similar to: IPMI Console: No luck once OS is booted

Hello, I have a server pfsense in bridge mode to function as transparent FW, the problem is that once I connect the pfsense between my router core and my core switch catalyst a few seconds begin to appear several messages like these: em2: watchdog timeout - resetting em2: watchdog timeout - resetting em2: watchdog timeout - resetting em2: watchdog timeout - resetting And the connection falls

Hi, I have Orinoco 802.11b PC Card from Proxim. I plugged it to pcmcia slot, but It doesn't work - no blinking LEDs, no wi0 in ifconfig. I have 7.1-PRERELEASE, laptop Prestigio Nobile 157. On NetBSD seems working, but NetBSD is not friendly with me. if_wi driver included in kernel. ----- dmesg Copyright (c) 1992-2008 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989,

Hello, My server is experiencing occasional kernel panics when under moderate load. I'm attaching a crash dump and the dmesg output. I'm not sure how to read the kernel backtrace but it looks like the Intel NIC (em0) caused the problem. Occasionally, I used to get a "em0: watchdog timeout -- resetting" error message, but I never had a kernel panic. The problem started last

Hi, I currently encounter spin lock 0xc0c83ba8 (sio) held by 0xc6337460 (tid 100005) too long panic: spin lock held too long cpuid=3 on hp server with two dual-core intel xeon (3.8GHz) and 3GB RAM. System is 7.1-PRELEASE last fetched 29.11.2008, 17:58 UTC. This happens with VSCom Card that was previously in use in a 5.3-STABLE system (also hp server, but older hardware) without problems. The

Hello Got strange problem with high system "%system load" and very slow user level programs (apache+php+mysql) behavior gstat shows 1.5-4% hard disk busy load but system shows about 20-30% load while user load is max 5%. vmstat shows from 2 to 35 process in "b" state. Now use 7.0-RELEASE-p5 , but the same problem was with 7.0-RELEASE. And have no idea what to do with this.

Hello, I am attempting to get by broadcom wifi card up and running, am sick of trying to get ndis working, and am attempting to use the bwi driver (originating in dragonflyBSD). I'm hoping others here have tried to do the same and have some pointers. I'm using 7.1-RELEASE (system/source are in-sync) and my card is a BCM94306MP. My dmesg is posted below. Bwi(4) is installed and it

I've just started using Dovecot, and can't seem to get the LDA to work. I get the following error: Mar 4 00:47:19 thebighonker dovecot: lda(ler): Error: user ler: Initialization failed: namespace configuration error: Duplicate namespace prefix: "" Mar 4 00:47:19 thebighonker dovecot: lda(ler): Fatal: Invalid user settings. Refer to server log for more information. Mar 4

Hello, I am trying to use a 1.5TB Eonstor raid array with FreeBSD 7.0, but I don't understand whether it is the raid or the scsi card or something else that is causing the computer problems when accessing the raid. My problem is that soon after recognizing the attached disk during boot, FreeBSD appears to hang for about 10 seconds and then says ahd0: Recovery Initiated - Card

Hi, I have a server (Dell PowerEdge SC1435, ServerWorks HT1000) on which I'd like to try installing FreeBSD. I've already failed to make 7.0 work on this box and was wondering if you have information about the behavior of the upcoming 7.1 on this hardware. I've been following the "HT1000 chipset errata saga" thread, and the commits by sos@ to CVS (around Jan 2008), but have

Good morning, I'm having a bit of an issue getting a 3CR990B-TXM NIC detected and usable. Just wondering if anyone knows of any issues with this NIC chipset and/or with the motherboard chipset. The motherboard is a Biostar GeForce 6100 AM2 using an nVidia nForce 410 chipset and nVidia GeForce 6100 vide chipset. I've tried FreeBSD 6.1, 6.2, 6-STABLE (from Wed), and 7-CURRENT (from

Hello all. I have a supermicro 16 bay box with a LSI 9211-8i card. We use it for temp data storage, and we wanted to try the l4z compression. After updating the source tree to r247839: and doing a make buildworld cycle all works fine. But at boot time we get some warnings. make_dev_physpath_alias: WARNING - Unable to alias gptid/281951f4-a996-11e1-83eb-00259061b51a to enc at

Hello everybody, we recently got three Dell PowerEdge servers equipped with Qlogic QLE2462 cards (dual FC 4Gbps ports) and an EMC CLARiiON CX3-40 SAN. The servers with the FC cards were successfully and extensively tested with an older SUN StorEdge T3 SAN. However, when we connect them to the CX3-40, create and mount a new partition and then do something as simple as "tar -C /san -xf

Hi, I've installed 7.2-PRERELEASE, csup on 20090423 at around 19:00 UTC. When I rebooted after installing world, X started (xdm in /etc/ttys) and immediately panicked the system, even before switching to the new VTY. I removed all ports and installed Xorg from today's ports HEAD, same result. This is the case with my old xorg.conf and a new one from 'Xorg -configure'. I

I have an Asus A8V-MX motherboard with an AMD Athlong 64 X2 3800+ CPU and I'm trying to run powerd to keep it cooler/quieter/greener. I'm running -STABLE (6.1-RC) cvsup'ed a couple of days ago, with a kernel config that consists of the SMP sample plus an atapicam device. I'm loading the cpufreq.ko module in /boot/loader.conf. I've attached my dmesg output and sysctl -a

Hi. On one of my fresh installed servers I am seeing the following output during boot: gptzfsboot: error 4 lba 30 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 30 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 31 gptzfsboot: error 4 lba 31 gptzfsboot:

I have a new system which includes a Plextor PX-740a DVD+-R/RW CD-R/RW drive attached to an Asus A8V-MX motherboard. When I try to use burncd to burn a cd, it writes all of the data, says "fixating CD, please wait.." and then reports burncd: ioctl(CDRIOCFIXATE): Input/output error Oddly enough, the CD seems to be usable. I can successfully burn the same file if I use cdrecord. The

Hi, I was trying to rebuild world on a FreeBSD 10 test system, that I had just installed. ZFS root was setup. I let the installation program do all the ZFS setup and configuration. I put root on a 5 disk encrypted raidz array. Besides the installer configuring 5 times the amount of swap space I asked for (asked for 8gb, installer put 8gb on each drive, for 40gb in total.) everything was working

Hi all, I have had this problem since day 1 on my new server. It has run since November 15th 2008, and serve approx. 10 GB worth of web traffic per month for the main site and then some 40 domains with mail and small web pages. (hence - it's NOT that busy yet) I started with 7.1-RELEASE-pX since I didn't have problems straight off - but it didn't last long. After a few days of

Here is what I did: # cd /root/nut/ # nut here it's checkouted repository # ./configure --with-user=_ups --with-group=_ups # cd drivers/ # make riello_ser # chgrp bin riello_ser # cp riello_ser /usr/local/bin # here I copied builder driver to folder where nut-package will store their files/drivers # pkg_add nut-2.6.5p1 # ls -la /dev/tty00 crw-rw---- 1 _ups _ups 8, 0 Jul 30

Hi all, A recent thread inspired me to try getting a proper serial console working on a Supermicro X9SCL motherboard with IPMI. However I find that while I see loader messages and the getty I enabled after boot I don't get any kernel messages which does somewhat limit the utility.. The BMC creates COM3 (/dev/cuau2) which works with getty. I modified /boot/loader.conf like so..