similar to: CentOS/Xen PCI pass-through

testing, uname -ri 2.6.33-rc5-4-xen x86_64 rpm -qa | grep -i Xen-4 xen-4.0.0_20873_01-29.1.x86_64 cat test.cfg name = ''test'' builder = ''linux'' bootloader = ''/usr/lib/xen/boot/domUloader.py'' bootargs = ''--entry=xvda1:vmlinuz-xen,/boot/initrd-xen'' disk = [

Hi : I am trying to do PCIe passthrough on HVM domu. I have window XP as a HVM domu and xen-4.0. dom0 and domU (without device assign) works fine. I have more than one NIC card. I want to passthrough 03:00.0 to domu here are the list of my nic cards: lspci | grep -i eth 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)

Hi all!. First of all sorry about my English it''s not very fluid. I have a small server based upon Supermicro X7DBN (Chipset Intel® 5000P) motherboard and Intel Xeon E5320 (1,83Ghz) with 4Gb of FB-DIMM RAM. The OS is Debian Lenny in dom0 (2.6.26-2-xen-amd64) and Debian Lenny in domU (2.6.26-2-xen-amd64). Xen is 3.4.2 compiled from sources. The problem comes when I need to passthrough

This issue was brought up about a year and a half ago. So I''ll bring it up again and see if anything happens. I''ve got an infiniband network and am attempting to pass the infiniband card through the host and give it to the guest. I''m working with standard CentOS 5.2 on both guest and host with their provided xen (3.0.3 ish). I''ve also attempted to install the

This issue was brought up about a year and a half ago. So I''ll bring it up again and see if anything happens. I''ve got an infiniband network and am attempting to pass the infiniband card through the host and give it to the guest. I''m working with standard CentOS 5.2 on both guest and host with their provided xen (3.0.3 ish). I''ve also attempted to install the

Hello, I am desperately trying to get pci-passthrough to working. I want to pass a tg3 nic to domU. when booting domU I get a lot of messages: pcifront pci-0: pciback not responding!!! in domU, "ifconfig eth... adress up" hangs for 2 minutes, finally ifconfig -a shows a correct setting with no data transmitted rx/tx The IP Adress is being assigned, but there is no data transmission

Hello, I''m trying to add a USB dongle to my domU. I searched a lot and found an instruction (http://wiki.xen.org/xenwiki/XenUSBPassthrough.html). I added followings to domU''s cfg file: usb = 1 usbdevice = ''host:0925:1234'' But when i create my domU lsusb still doesn''t show anything at all and the device isn''t

Hello I am new in XEN and Linux. I am trying the VGA passthru. I can xen-pciback.hide EtherNet, Serial Com port. But when I xen-pciback.hide my VGA. I can no longer login to the Linux(Fedora 12). Then how can I xm create a XP DomU guest? Can anyone help? I am using Intel Q35 MB with Intel Core2 CPU. _______________________________________________ Xen-users mailing list

Hi, I''m on a HP DL365, amd64, running SLES10sp1, but with kernel and xen of SLES10sp2, therefore using Xen 3.2. The domU shall be a Windows HVM guest. I want use the Qlogic SAN card in a domU. I''m following these instructions: http://www.novell.com/communities/node/2880/assign-dedicated-network-card-or-pci-device-xen-virtual-machine well, there is written that this only

Hello, I FINALLY got Xen working with VT-d. I compiled Xen-unstable (3.3) from Mercurial on CentOS 5.2, but compiled my own kernel-xen from the latest CentOS SRPM. (Made sure pciback was built-in and not a module, as the stock kernel-xen has it as a module.) I''m probably going to write a how-to soon, so stay tuned! I have a JMicron SATA/PATA PCI Express controller with a DQ35JO

Hello, I FINALLY got Xen working with VT-d. I compiled Xen-unstable (3.3) from Mercurial on CentOS 5.2, but compiled my own kernel-xen from the latest CentOS SRPM. (Made sure pciback was built-in and not a module, as the stock kernel-xen has it as a module.) I''m probably going to write a how-to soon, so stay tuned! I have a JMicron SATA/PATA PCI Express controller with a DQ35JO

Hi all, I have a problem when from domU I need to configure a network interface. My system configuration is the next: dom0: xen 3.4.3 with 2.6.18-238.9.1.el5xen kernel, making pci back from a network card. All ok. This is the result from "lspci -v -s 09:00.0" 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) Subsystem: Broadcom

Hello all, I''m trying to pass my PCI device through to an HVM. I''m following the steps on the xen pci passthrough wiki. First I check my pci devices #lspci - 03:00.0 VGA compatible controller: ATI Technologies Inc Device 671d 03:00.1 Audio device: ATI Technologies Inc Device aa80 04:00.0 Display controller: ATI Technologies Inc Device 671d 04:00.1 Audio device: ATI

Hi all! I want to assign a physical network card (e100) to a domU: I think Dom0 is ok but domU does not recognize the pci nic. into DomU I don''t know wath should I see: I have nothing in dmesg nor in messages... Into Dom0 I have this modules.conf: options pciback hide=(0000:03: 08.0) install e100 /sbin/modprobe pciback; /sbin/modprobe --ignore-install e100 This is dmesg: pciback

Hi, I want to give direct access to my monitor for my linux domU so that my graphics can run smoothly inside domU which is Ubuntu 8.10 I tried doing the following, but things didn''t work out. 1. I boot my Xen on Debian ( lenny ) using kernel /boot/xen-3.2-1-i386.gz module /boot/vmlinuz-2.6.26-1-xen-686 root=/dev/sdc4 ro console=tty0 pciback.permissive pciback.hide=(00:02.0)

Hi everyone, First post, already a call for help :) I''m trying to use a gtx 580 with Xen 4 VGA Passthrough to test CUDA performances, the MB is an Asus P7P55 LX with a i7 870, VT-D is enabled in bios and reported as active by Xen. I''m using Debian Squeeze as Dom0 and DomU OS. Dom0 is configured with iommu=1 and iommu=verbose parameters and xen-pciback.hide=(01:00.0)(01:00.1)

Hi, I really need help. I spent 2 days already on this pci passthrough thing. I''m using Xen 3.2.1 with Centos 5.2 64 bits on intel VT. I''d like to use PCI passthrough and I don''t think I need VT-D functionality. I''m trying to pass PCI 12:01.0 to my domU guest. I got this error when I use "xm create /etc/xen/hvm_centos_2.cfg" Using config file

Hi @all, I have many domU on my server and they work fine, some of them have their own NICs with the PCI param in the config. Now I try to bring a soundcard for asterisk into a new domU and have the following trouble: rz3-ta:~ # lspci 00:00.0 Multimedia audio controller: Creative Labs SB Audigy (rev 04) PCI: Enabling device 0000:00:00.0 (0000 -> 0001) EMU10K1_Audigy: probe of 0000:00:00.0

Hi! i notice a serious regression with 3.5 as Dom0 kernel (3.4 was rock stable): 1st: only the GPU PCI Passthrough works, the PCI USB Controller is not recognized within the DomU (HVM Win7 64) Dom0 cmdline is: ro root=LABEL=dom0root xen-pciback.hide=(08:00.0)(08:00.1)(00:1d.0)(00:1d.1)(00:1d.2)(00:1d.7) security=apparmor noirqdebug nouveau.msi=1 Only 8:00.0 and 8:00.1 get passed through

Hi experts I use xen-4.0.0 and dom0 is 2.6.33 and domU is 2.6.34 #lspci ............... 01:00.0 Ethernet controller: Intel Corporation Unknown device 10a7 (rev 02) 01:00.1 Ethernet controller: Intel Corporation Unknown device 10a7 (rev 02) 05:00.0 Ethernet controller: Intel Corporation 82571EB Gigabit Ethernet Controller (rev 06) 05:00.1 Ethernet controller: Intel Corporation 82571EB Gigabit