swp1 grp $grp vid 10
+
+ # Check that protocol can be modified.
+ bridge mdb add dev br0 port $swp1 grp $grp temp vid 10 \
+ filter_mode exclude source_list $src1 proto zebra
+
+ bridge mdb replace dev br0 port $swp1 grp $grp temp vid 10 \
+ filter_mode exclude source_list $src1 proto bgp
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep -v
"src" | \
+ grep -q "bgp"
+ check_err $? "(*, G) protocol not changed to \"bgp\" after
replace"
+ bridge -d mdb show dev br0 vid 10 | grep "$grp" | grep
"src" | \
+ grep -q "bgp"
+ check_err $? "(S, G) protocol not changed to \"bgp\" after
replace"
+
+ bridge mdb del dev br0 port $swp1 grp $grp vid 10
+
+ ## Star exclude tests.
+
+ # Check star exclude functionality. When adding a new EXCLUDE (*, G),
+ # it needs to be also added to all (S, G) entries for proper
+ # replication.
+ bridge mdb add dev br0 port $swp2 grp $grp vid 10 \
+ filter_mode include source_list $src1
+ bridge mdb add dev br0 port $swp1 grp $grp vid 10
+ bridge -d mdb show dev br0 vid 10 | grep "$swp1" | grep
"$grp" | \
+ grep "$src1" | grep -q "added_by_star_ex"
+ check_err $? "\"added_by_star_ex\" entry not created after
adding (*, G) entry"
+ bridge mdb del dev br0 port $swp1 grp $grp vid 10
+ bridge mdb del dev br0 port $swp2 grp $grp src $src1 vid 10
+
+ ## Error cases tests.
+
+ bridge mdb add dev br0 port $swp1 grp $invalid_grp vid 10 &> /dev/null
+ check_fail $? "Managed to add an entry with an invalid group"
+
+ bridge mdb add dev br0 port $swp1 grp $grp vid 10 filter_mode include \
+ &> /dev/null
+ check_fail $? "Managed to add an INCLUDE entry with an empty source
list"
+
+ bridge mdb add dev br0 port $swp1 grp $grp vid 10 filter_mode include \
+ source_list $grp &> /dev/null
+ check_fail $? "Managed to add an entry with an invalid source in source
list"
+
+ bridge mdb add dev br0 port $swp1 grp $grp vid 10 \
+ source_list $src &> /dev/null
+ check_fail $? "Managed to add an entry with a source list and no filter
mode"
+
+ bridge mdb add dev br0 port $swp1 grp $grp vid 10 filter_mode include \
+ source_list $src1
+ bridge mdb add dev br0 port $swp1 grp $grp vid 10 filter_mode exclude \
+ source_list $src1 &> /dev/null
+ check_fail $? "Managed to replace an entry without using replace"
+ bridge mdb del dev br0 port $swp1 grp $grp vid 10
+
+ bridge mdb add dev br0 port $swp1 grp $grp src $src2 vid 10
+ bridge mdb add dev br0 port $swp1 grp $grp vid 10 filter_mode include \
+ source_list $src1,$src2,$src3 &> /dev/null
+ check_fail $? "Managed to add a source that already has a forwarding
entry"
+ bridge mdb del dev br0 port $swp1 grp $grp src $src2 vid 10
+
+ # Check maximum number of sources.
+ bridge mdb add dev br0 port $swp1 grp $grp vid 10 filter_mode exclude \
+ source_list $(src_list_create $src_prefix $max_srcs)
+ num_srcs=$(bridge -d mdb show dev br0 vid 10 | grep "$grp" | \
+ grep "src" | wc -l)
+ [[ $num_srcs -eq $max_srcs ]]
+ check_err $? "Failed to configure maximum number of sources
($max_srcs)"
+ bridge mdb del dev br0 port $swp1 grp $grp vid 10
+
+ bridge mdb add dev br0 port $swp1 grp $grp vid 10 filter_mode exclude \
+ source_list $(src_list_create $src_prefix $((max_srcs + 1))) \
+ &> /dev/null
+ check_fail $? "Managed to exceed maximum number of sources
($max_srcs)"
+
+ log_test "$name (*, G) port group entries configuration tests"
+}
+
+cfg_test_port_ip_star_g()
+{
+ echo
+ log_info "# Port group entries configuration tests - (*, G)"
+
+ cfg_test_port_common "IPv4 (*, G)" "grp 239.1.1.1"
+ cfg_test_port_common "IPv6 (*, G)" "grp ff0e::1"
+ __cfg_test_port_ip_star_g "IPv4" "239.1.1.1"
"224.0.0.1" "192.0.2."
+ __cfg_test_port_ip_star_g "IPv6" "ff0e::1"
"ff02::1" "2001:db8:1::"
+}
+
+__cfg_test_port_ip_sg()
+{
+ local name=$1; shift
+ local grp=$1; shift
+ local src=$1; shift
+ local grp_key="grp $grp src $src"
+
+ RET=0
+
+ bridge mdb add dev br0 port $swp1 $grp_key vid 10
+ bridge -d mdb show dev br0 vid 10 | grep "$grp_key" | grep -q
"include"
+ check_err $? "Default filter mode is not \"include\""
+ bridge mdb del dev br0 port $swp1 $grp_key vid 10
+
+ # Check that entries can be added as both permanent and temp and that
+ # group timer is set correctly.
+ bridge mdb add dev br0 port $swp1 $grp_key permanent vid 10
+ bridge -d mdb show dev br0 vid 10 | grep "$grp_key" | \
+ grep -q "permanent"
+ check_err $? "Entry not added as \"permanent\" when
should"
+ bridge -d -s mdb show dev br0 vid 10 | grep "$grp_key" | \
+ grep -q "0.00"
+ check_err $? "\"permanent\" entry has a pending group
timer"
+ bridge mdb del dev br0 port $swp1 $grp_key vid 10
+
+ bridge mdb add dev br0 port $swp1 $grp_key temp vid 10
+ bridge -d mdb show dev br0 vid 10 | grep "$grp_key" | \
+ grep -q "temp"
+ check_err $? "Entry not added as \"temp\" when should"
+ bridge -d -s mdb show dev br0 vid 10 | grep "$grp_key" | \
+ grep -q "0.00"
+ check_fail $? "\"temp\" entry has an unpending group
timer"
+ bridge mdb del dev br0 port $swp1 $grp_key vid 10
+
+ # Check error cases.
+ bridge mdb add dev br0 port $swp1 $grp_key vid 10 \
+ filter_mode include &> /dev/null
+ check_fail $? "Managed to add an entry with a filter mode"
+
+ bridge mdb add dev br0 port $swp1 $grp_key vid 10 \
+ filter_mode include source_list $src &> /dev/null
+ check_fail $? "Managed to add an entry with a source list"
+
+ bridge mdb add dev br0 port $swp1 grp $grp src $grp vid 10 &> /dev/null
+ check_fail $? "Managed to add an entry with an invalid source"
+
+ bridge mdb add dev br0 port $swp1 $grp_key vid 10 temp
+ bridge mdb add dev br0 port $swp1 $grp_key vid 10 permanent &>
/dev/null
+ check_fail $? "Managed to replace an entry without using replace"
+ bridge mdb del dev br0 port $swp1 $grp_key vid 10
+
+ # Check that we can replace available attributes.
+ bridge mdb add dev br0 port $swp1 $grp_key vid 10 proto 123
+ bridge mdb replace dev br0 port $swp1 $grp_key vid 10 proto 111
+ bridge -d mdb show dev br0 vid 10 | grep "$grp_key" | \
+ grep -q "111"
+ check_err $? "Failed to replace protocol"
+
+ bridge mdb replace dev br0 port $swp1 $grp_key vid 10 permanent
+ bridge -d mdb show dev br0 vid 10 | grep "$grp_key" | \
+ grep -q "permanent"
+ check_err $? "Entry not marked as \"permanent\" after
replace"
+ bridge -d -s mdb show dev br0 vid 10 | grep "$grp_key" | \
+ grep -q "0.00"
+ check_err $? "Entry has a pending group timer after replace"
+
+ bridge mdb replace dev br0 port $swp1 $grp_key vid 10 temp
+ bridge -d mdb show dev br0 vid 10 | grep "$grp_key" | \
+ grep -q "temp"
+ check_err $? "Entry not marked as \"temp\" after replace"
+ bridge -d -s mdb show dev br0 vid 10 | grep "$grp_key" | \
+ grep -q "0.00"
+ check_fail $? "Entry has an unpending group timer after replace"
+ bridge mdb del dev br0 port $swp1 $grp_key vid 10
+
+ # Check star exclude functionality. When adding a (S, G), all matching
+ # (*, G) ports need to be added to it.
+ bridge mdb add dev br0 port $swp2 grp $grp vid 10
+ bridge mdb add dev br0 port $swp1 $grp_key vid 10
+ bridge mdb show dev br0 vid 10 | grep "$grp_key" | grep $swp2 | \
+ grep -q "added_by_star_ex"
+ check_err $? "\"added_by_star_ex\" entry not created after
adding (S, G) entry"
+ bridge mdb del dev br0 port $swp1 $grp_key vid 10
+ bridge mdb del dev br0 port $swp2 grp $grp vid 10
+
+ log_test "$name (S, G) port group entries configuration tests"
+}
+
+cfg_test_port_ip_sg()
+{
+ echo
+ log_info "# Port group entries configuration tests - (S, G)"
+
+ cfg_test_port_common "IPv4 (S, G)" "grp 239.1.1.1 src
192.0.2.1"
+ cfg_test_port_common "IPv6 (S, G)" "grp ff0e::1 src
2001:db8:1::1"
+ __cfg_test_port_ip_sg "IPv4" "239.1.1.1"
"192.0.2.1"
+ __cfg_test_port_ip_sg "IPv6" "ff0e::1"
"2001:db8:1::1"
+}
+
+cfg_test_port_ip()
+{
+ cfg_test_port_ip_star_g
+ cfg_test_port_ip_sg
+}
+
+__cfg_test_port_l2()
+{
+ local grp="01:02:03:04:05:06"
+
+ RET=0
+
+ bridge meb add dev br0 port $swp grp 00:01:02:03:04:05 \
+ permanent vid 10 &> /dev/null
+ check_fail $? "Managed to add an entry with unicast MAC"
+
+ bridge mdb add dev br0 port $swp grp $grp src 00:01:02:03:04:05 \
+ permanent vid 10 &> /dev/null
+ check_fail $? "Managed to add an entry with a source"
+
+ bridge mdb add dev br0 port $swp1 grp $grp permanent vid 10 \
+ filter_mode include &> /dev/null
+ check_fail $? "Managed to add an entry with a filter mode"
+
+ bridge mdb add dev br0 port $swp1 grp $grp permanent vid 10 \
+ source_list 00:01:02:03:04:05 &> /dev/null
+ check_fail $? "Managed to add an entry with a source list"
+
+ log_test "L2 (*, G) port group entries configuration tests"
+}
+
+cfg_test_port_l2()
+{
+ echo
+ log_info "# Port group entries configuration tests - L2"
+
+ cfg_test_port_common "L2 (*, G)" "grp 01:02:03:04:05:06"
+ __cfg_test_port_l2
+}
+
+# Check configuration of regular (port) entries of all types.
+cfg_test_port()
+{
+ cfg_test_port_ip
+ cfg_test_port_l2
+}
+
+cfg_test()
+{
+ cfg_test_host
+ cfg_test_port
+}
+
+__fwd_test_host_ip()
+{
+ local grp=$1; shift
+ local src=$1; shift
+ local mode=$1; shift
+ local name
+ local eth_type
+
+ RET=0
+
+ if [[ $mode == "-4" ]]; then
+ name="IPv4"
+ eth_type="ipv4"
+ else
+ name="IPv6"
+ eth_type="ipv6"
+ fi
+
+ tc filter add dev br0 ingress protocol 802.1q pref 1 handle 1 flower \
+ vlan_ethtype $eth_type vlan_id 10 dst_ip $grp src_ip $src \
+ action drop
+
+ # Packet should only be flooded to multicast router ports when there is
+ # no matching MDB entry. The bridge is not configured as a multicast
+ # router port.
+ $MZ $mode $h1.10 -c 1 -p 128 -A $src -B $grp -t udp -q
+ tc_check_packets "dev br0 ingress" 1 0
+ check_err $? "Packet locally received after flood"
+
+ # Install a regular port group entry and expect the packet to not be
+ # locally received.
+ bridge mdb add dev br0 port $swp2 grp $grp temp vid 10
+ $MZ $mode $h1.10 -c 1 -p 128 -A $src -B $grp -t udp -q
+ tc_check_packets "dev br0 ingress" 1 0
+ check_err $? "Packet locally received after installing a regular
entry"
+
+ # Add a host entry and expect the packet to be locally received.
+ bridge mdb add dev br0 port br0 grp $grp temp vid 10
+ $MZ $mode $h1.10 -c 1 -p 128 -A $src -B $grp -t udp -q
+ tc_check_packets "dev br0 ingress" 1 1
+ check_err $? "Packet not locally received after adding a host entry"
+
+ # Remove the host entry and expect the packet to not be locally
+ # received.
+ bridge mdb del dev br0 port br0 grp $grp vid 10
+ $MZ $mode $h1.10 -c 1 -p 128 -A $src -B $grp -t udp -q
+ tc_check_packets "dev br0 ingress" 1 1
+ check_err $? "Packet locally received after removing a host entry"
+
+ bridge mdb del dev br0 port $swp2 grp $grp vid 10
+
+ tc filter del dev br0 ingress protocol 802.1q pref 1 handle 1 flower
+
+ log_test "$name host entries forwarding tests"
+}
+
+fwd_test_host_ip()
+{
+ __fwd_test_host_ip "239.1.1.1" "192.0.2.1" "-4"
+ __fwd_test_host_ip "ff0e::1" "2001:db8:1::1"
"-6"
+}
+
+fwd_test_host_l2()
+{
+ local dmac=01:02:03:04:05:06
+
+ RET=0
+
+ tc filter add dev br0 ingress protocol all pref 1 handle 1 flower \
+ dst_mac $dmac action drop
+
+ # Packet should be flooded and locally received when there is no
+ # matching MDB entry.
+ $MZ $h1.10 -c 1 -p 128 -a own -b $dmac -q
+ tc_check_packets "dev br0 ingress" 1 1
+ check_err $? "Packet not locally received after flood"
+
+ # Install a regular port group entry and expect the packet to not be
+ # locally received.
+ bridge mdb add dev br0 port $swp2 grp $dmac permanent vid 10
+ $MZ $h1.10 -c 1 -p 128 -a own -b $dmac -q
+ tc_check_packets "dev br0 ingress" 1 1
+ check_err $? "Packet locally received after installing a regular
entry"
+
+ # Add a host entry and expect the packet to be locally received.
+ bridge mdb add dev br0 port br0 grp $dmac permanent vid 10
+ $MZ $h1.10 -c 1 -p 128 -a own -b $dmac -q
+ tc_check_packets "dev br0 ingress" 1 2
+ check_err $? "Packet not locally received after adding a host entry"
+
+ # Remove the host entry and expect the packet to not be locally
+ # received.
+ bridge mdb del dev br0 port br0 grp $dmac permanent vid 10
+ $MZ $h1.10 -c 1 -p 128 -a own -b $dmac -q
+ tc_check_packets "dev br0 ingress" 1 2
+ check_err $? "Packet locally received after removing a host entry"
+
+ bridge mdb del dev br0 port $swp2 grp $dmac permanent vid 10
+
+ tc filter del dev br0 ingress protocol all pref 1 handle 1 flower
+
+ log_test "L2 host entries forwarding tests"
+}
+
+fwd_test_host()
+{
+ # Disable multicast router on the bridge to ensure that packets are
+ # only locally received when a matching host entry is present.
+ ip link set dev br0 type bridge mcast_router 0
+
+ fwd_test_host_ip
+ fwd_test_host_l2
+
+ ip link set dev br0 type bridge mcast_router 1
+}
+
+__fwd_test_port_ip()
+{
+ local grp=$1; shift
+ local valid_src=$1; shift
+ local invalid_src=$1; shift
+ local mode=$1; shift
+ local filter_mode=$1; shift
+ local name
+ local eth_type
+ local src_list
+
+ RET=0
+
+ if [[ $mode == "-4" ]]; then
+ name="IPv4"
+ eth_type="ipv4"
+ else
+ name="IPv6"
+ eth_type="ipv6"
+ fi
+
+ # The valid source is the one we expect to get packets from after
+ # adding the entry.
+ if [[ $filter_mode == "include" ]]; then
+ src_list=$valid_src
+ else
+ src_list=$invalid_src
+ fi
+
+ tc filter add dev $h2 ingress protocol 802.1q pref 1 handle 1 flower \
+ vlan_ethtype $eth_type vlan_id 10 dst_ip $grp \
+ src_ip $valid_src action drop
+ tc filter add dev $h2 ingress protocol 802.1q pref 1 handle 2 flower \
+ vlan_ethtype $eth_type vlan_id 10 dst_ip $grp \
+ src_ip $invalid_src action drop
+
+ $MZ $mode $h1.10 -c 1 -p 128 -A $valid_src -B $grp -t udp -q
+ tc_check_packets "dev $h2 ingress" 1 0
+ check_err $? "Packet from valid source received on H2 before adding
entry"
+
+ $MZ $mode $h1.10 -c 1 -p 128 -A $invalid_src -B $grp -t udp -q
+ tc_check_packets "dev $h2 ingress" 2 0
+ check_err $? "Packet from invalid source received on H2 before adding
entry"
+
+ bridge mdb add dev br0 port $swp2 grp $grp vid 10 \
+ filter_mode $filter_mode source_list $src_list
+
+ $MZ $mode $h1.10 -c 1 -p 128 -A $valid_src -B $grp -t udp -q
+ tc_check_packets "dev $h2 ingress" 1 1
+ check_err $? "Packet from valid source not received on H2 after adding
entry"
+
+ $MZ $mode $h1.10 -c 1 -p 128 -A $invalid_src -B $grp -t udp -q
+ tc_check_packets "dev $h2 ingress" 2 0
+ check_err $? "Packet from invalid source received on H2 after adding
entry"
+
+ bridge mdb replace dev br0 port $swp2 grp $grp vid 10 \
+ filter_mode exclude
+
+ $MZ $mode $h1.10 -c 1 -p 128 -A $valid_src -B $grp -t udp -q
+ tc_check_packets "dev $h2 ingress" 1 2
+ check_err $? "Packet from valid source not received on H2 after allowing
all sources"
+
+ $MZ $mode $h1.10 -c 1 -p 128 -A $invalid_src -B $grp -t udp -q
+ tc_check_packets "dev $h2 ingress" 2 1
+ check_err $? "Packet from invalid source not received on H2 after
allowing all sources"
+
+ bridge mdb del dev br0 port $swp2 grp $grp vid 10
+
+ $MZ $mode $h1.10 -c 1 -p 128 -A $valid_src -B $grp -t udp -q
+ tc_check_packets "dev $h2 ingress" 1 2
+ check_err $? "Packet from valid source received on H2 after deleting
entry"
+
+ $MZ $mode $h1.10 -c 1 -p 128 -A $invalid_src -B $grp -t udp -q
+ tc_check_packets "dev $h2 ingress" 2 1
+ check_err $? "Packet from invalid source received on H2 after deleting
entry"
+
+ tc filter del dev $h2 ingress protocol 802.1q pref 1 handle 2 flower
+ tc filter del dev $h2 ingress protocol 802.1q pref 1 handle 1 flower
+
+ log_test "$name port group \"$filter_mode\" entries forwarding
tests"
+}
+
+fwd_test_port_ip()
+{
+ __fwd_test_port_ip "239.1.1.1" "192.0.2.1"
"192.0.2.2" "-4" "exclude"
+ __fwd_test_port_ip "ff0e::1" "2001:db8:1::1"
"2001:db8:1::2" "-6" \
+ "exclude"
+ __fwd_test_port_ip "239.1.1.1" "192.0.2.1"
"192.0.2.2" "-4" "include"
+ __fwd_test_port_ip "ff0e::1" "2001:db8:1::1"
"2001:db8:1::2" "-6" \
+ "include"
+}
+
+fwd_test_port_l2()
+{
+ local dmac=01:02:03:04:05:06
+
+ RET=0
+
+ tc filter add dev $h2 ingress protocol all pref 1 handle 1 flower \
+ dst_mac $dmac action drop
+
+ $MZ $h1.10 -c 1 -p 128 -a own -b $dmac -q
+ tc_check_packets "dev $h2 ingress" 1 0
+ check_err $? "Packet received on H2 before adding entry"
+
+ bridge mdb add dev br0 port $swp2 grp $dmac permanent vid 10
+ $MZ $h1.10 -c 1 -p 128 -a own -b $dmac -q
+ tc_check_packets "dev $h2 ingress" 1 1
+ check_err $? "Packet not received on H2 after adding entry"
+
+ bridge mdb del dev br0 port $swp2 grp $dmac permanent vid 10
+ $MZ $h1.10 -c 1 -p 128 -a own -b $dmac -q
+ tc_check_packets "dev $h2 ingress" 1 1
+ check_err $? "Packet received on H2 after deleting entry"
+
+ tc filter del dev $h2 ingress protocol all pref 1 handle 1 flower
+
+ log_test "L2 port entries forwarding tests"
+}
+
+fwd_test_port()
+{
+ # Disable multicast flooding to ensure that packets are only forwarded
+ # out of a port when a matching port group entry is present.
+ bridge link set dev $swp2 mcast_flood off
+
+ fwd_test_port_ip
+ fwd_test_port_l2
+
+ bridge link set dev $swp2 mcast_flood on
+}
+
+fwd_test()
+{
+ echo
+ log_info "# Forwarding tests"
+
+ # Forwarding according to MDB entries only takes place when the bridge
+ # detects that there is a valid querier in the network. Set the bridge
+ # as the querier and assign it a valid IPv6 link-local address to be
+ # used as the source address for MLD queries.
+ ip -6 address add fe80::1/64 nodad dev br0
+ ip link set dev br0 type bridge mcast_querier 1
+ # Wait the default Query Response Interval (10 seconds) for the bridge
+ # to determine that there are no other queriers in the network.
+ sleep 10
+
+ fwd_test_host
+ fwd_test_port
+
+ ip link set dev br0 type bridge mcast_querier 0
+ ip -6 address del fe80::1/64 dev br0
+}
+
+igmpv3_is_in_get()
+{
+ local igmpv3
+
+ igmpv3=$(:
+ )"22:"$( : Type - Membership Report
+ )"00:"$( : Reserved
+ )"2a:f8:"$( : Checksum
+ )"00:00:"$( : Reserved
+ )"00:01:"$( : Number of Group Records
+ )"01:"$( : Record Type - IS_IN
+ )"00:"$( : Aux Data Len
+ )"00:01:"$( : Number of Sources
+ )"ef:01:01:01:"$( : Multicast Address - 239.1.1.1
+ )"c0:00:02:02"$( : Source Address - 192.0.2.2
+ )
+
+ echo $igmpv3
+}
+
+ctrl_igmpv3_is_in_test()
+{
+ RET=0
+
+ # Add a permanent entry and check that it is not affected by the
+ # received IGMP packet.
+ bridge mdb add dev br0 port $swp1 grp 239.1.1.1 permanent vid 10 \
+ filter_mode include source_list 192.0.2.1
+
+ # IS_IN ( 192.0.2.2 )
+ $MZ $h1.10 -c 1 -A 192.0.2.1 -B 239.1.1.1 \
+ -t ip proto=2,p=$(igmpv3_is_in_get) -q
+
+ bridge -d mdb show dev br0 vid 10 | grep 239.1.1.1 | grep -q 192.0.2.2
+ check_fail $? "Permanent entry affected by IGMP packet"
+
+ # Replace the permanent entry with a temporary one and check that after
+ # processing the IGMP packet, a new source is added to the list along
+ # with a new forwarding entry.
+ bridge mdb replace dev br0 port $swp1 grp 239.1.1.1 temp vid 10 \
+ filter_mode include source_list 192.0.2.1
+
+ # IS_IN ( 192.0.2.2 )
+ $MZ $h1.10 -c 1 -A 192.0.2.1 -B 239.1.1.1 \
+ -t ip proto=2,p=$(igmpv3_is_in_get) -q
+
+ bridge -d mdb show dev br0 vid 10 | grep 239.1.1.1 | grep -v "src" |
\
+ grep -q 192.0.2.2
+ check_err $? "Source not add to source list"
+
+ bridge -d mdb show dev br0 vid 10 | grep 239.1.1.1 | \
+ grep -q "src 192.0.2.2"
+ check_err $? "(S, G) entry not created for new source"
+
+ bridge mdb del dev br0 port $swp1 grp 239.1.1.1 vid 10
+
+ log_test "IGMPv3 MODE_IS_INCLUE tests"
+}
+
+mldv2_is_in_get()
+{
+ local hbh
+ local icmpv6
+
+ hbh=$(:
+ )"3a:"$( : Next Header - ICMPv6
+ )"00:"$( : Hdr Ext Len
+ )"00:00:00:00:00:00:"$( : Options and Padding
+ )
+
+ icmpv6=$(:
+ )"8f:"$( : Type - MLDv2 Report
+ )"00:"$( : Code
+ )"45:39:"$( : Checksum
+ )"00:00:"$( : Reserved
+ )"00:01:"$( : Number of Group Records
+ )"01:"$( : Record Type - IS_IN
+ )"00:"$( : Aux Data Len
+ )"00:01:"$( : Number of Sources
+ )"ff:0e:00:00:00:00:00:00:"$( : Multicast address - ff0e::1
+ )"00:00:00:00:00:00:00:01:"$( :
+ )"20:01:0d:b8:00:01:00:00:"$( : Source Address - 2001:db8:1::2
+ )"00:00:00:00:00:00:00:02:"$( :
+ )
+
+ echo ${hbh}${icmpv6}
+}
+
+ctrl_mldv2_is_in_test()
+{
+ RET=0
+
+ # Add a permanent entry and check that it is not affected by the
+ # received MLD packet.
+ bridge mdb add dev br0 port $swp1 grp ff0e::1 permanent vid 10 \
+ filter_mode include source_list 2001:db8:1::1
+
+ # IS_IN ( 2001:db8:1::2 )
+ $MZ -6 $h1.10 -c 1 -A fe80::1 -B ff0e::1 \
+ -t ip hop=1,next=0,p=$(mldv2_is_in_get) -q
+
+ bridge -d mdb show dev br0 vid 10 | grep ff0e::1 | \
+ grep -q 2001:db8:1::2
+ check_fail $? "Permanent entry affected by MLD packet"
+
+ # Replace the permanent entry with a temporary one and check that after
+ # processing the MLD packet, a new source is added to the list along
+ # with a new forwarding entry.
+ bridge mdb replace dev br0 port $swp1 grp ff0e::1 temp vid 10 \
+ filter_mode include source_list 2001:db8:1::1
+
+ # IS_IN ( 2001:db8:1::2 )
+ $MZ -6 $h1.10 -c 1 -A fe80::1 -B ff0e::1 \
+ -t ip hop=1,next=0,p=$(mldv2_is_in_get) -q
+
+ bridge -d mdb show dev br0 vid 10 | grep ff0e::1 | grep -v "src" | \
+ grep -q 2001:db8:1::2
+ check_err $? "Source not add to source list"
+
+ bridge -d mdb show dev br0 vid 10 | grep ff0e::1 | \
+ grep -q "src 2001:db8:1::2"
+ check_err $? "(S, G) entry not created for new source"
+
+ bridge mdb del dev br0 port $swp1 grp ff0e::1 vid 10
+
+ log_test "MLDv2 MODE_IS_INCLUDE tests"
+}
+
+ctrl_test()
+{
+ echo
+ log_info "# Control packets tests"
+
+ ctrl_igmpv3_is_in_test
+ ctrl_mldv2_is_in_test
+}
+
+trap cleanup EXIT
+
+setup_prepare
+setup_wait
+tests_run
+
+exit $EXIT_STATUS
--
2.37.3