similar to: Re: Sweex UPS 500VA and NUT problem

Hi, I'm trying to get a sweex ups working with nut on debian sarge. This one: http://www.sweex.com/producten.php?lang=1&%20sectie=&item=59&artikel=95 It's shipped with UPSmart and according to the compatibility list it should work with the genericups upstype=7 driver. But it doesn't. I get: mybox:/etc/nut# /etc/init.d/nut start Starting Network UPS Tools: (upsdrvctl

Hi, FYI for all whom have the Sweex manageable UPS. I got my sweex manageable UPS500VA working with NetworkUPSTools using the ippon driver. Here is my the ups.conf file: [ups] driver = ippon port = /dev/cuad0 desc = "Server" Has anyone tried the ippon driver with Sweex 600VA, 700VA, and 800VA models? Regards, Jan

--- Arjen de Korte <nut+users at de-korte.org> wrote: > > > I also did: > > > > # ./megatec_usb -DDDDD -x vendor=06da -x mfr=OMRON > > /dev/usb/hiddev0 > > Please have a look at 'man 8 megatec_usb' again. > > You probably need to specify the '-x vendorid' and > '-x productid' options > and most likely, the

--- Arjen de Korte <nut+users at de-korte.org> wrote: > > > I also did: > > > > # ./megatec_usb -DDDDD -x vendor=06da -x mfr=OMRON > > /dev/usb/hiddev0 > > Please have a look at 'man 8 megatec_usb' again. > > You probably need to specify the '-x vendorid' and > '-x productid' options > and most likely, the

Hi Rok, I retired from working on NUT a few months ago, so I don't have the most up-to-date info. But the guys on the nut-upsdev mailing list (cc'd above) are very helpful. Both of your devices (or nearly identical ones) have been seen on the mailing lists before. The Sweex was first mentioned in a message by Eli Wapniarski on 14 Jun 2006 on nut-upsuser, and was most recently discussed

Hello, have some of you tried sweex UPS 1500VA (http://www.sweex.com/en/assortiment/power-security/power-protection/PP220). It is not listed in hardware compatibility list. As I can see, sweex can be problematic with drivers, but it is not possible to change this UPS to other model now. It is connected by USB and lsusb says only: Bus 002 Device 004: ID 0665:5161 Cypress Semiconductor USB to

Hello folks, I have a question regarding a sweex product. Its bundled with UPSmart v 2.12. I installed nut accordingly to the user manual included in the software. A quick check of data/drivers.list revealed to me i should use the: "Sweex" "500/1000" "contact closure - shipped with UPSmart" "genericups upstype=7" driver this driver

On Sep 6, 2019, at 3:43 PM, Martyn Hill wrote: > > Just thought to share my findings getting a Sweex PP200 650VA UPS working with NUT (I didn't see this particular model listed on the HCL.) Thanks! One of the other Sweex models shows a few instant commands: https://networkupstools.org/ddl/Sweex/INTELLIGENT_UPS_1500VA_P220.html Is anything listed when you run `upscmd -l ups`?

Dear Charles and team Just thought to share my findings getting a Sweex PP200 650VA UPS working with NUT (I didn't see this particular model listed on the HCL.) I picked-up one of these units quite cheaply at a Maplins store (before the chain closed-down) as a second UPS for my home/office - the first being an old Zigor Ebro650 - a long story for another post... NUT v2.7.4_7 is running

Arnaud Quette wrote: > Anyhow, I would more see this as a merge of all these drivers, with > some autodetection or flag/param to switch the mfr/model and maybe > capabilities... Whatever the driver name is, a good thing would be the > name of the protocol or something generic enough, though powermust is > fine. Ok, I made some minor changes to powermust, to make it less

Disclaimer: I've setup APC UPS monitoring and it works... ... but when it comes to mustek powermust 600usb (connected via com-port), I can't make it work. Got NUT installed via aptitude in ubuntu feisty and a basic setup, exactly the same as for the apc, except for the name of the ups and the corresponding section of ups.conf -- [mustek] driver = megatec port = /dev/ttyS1

Hi, I'm trying to figure out why my Sweex CA000022 is not detected by wcfxo on my SuSE Pro 9.3 running on a VIA EPIA SP motherboard. The card should work as its an Intel 82537EP based card. When Booting the IRQ assignments for the board indicate: Bus Dev Func Vendor Dev Class 0 20 0 8086 1080 0703 lspci shows: 0000:00:14.0 Modem: Intel Corporation: Unknown device 1080

Hello ! first off, thank you all for making this piece of software. from what i have seen so far this seems to be a really mature and advanced tool for all sorts of UPS models ! I`d like to tell that I own a UPS which isn`t listed on the compatibility list, but seems to be compatible. It is a PowerWalker - see this at

Hello ! first off, thank you all for making this piece of software. from what i have seen so far this seems to be a really mature and advanced tool for all sorts of UPS models ! I`d like to tell that I own a UPS which isn`t listed on the compatibility list, but seems to be compatible. It is a PowerWalker - see this at

Hi all, I just bought a Trust 1000VA PW-4105 UPS. I installed the UPS on FreeBSD 6.1, and installed NUT 2.0.3 via the FreeBSD port. I had no problems installing and configuring nut and the UPS to run with the PowerMust driver. My problem however is when I test the powerdown function by issuing the command: 'upsmon -c fsd' The UPS is cutting the power before the shutdown procedure

Hi all, I'm thinking buying a UPS Mustek PowerMust 600 USB to shutdown a Linux box on case of power failure. Can I use nut with this UPS without problems? I checked the page http://www.vamos-wentworth.org/upsinfo.html and was only something (incomplete) about Powermust 400 (information from November 2005). Could this be already changed? Thanks in advance.

Hi folks, has anyone been successful in getting a Mustek PowerMust 500 to talk to nut? All my attempts (tried "mustek" and "powermust" as drivers) have been unsuccessful so far. Thanks for any clues. Sascha -- http://yoyodyne.ath.cx

Hello, I'm working on getting nut using a Powermust Office 650 USB USV. Using today's trunk megatec_usb detects its vendorid 0665 productid 5161 but uses the agiler driver for it which apparently does not work (timeout...). I think this device is using that USB-to-serial chip but a different protocol behind. I got the phoenix subdriver working with the device but I had to extend

Hi, a few days ago, I bought some of those Mustek UPSes that have both a serial and a USB connector. Currently only the serial port is supported by the megatec driver. This works fine so far. Now I have seen there is a megatec_usb driver, which currently only supports 2 other UPSes. How can I help to find out whether the PowerMust might actually work with the megatec_usb driver? -- Regards,

Hello, first of all I'd like to thank all the NUT developers for their gorgeous work and for their efforts to make NUT the best and most complete UPS management software I've ever seen (seriously). Secondarily I'd like to help the NUT project as far as my help is needed, I'm not a programmer (by now...) but I would like to help somehow anyway. I have 3 UPS from the same