similar to: Xen unstable: Cannot ping gateway, ping dom0 to domU vice versa ok

Hi I got a FC4 system running as Host.  Within this I loaded Suse 10 as a guest OS, the config file is as below: kernel = "/boot/vmlinuz-2.6.11.12-xenU" memory = 100 name = "suseguest" nics = 1 vif= [''mac=aa:00:10:00:00:10, bridge=xen-br0''] ip = "192.168.2.2" disk = [''file:/dev/hdc3,hdc3,w''] root = "/dev/hdc3 rw" extra =

dummy0 Link encap:Ethernet HWaddr C6:C8:2A:04:FD:23 BROADCAST NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX

Greetings, I have two vms, one is a router and the other one is a client, for some reason, the client vm is unable get ip via dhcp from the router vm. here are outputs: vm1.xml: <interface type='bridge'> <mac address='52:54:00:54:78:be'/> <source bridge='virbr0'/> <model type='virtio'/> <address

Hi! I have a problem with my new Xen setup. I have installed Debian etch with netinstall and I''m using 2.6.18-6-xen-amd64 kernel in my dom0 and 3.0.3-0-4 version xen hypervisor. I''m using four network cards on my system and using three of them as xen bridges and dom0 is using the fourth one only for it''s own. So basicly both of my virtual servers use a network card

I am installed Xen 3.0 on a Fedora Core 4(2.6.12-1.1454_FC4xen0) machine. This machine is currently running one host domain: [root@]# xm list Name Id Mem(MB) CPU VCPU(s) State Time(s) Domain-0 0 128 0 1 r---- 49.1 fc4-vm1 1 63 0 1 -b--- 18.5 Following is the network configuration for Domain-0: eth0 Link

Well where do I start...I have a domU (ubuntu) booting and appears well but I don''t have an eth0 listed at all, dom) looks good. DomU: eth0 Link encap:Ethernet HWaddr 00:06:5B:15:C5:0B inet addr:10.99.99.5 Bcast:10.99.99.7 Mask:255.255.255.248 inet6 addr: fe80::206:5bff:fe15:c50b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

Hi all, I have a very strange situation, which I can''t explain. On a Core 2Quad server with 8GB RAM, we have 10 xen domU''s, as follows: vps.animalsaregreat.info login: root@zaxen01:[~]$ xm list Name ID Mem(MiB) VCPUs State Time(s) Domain-0 0 512 4 r----- 232.2 actionco.vm

Hi list. I started with Xen yesterday, but I am facing a bit of a problem. My system had always configure eth0 with 10.0.0.4/8 I am using Xen unstable source (on Debian sid) Now I installed Xen, rebooted the machine, and first the usual network is coming up and then the xend will be started. I''ll end up with this, but I am wondering if this should be the way of things to be

Hello, I am not able to see vrbr0 in my box. Can some one help me with this ? . I am trying KVM+libvirt and planing to use Routed mode. I hope this virbr0 must be up for using this . I can give an strace too. OS : Debian , kernel 3.12.0 libvrit version : 0.9.8 ____________________________________________________________________ root@:~# ifconfig br0 Link encap:Ethernet HWaddr

TEQL and Subnet problem I have a network topology shown below, and I am trying to use TEQL. My problem is: When I ping to P3.teql0 from P2 ("[P2]# ping 16.119.144.66"), the traffic can never go from P2.eth1, and all traffic only goes to P1.eth0. What P2.eth1 (16.119.144.33) did is broadcasting an ARP asking for the MAC address of 16.119.144.66, although I have specified the route to

Hello, I have problems with installation of my second DomU. I cannot ping it from the outside world and I cannot access outside world from this domain. I see it from Dom0 and my first DomU, same as my second DomU can ping Dom0 and my first DomU. I use xen 3.0.3 on ubuntu 6 LTS. DomU is running on debian. I also network-bridge script in the xend config.

Hi, I tried this post on the Xen list first with no answer. I have 4 machines and 3 of which (all different) have no network access when booted into Xen. I tried using Fedora Core 8 and it produced the same results. Is it normal for the virbr0 interface to take an arbitrary IP? How does it decide what to use? An ifconfig when booted into Xen shows the following: eth0 Link encap:Ethernet

On Friday 22 November 2013 04:19 PM, Sherin A wrote: > On Friday 22 November 2013 01:33 PM, Sherin A wrote: >> On Friday 22 November 2013 01:24 PM, Gao feng wrote: >>> On 11/22/2013 03:47 PM, Sherin A wrote: >>>> Hello, >>>> >>>> I am not able to see vrbr0 in my box. Can some one help me >>>> with this ? . I am trying

I am running Fedora 16 64bit and installed libvirt. I have the VM running with arm emulation with this one issue I can't figure out. I used Virtual Machine Manager to manage the VM and can access its console there. The Ethernet appears to be eth1 and the guest can set an IP on it etc. However, I cannot see any traffic from the Host when dumping any of the interfaces. I've tried

I'm having a wireless connection issue with an HP laptop and a Zotac media server after the 6.4 package updates from CR repository. Nothing changed with wireless config as far as I can tell. Both have been working fine with previous releases of 6.x. Oddly, if a cat 5 cable is connected for a few seconds and then disconnected the wireless works fine and survives a 'service network

I am posting the message below again because it did not go through last night. Help! Steve Timm -- ------------------------------------------------------------------ Steven C. Timm, Ph.D (630) 840-8525 timm@fnal.gov http://home.fnal.gov/~timm/ Fermilab Computing Division, Scientific Computing Facilities, Grid Facilities Department, FermiGrid Services Group, Assistant Group Leader.

I''ve looked everywhere for the error message I''ve posted in the title, doesn''t seem like anyone else has it (lots of missing hotplugs scripts). We''re using network-nat. ifconfig -a outputs this: eth0 Link encap:Ethernet HWaddr 00:19:99:a8:f4:5c inet addr:X.X.X.X Bcast:X.X.X.X Mask:255.255.255.255 inet6 addr: X::X:X:X:X/64 Scope:Link

Greetings! I finally got the install done for a couple of gust OSs (Win 2003 server & Suse Enterprise 10) Bothe gusts are up and running, but - no networking. My setup: Hardware - AMD Athlon 4200+, ABIT Motherboard, 4 GB of DDR2 RAM, 2 onboard GB NICs Host OS- Suse Linux Enterprise server 10 Xen - 3.0.2_09749-0.4 Config file for Win 2003 server guest: # -*- mode: python; -*-

Hi all, I just noticed that my two nics that are bonded via mode 0 are showing the same mac addy in ifconfig. Is this normal? In syslog I keep getting; kernel: pbond0: received packet with own address as source address Some guidance is appreciated before I dive in and troubleshoot. If I don't list the mac addy in my ifcfg-th# files, only one of the 2 nic comes up during boot.

Hello. I need your help, DomU xen network diconnects randomly, how do you monitoring this? When I connect to vnc server in the hosts, DomU is running, then I open the DomU, after that guest network responds. DomU Debian 6.03 over Centos 5.7 and Xen 3.03. My network configuration: eth0 Link encap:Ethernet HWaddr 68:B5:99:78:AA:6D inet addr:192.168.5.230 Bcast:192.168.5.255