Hi Sandy, Please can you provide the output from an *i**fconfig -a* command? This should give an idea of what is going on. Turning off IPv6 will not be necessary if you can find the actual cause of the problem. You would not get this error message if you only have a link local address configured on your interface. You must have some form of global address. Also, the IPv6 address is that of git.samba.org not samba.org. You could try: *traceroute6 git.samba.org.* Best Regards, David ------------------------------------------------------------------------ Dr David Holder CEng FIET MIEEE Erion Ltd, An Cala, Inverkirkaig, Lochinver, Sutherland, IV27 4LR, UK Reception: +44 (0)1422 207000 Direct Dial: +44 (0)131 2026317 http://www.erion.co.uk Registered in England and Wales. Registered Number 3521142 Registered Office: Newtons, 49 Coniscliffe Road, Darlington, County Durham, DL3 7EH, UK VAT Number: GB 698 3633 78 On 28/02/2015 18:38, Reindl Harald wrote:> > > Am 28.02.2015 um 19:13 schrieb sandy.napoles at eccmg.cupet.cu: >> I do not working with ipv6, I have disable, but I have the same error, I >> can read in internet that this ipv6 ip 2001:638:603:d06e::80:230: belong >> to url samba.org.... >> >> If I try to connect to this url using some navegator I connected >> perfect....but when I run git pull using command line I can not >> connect.. > > the question is *how* did you disable ipv6 - when ifconfig shows a > "link local" ipv6 address the stack is *not* entirely disabled > > [root at srv-rhsoft:~]$ ifconfig eth0 > eth0: flags=4419<UP,BROADCAST,RUNNING,PROMISC,MULTICAST> mtu 1500 > ether 24:be:05:1a:c0:27 txqueuelen 100 (Ethernet) > RX packets 2460 bytes 577531 (563.9 KiB) > RX errors 0 dropped 0 overruns 0 frame 0 > TX packets 8722 bytes 1981928 (1.8 MiB) > TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 > device interrupt 20 memory 0xf7e00000-f7e20000 > >>> Am 28.02.2015 um 15:37 schrieb sandy.napoles at eccmg.cupet.cu: >>>> Hello list, Iam using samba4 as Domain Controller my verion Version >>>> 4.3.0pre1-GIT-068f9e2, but I have a little problem when I going to >>>> update >>>> using GIT PULL I have this error >>>> >>>> error: Failed to connect to 2001:638:603:d06e::80:230: Network is >>>> unreachable while accessing http://git.samba.org/samba.git/info/refs >>>> fatal: HTTP request failed >>>> >>>> some body can helpme >>> >>> do you have working ipv6? >>> if not disable it via sysctl.conf >>> >>> net.ipv6.conf.all.disable_ipv6=1 >>> net.ipv6.conf.default.disable_ipv6=1 >>> >>> that above is most likely because the link-local address if the ipv6 >>> stack is enabled and some piece of software thinks it's useable >>> >>> -- >>> To unsubscribe from this list go to the following URL and read the >>> instructions: https://lists.samba.org/mailman/options/samba > > >
eth0 Link encap:Ethernet HWaddr d0:27:88:64:e4:01
inet addr:172.18.70.100 Mask:255.255.255.224
inet6 addr: fe80::d227:88ff:fe64:e401/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1413908 errors:0 dropped:0 overruns:0 frame:0
TX packets:447039 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1693689457 (1.5 GiB) TX bytes:52974612 (50.5 MiB)
Interrupt:43 Base address:0xc000
traceroute6 git.samba.org
traceroute to git.samba.org (2001:638:603:d06e::80:230), 30 hops max, 80
byte packets
connect: Network is unreachable
> Hi Sandy,
>
> Please can you provide the output from an *i**fconfig -a* command?
>
> This should give an idea of what is going on. Turning off IPv6 will not
> be necessary if you can find the actual cause of the problem.
>
> You would not get this error message if you only have a link local
> address configured on your interface. You must have some form of global
> address.
>
> Also, the IPv6 address is that of git.samba.org not samba.org. You could
> try:
>
> *traceroute6 git.samba.org.*
>
> Best Regards,
> David
> ------------------------------------------------------------------------
> Dr David Holder CEng FIET MIEEE
>
> Erion Ltd, An Cala, Inverkirkaig, Lochinver, Sutherland, IV27 4LR, UK
>
> Reception: +44 (0)1422 207000
>
> Direct Dial: +44 (0)131 2026317
>
> http://www.erion.co.uk
>
>
> Registered in England and Wales. Registered Number 3521142
> Registered Office: Newtons, 49 Coniscliffe Road, Darlington, County
> Durham, DL3 7EH, UK
> VAT Number: GB 698 3633 78
>
> On 28/02/2015 18:38, Reindl Harald wrote:
>>
>>
>> Am 28.02.2015 um 19:13 schrieb sandy.napoles at eccmg.cupet.cu:
>>> I do not working with ipv6, I have disable, but I have the same
error,
>>> I
>>> can read in internet that this ipv6 ip 2001:638:603:d06e::80:230:
>>> belong
>>> to url samba.org....
>>>
>>> If I try to connect to this url using some navegator I connected
>>> perfect....but when I run git pull using command line I can not
>>> connect..
>>
>> the question is *how* did you disable ipv6 - when ifconfig shows a
>> "link local" ipv6 address the stack is *not* entirely
disabled
>>
>> [root at srv-rhsoft:~]$ ifconfig eth0
>> eth0: flags=4419<UP,BROADCAST,RUNNING,PROMISC,MULTICAST> mtu 1500
>> ether 24:be:05:1a:c0:27 txqueuelen 100 (Ethernet)
>> RX packets 2460 bytes 577531 (563.9 KiB)
>> RX errors 0 dropped 0 overruns 0 frame 0
>> TX packets 8722 bytes 1981928 (1.8 MiB)
>> TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
>> device interrupt 20 memory 0xf7e00000-f7e20000
>>
>>>> Am 28.02.2015 um 15:37 schrieb sandy.napoles at eccmg.cupet.cu:
>>>>> Hello list, Iam using samba4 as Domain Controller my verion
Version
>>>>> 4.3.0pre1-GIT-068f9e2, but I have a little problem when I
going to
>>>>> update
>>>>> using GIT PULL I have this error
>>>>>
>>>>> error: Failed to connect to 2001:638:603:d06e::80:230:
Network is
>>>>> unreachable while accessing
http://git.samba.org/samba.git/info/refs
>>>>> fatal: HTTP request failed
>>>>>
>>>>> some body can helpme
>>>>
>>>> do you have working ipv6?
>>>> if not disable it via sysctl.conf
>>>>
>>>> net.ipv6.conf.all.disable_ipv6=1
>>>> net.ipv6.conf.default.disable_ipv6=1
>>>>
>>>> that above is most likely because the link-local address if the
ipv6
>>>> stack is enabled and some piece of software thinks it's
useable
>>>>
>>>> --
>>>> To unsubscribe from this list go to the following URL and read
the
>>>> instructions: https://lists.samba.org/mailman/options/samba
>>
>>
>>
>
> --
> To unsubscribe from this list go to the following URL and read the
> instructions: https://lists.samba.org/mailman/options/samba
>
if you use ufw firewall and you have disabled the IPV6 in /etc/default/ufw then whats below is correct. if you enable ipv6 in ufw... below should work. you can try these in : sysctl.conf net.ipv6.conf.all.accept_ra = 1 net.ipv6.conf.all.autoconf = 1 net.ipv6.conf.eth0.accept_ra = 1 net.ipv6.conf.eth0.autoconf = 1 Greetz, Louis>-----Oorspronkelijk bericht----- >Van: sandy.napoles at eccmg.cupet.cu >[mailto:samba-bounces at lists.samba.org] Namens >sandy.napoles at eccmg.cupet.cu >Verzonden: maandag 2 maart 2015 14:10 >Aan: samba at lists.samba.org >Onderwerp: Re: [Samba] Update > >eth0 Link encap:Ethernet HWaddr d0:27:88:64:e4:01 > inet addr:172.18.70.100 Mask:255.255.255.224 > inet6 addr: fe80::d227:88ff:fe64:e401/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:1413908 errors:0 dropped:0 overruns:0 frame:0 > TX packets:447039 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:1693689457 (1.5 GiB) TX bytes:52974612 (50.5 MiB) > Interrupt:43 Base address:0xc000 > > >traceroute6 git.samba.org >traceroute to git.samba.org (2001:638:603:d06e::80:230), 30 >hops max, 80 >byte packets >connect: Network is unreachable > > > > >> Hi Sandy, >> >> Please can you provide the output from an *i**fconfig -a* command? >> >> This should give an idea of what is going on. Turning off >IPv6 will not >> be necessary if you can find the actual cause of the problem. >> >> You would not get this error message if you only have a link local >> address configured on your interface. You must have some >form of global >> address. >> >> Also, the IPv6 address is that of git.samba.org not >samba.org. You could >> try: >> >> *traceroute6 git.samba.org.* >> >> Best Regards, >> David >> >--------------------------------------------------------------- >--------- >> Dr David Holder CEng FIET MIEEE >> >> Erion Ltd, An Cala, Inverkirkaig, Lochinver, Sutherland, IV27 4LR, UK >> >> Reception: +44 (0)1422 207000 >> >> Direct Dial: +44 (0)131 2026317 >> >> http://www.erion.co.uk >> >> >> Registered in England and Wales. Registered Number 3521142 >> Registered Office: Newtons, 49 Coniscliffe Road, Darlington, County >> Durham, DL3 7EH, UK >> VAT Number: GB 698 3633 78 >> >> On 28/02/2015 18:38, Reindl Harald wrote: >>> >>> >>> Am 28.02.2015 um 19:13 schrieb sandy.napoles at eccmg.cupet.cu: >>>> I do not working with ipv6, I have disable, but I have the >same error, >>>> I >>>> can read in internet that this ipv6 ip 2001:638:603:d06e::80:230: >>>> belong >>>> to url samba.org.... >>>> >>>> If I try to connect to this url using some navegator I connected >>>> perfect....but when I run git pull using command line I can not >>>> connect.. >>> >>> the question is *how* did you disable ipv6 - when ifconfig shows a >>> "link local" ipv6 address the stack is *not* entirely disabled >>> >>> [root at srv-rhsoft:~]$ ifconfig eth0 >>> eth0: flags=4419<UP,BROADCAST,RUNNING,PROMISC,MULTICAST> mtu 1500 >>> ether 24:be:05:1a:c0:27 txqueuelen 100 (Ethernet) >>> RX packets 2460 bytes 577531 (563.9 KiB) >>> RX errors 0 dropped 0 overruns 0 frame 0 >>> TX packets 8722 bytes 1981928 (1.8 MiB) >>> TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 >>> device interrupt 20 memory 0xf7e00000-f7e20000 >>> >>>>> Am 28.02.2015 um 15:37 schrieb sandy.napoles at eccmg.cupet.cu: >>>>>> Hello list, Iam using samba4 as Domain Controller my >verion Version >>>>>> 4.3.0pre1-GIT-068f9e2, but I have a little problem when >I going to >>>>>> update >>>>>> using GIT PULL I have this error >>>>>> >>>>>> error: Failed to connect to 2001:638:603:d06e::80:230: Network is >>>>>> unreachable while accessing >http://git.samba.org/samba.git/info/refs >>>>>> fatal: HTTP request failed >>>>>> >>>>>> some body can helpme >>>>> >>>>> do you have working ipv6? >>>>> if not disable it via sysctl.conf >>>>> >>>>> net.ipv6.conf.all.disable_ipv6=1 >>>>> net.ipv6.conf.default.disable_ipv6=1 >>>>> >>>>> that above is most likely because the link-local address >if the ipv6 >>>>> stack is enabled and some piece of software thinks it's useable >>>>> >>>>> -- >>>>> To unsubscribe from this list go to the following URL and read the >>>>> instructions: https://lists.samba.org/mailman/options/samba >>> >>> >>> >> >> -- >> To unsubscribe from this list go to the following URL and read the >> instructions: https://lists.samba.org/mailman/options/samba >> > > >-- >To unsubscribe from this list go to the following URL and read the >instructions: https://lists.samba.org/mailman/options/samba > >
Hi Sandy, Thanks! Curious. Do you have any other interfaces? ifconfig -a should show them all including loopback. What is puzzling me is that it should not even attempt to use IPv6 to reach a global address when it only has a link-local address. It should gracefully fall back to IPv4 (as per RFC 6724 or RFC 3484 depending on the kernel version). Since you have an IPv4 address and I assume an IPv4 connection, then this should work over IPv4. I'm assume that you do not have an /etc/gai.conf file installed? David ------------------------------------------------------------------------ Dr David Holder CEng FIET MIEEE Erion Ltd, An Cala, Inverkirkaig, Lochinver, Sutherland, IV27 4LR, UK Reception: +44 (0)1422 207000 Direct Dial: +44 (0)131 2026317 http://www.erion.co.uk Registered in England and Wales. Registered Number 3521142 Registered Office: Newtons, 49 Coniscliffe Road, Darlington, County Durham, DL3 7EH, UK VAT Number: GB 698 3633 78 On 02/03/2015 13:10, sandy.napoles at eccmg.cupet.cu wrote:> eth0 Link encap:Ethernet HWaddr d0:27:88:64:e4:01 > inet addr:172.18.70.100 Mask:255.255.255.224 > inet6 addr: fe80::d227:88ff:fe64:e401/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:1413908 errors:0 dropped:0 overruns:0 frame:0 > TX packets:447039 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:1693689457 (1.5 GiB) TX bytes:52974612 (50.5 MiB) > Interrupt:43 Base address:0xc000 > > > traceroute6 git.samba.org > traceroute to git.samba.org (2001:638:603:d06e::80:230), 30 hops max, 80 > byte packets > connect: Network is unreachable > > > > >> Hi Sandy, >> >> Please can you provide the output from an *i**fconfig -a* command? >> >> This should give an idea of what is going on. Turning off IPv6 will not >> be necessary if you can find the actual cause of the problem. >> >> You would not get this error message if you only have a link local >> address configured on your interface. You must have some form of global >> address. >> >> Also, the IPv6 address is that of git.samba.org not samba.org. You could >> try: >> >> *traceroute6 git.samba.org.* >> >> Best Regards, >> David >> ------------------------------------------------------------------------ >> Dr David Holder CEng FIET MIEEE >> >> Erion Ltd, An Cala, Inverkirkaig, Lochinver, Sutherland, IV27 4LR, UK >> >> Reception: +44 (0)1422 207000 >> >> Direct Dial: +44 (0)131 2026317 >> >> http://www.erion.co.uk >> >> >> Registered in England and Wales. Registered Number 3521142 >> Registered Office: Newtons, 49 Coniscliffe Road, Darlington, County >> Durham, DL3 7EH, UK >> VAT Number: GB 698 3633 78 >> >> On 28/02/2015 18:38, Reindl Harald wrote: >>> >>> Am 28.02.2015 um 19:13 schrieb sandy.napoles at eccmg.cupet.cu: >>>> I do not working with ipv6, I have disable, but I have the same error, >>>> I >>>> can read in internet that this ipv6 ip 2001:638:603:d06e::80:230: >>>> belong >>>> to url samba.org.... >>>> >>>> If I try to connect to this url using some navegator I connected >>>> perfect....but when I run git pull using command line I can not >>>> connect.. >>> the question is *how* did you disable ipv6 - when ifconfig shows a >>> "link local" ipv6 address the stack is *not* entirely disabled >>> >>> [root at srv-rhsoft:~]$ ifconfig eth0 >>> eth0: flags=4419<UP,BROADCAST,RUNNING,PROMISC,MULTICAST> mtu 1500 >>> ether 24:be:05:1a:c0:27 txqueuelen 100 (Ethernet) >>> RX packets 2460 bytes 577531 (563.9 KiB) >>> RX errors 0 dropped 0 overruns 0 frame 0 >>> TX packets 8722 bytes 1981928 (1.8 MiB) >>> TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 >>> device interrupt 20 memory 0xf7e00000-f7e20000 >>> >>>>> Am 28.02.2015 um 15:37 schrieb sandy.napoles at eccmg.cupet.cu: >>>>>> Hello list, Iam using samba4 as Domain Controller my verion Version >>>>>> 4.3.0pre1-GIT-068f9e2, but I have a little problem when I going to >>>>>> update >>>>>> using GIT PULL I have this error >>>>>> >>>>>> error: Failed to connect to 2001:638:603:d06e::80:230: Network is >>>>>> unreachable while accessing http://git.samba.org/samba.git/info/refs >>>>>> fatal: HTTP request failed >>>>>> >>>>>> some body can helpme >>>>> do you have working ipv6? >>>>> if not disable it via sysctl.conf >>>>> >>>>> net.ipv6.conf.all.disable_ipv6=1 >>>>> net.ipv6.conf.default.disable_ipv6=1 >>>>> >>>>> that above is most likely because the link-local address if the ipv6 >>>>> stack is enabled and some piece of software thinks it's useable >>>>> >>>>> -- >>>>> To unsubscribe from this list go to the following URL and read the >>>>> instructions: https://lists.samba.org/mailman/options/samba >>> >>> >> -- >> To unsubscribe from this list go to the following URL and read the >> instructions: https://lists.samba.org/mailman/options/samba >> >