similar to: Pci export configuration

Hello all, I''m trying to pass my PCI device through to an HVM. I''m following the steps on the xen pci passthrough wiki. First I check my pci devices #lspci - 03:00.0 VGA compatible controller: ATI Technologies Inc Device 671d 03:00.1 Audio device: ATI Technologies Inc Device aa80 04:00.0 Display controller: ATI Technologies Inc Device 671d 04:00.1 Audio device: ATI

Hello everybody, I''ve finished with pci export from DomU to Dom0 (Debian Etch) but now i have a new problem, and a big one. My ethernet card is dropping packets but after some time (i can''t tell how) It can work for a day (not in production so not hard tested) and then all packets are dropped. Look at the ifconfig output : eth0      Link encap:Ethernet  HWaddr

I just discovered that my xen hypervisor only believes that it has 3199 MB of memory, when there are 4GB inside the computer. I don''t know how long this has been this way, but I do not know how to try and force the hypervisor to realize how much memory it has. Any ideas how I can accomplish this? I am running CentOS 5 (RHEL 5), kernel 2.6.18-53.1.4.el5xen, x86_64, xen 3.0.3.

Hi, I''m on a HP DL365, amd64, running SLES10sp1, but with kernel and xen of SLES10sp2, therefore using Xen 3.2. The domU shall be a Windows HVM guest. I want use the Qlogic SAN card in a domU. I''m following these instructions: http://www.novell.com/communities/node/2880/assign-dedicated-network-card-or-pci-device-xen-virtual-machine well, there is written that this only

Hello, I´m trying to map one network interface of a Dual-Port e1000 Server Adapter to a DomU (firewall). In Dom0 the adaper is seen with lspci as: 06:00.0 Ethernet controller: Intel Corporation 631xESB/632xESB DPT LAN Controller Copper (rev 01) 06:00.1 Ethernet controller: Intel Corporation 631xESB/632xESB DPT LAN Controller Copper (rev 01) My goal is to map only 06:00.1 to DomU so I used this

Hello, I am desperately trying to get pci-passthrough to working. I want to pass a tg3 nic to domU. when booting domU I get a lot of messages: pcifront pci-0: pciback not responding!!! in domU, "ifconfig eth... adress up" hangs for 2 minutes, finally ifconfig -a shows a correct setting with no data transmitted rx/tx The IP Adress is being assigned, but there is no data transmission

Hi all! I want to assign a physical network card (e100) to a domU: I think Dom0 is ok but domU does not recognize the pci nic. into DomU I don''t know wath should I see: I have nothing in dmesg nor in messages... Into Dom0 I have this modules.conf: options pciback hide=(0000:03: 08.0) install e100 /sbin/modprobe pciback; /sbin/modprobe --ignore-install e100 This is dmesg: pciback

All, I would like to run the following issue past the list to confirm that my problem analysis makes sense or whether I missed something: We have a HP ML370G6 server with VT-x and VT-d enabled in the BIOS. It is equipped with two Smart Array HBAs - one connected to the HDD array (SmartArray P800) and one connected to an LTO tape drive (SmartArray P212). Both controllers use the same driver

So yesterday I got was able to get a domU successfully using a PCI SCSI card. This morning I restarted the host server. When I try to start up the same domU I get this error: Error: pci: improper device assignment specified: pci: 0000:0e:04.0 must be co-assigned to the same guest with 0000:0e:04.0, but it is not owned by pciback. How do I make this card owned by pciback on reboot. Do I need to

Hello everybody, for just one week I try to install three servers on an OpenSuSE 10.3 dom0 equipped with 4 NICs. One server is an OX using the onboard NIC via xenbr0. This server runs!! For my IPCop server I intended to use the three remaining NICs (Intel Pro100/S, 3Com 3C590, Realtek RTL-8139). These three NICs should be used natively by my IPCop. So I tried to use the pciback driver. I wrote a

Hi! As dom0 I''m running Ubuntu Hardy withe xen 3.3 from backports. Reason to using xen 3.3 is that I could get Intrepid stock kernel to work as domu with xen 3.2. Now the problem I have is that I can''t passthrough PCI-devices to my domu. If I run lspci in the domu nothing is returned. I''ve tried to use the kernel from Hardy (2.6.24-21-xen) and stock kernel from

Hello, I''m trying to add a USB dongle to my domU. I searched a lot and found an instruction (http://wiki.xen.org/xenwiki/XenUSBPassthrough.html). I added followings to domU''s cfg file: usb = 1 usbdevice = ''host:0925:1234'' But when i create my domU lsusb still doesn''t show anything at all and the device isn''t

Add commands to automatically prep devices for pass-through The current method for passing through devices requires users to either modify cryptic Linux boot parameters and reboot, or do a lot of manual reads and writes into sysfs nodes. This set of patches introduces commands to make this easier. It expands on the concept of "assignable" (from the list_assignable_devices command).

Thanks to the kind person(s) who worked on this. I am using PCI passthrough right now and it works. I hope support is added for VT domains too; That would be extremely useful. So far I have tried a NIC, USB, and PCI Video. The NIC works flawlessly. USB works as long as the devices are present at the time the domain is started. Hotplugging USB devices seems not to work. If I open

This issue was brought up about a year and a half ago. So I''ll bring it up again and see if anything happens. I''ve got an infiniband network and am attempting to pass the infiniband card through the host and give it to the guest. I''m working with standard CentOS 5.2 on both guest and host with their provided xen (3.0.3 ish). I''ve also attempted to install the

This issue was brought up about a year and a half ago. So I''ll bring it up again and see if anything happens. I''ve got an infiniband network and am attempting to pass the infiniband card through the host and give it to the guest. I''m working with standard CentOS 5.2 on both guest and host with their provided xen (3.0.3 ish). I''ve also attempted to install the

Hi @all, I have many domU on my server and they work fine, some of them have their own NICs with the PCI param in the config. Now I try to bring a soundcard for asterisk into a new domU and have the following trouble: rz3-ta:~ # lspci 00:00.0 Multimedia audio controller: Creative Labs SB Audigy (rev 04) PCI: Enabling device 0000:00:00.0 (0000 -> 0001) EMU10K1_Audigy: probe of 0000:00:00.0

Hello, I''m hoping someone may be able to push us in the right direction. I''m trying to get one of our products to work with the current branch of Xen (4.0/4.0.0) but I''m hitting a problem. We are currently using Xen 3.3.2 on a Sun Blade 600 chassis (with x6270 blades) this works great. But when we upgrade to Xen 4.0/4.0.1 we get the following message when

Hi, All the reviews for the AMD 890fx chipset reported that it supports IOMMU v1.2. But I cannot find any mention of that on AMD site. Does 890fx support IOMMU? Do 890fx motherboards with IOMMU exist? Does Xen support 890fx? Regards, Leonardo _______________________________________________ Xen-devel mailing list Xen-devel@lists.xensource.com http://lists.xensource.com/xen-devel

I''ve been trying to set up a VGA-passthrough on my Ubuntu 12.04 box to run Windows (for gaming) while leaving my RAID-5 array available (managed by Linux). First, here are the machine specs: CPU: AMD A8-3870K 3.4GHz Quad-Core APU GPU: APU-integrated AMD Radeon 6550 (shared memory) Mobo: ASUS F1A75-V EVO with AMD-virtualization enabled in UEFI-BIOS RAM: 8GB DDR3 1866 G-Skill Sniper