Hi Tiemen,
One of the pre-requisites before setting up nfs-ganesha HA is to create
and mount shared_storage volume. Use below CLI for that
"gluster volume set all cluster.enable-shared-storage enable"
It shall create the volume and mount in all the nodes (including the
arbiter node). Note this volume shall be mounted on all the nodes of the
gluster storage pool (though in this case it may not be part of
nfs-ganesha cluster).
So instead of manually creating those directory paths, please use above
CLI and try re-configuring the setup.
Thanks,
Soumya
On 09/18/2015 07:29 PM, Tiemen Ruiten wrote:> Hello Kaleb,
>
> I don't:
>
> # Name of the HA cluster created.
> # must be unique within the subnet
> HA_NAME="rd-ganesha-ha"
> #
> # The gluster server from which to mount the shared data volume.
> HA_VOL_SERVER="iron"
> #
> # N.B. you may use short names or long names; you may not use IP addrs.
> # Once you select one, stay with it as it will be mildly unpleasant to
> # clean up if you switch later on. Ensure that all names - short and/or
> # long - are in DNS or /etc/hosts on all machines in the cluster.
> #
> # The subset of nodes of the Gluster Trusted Pool that form the ganesha
> # HA cluster. Hostname is specified.
> HA_CLUSTER_NODES="cobalt,iron"
> #HA_CLUSTER_NODES="server1.lab.redhat.com
> <http://server1.lab.redhat.com>,server2.lab.redhat.com
> <http://server2.lab.redhat.com>,..."
> #
> # Virtual IPs for each of the nodes specified above.
> VIP_server1="10.100.30.101"
> VIP_server2="10.100.30.102"
> #VIP_server1_lab_redhat_com="10.0.2.1"
> #VIP_server2_lab_redhat_com="10.0.2.2"
>
> hosts cobalt & iron are the data nodes, the arbiter ip/hostname (neon)
> isn't mentioned anywhere in this config file.
>
>
> On 18 September 2015 at 15:56, Kaleb S. KEITHLEY <kkeithle at redhat.com
> <mailto:kkeithle at redhat.com>> wrote:
>
> On 09/18/2015 09:46 AM, Tiemen Ruiten wrote:
> > Hello,
> >
> > I have a Gluster cluster with a single replica 3, arbiter 1 volume
(so
> > two nodes with actual data, one arbiter node). I would like to
setup
> > NFS-Ganesha HA for this volume but I'm having some
difficulties.
> >
> > - I needed to create a directory /var/run/gluster/shared_storage
> > manually on all nodes, or the command 'gluster nfs-ganesha
enable would
> > fail with the following error:
> > [2015-09-18 13:13:34.690416] E [MSGID: 106032]
> > [glusterd-ganesha.c:708:pre_setup] 0-THIS->name: mkdir() failed
on path
> > /var/run/gluster/shared_storage/nfs-ganesha, [No such file or
directory]
> >
> > - Then I found out that the command connects to the arbiter node
as
> > well, but obviously I don't want to set up NFS-Ganesha there.
Is it
> > actually possible to setup NFS-Ganesha HA with an arbiter node? If
it's
> > possible, is there any documentation on how to do that?
> >
>
> Please send the /etc/ganesha/ganesha-ha.conf file you're using.
>
> Probably you have included the arbiter in your HA config; that would be
> a mistake.
>
> --
>
> Kaleb
>
>
>
>
> --
> Tiemen Ruiten
> Systems Engineer
> R&D Media
>
>
> _______________________________________________
> Gluster-users mailing list
> Gluster-users at gluster.org
> http://www.gluster.org/mailman/listinfo/gluster-users
>