similar to: Sweex 1000VA UPS (was: powermust usb)

Hi, I'm having a hard time configuring a Mustek Powermust 600VA ups to work via USB with nut. I read somewhere that nut works OK via the rs232 cable, but unfortunately I don't have a COM port in my computer. The kernel detects the ups as an Xbox pad :) and loads the xpad module. I tried running /lib/nut/megatec with different /dev/ttySx but it displays megatec protocol UPS was not

On 1/23/07, Henning Brauer <hb-nut@bsws.de> wrote: > good new first: the megatec driverin 2.0.5 now works with the Online > Xanto S3000R here - well, for the very basics. > > the UPS has NO way ofidentifying itself. It also does not respond to > the power ratings query ("F"). I previously used a hacked up fentonups > driver. This means the driver cannot figure out

Hi all, i've read a thread about this UPS from Peter van Valderen. He tried to develop a driver for this specific type of UPS. I've downloaded nut-2.2.2 and tried to apply the patches (lakeview.patch & lakeview.v2.patch) but both resulted in rejected chunks. I've tried to ./configure with type lakeview and then a make, but the make command fails. Does anybody has any

First off, my apologies for bringing back this thread from the dead (September 2005, http://lists.alioth.debian.org/pipermail/nut-upsdev/2005-September/000150.html), however my problem seems relevant enough that I wondered what happened to this thread as it seems to have died after the message I quote below. Despite the fact that I am having trouble getting my Sweex 1000VA UPS (USB) to work, and

First off, my apologies for bringing back this thread from the dead (September 2005, http://lists.alioth.debian.org/pipermail/nut-upsdev/2005-September/000150.html), however my problem seems relevant enough that I wondered what happened to this thread as it seems to have died after the message I quote below. Despite the fact that I am having trouble getting my Sweex 1000VA UPS (USB) to work, and

Hello folks, I have a question regarding a sweex product. Its bundled with UPSmart v 2.12. I installed nut accordingly to the user manual included in the software. A quick check of data/drivers.list revealed to me i should use the: "Sweex" "500/1000" "contact closure - shipped with UPSmart" "genericups upstype=7" driver this driver

Hey all, thanks for your work on nut. I recently got myself a new cheap UPS, and have thus far determined very little about it. I can run whatever you like to help identify and work with it. So far I've played around with various settings and have had some limited success with the megatec_usb driver (Debian testing version): ----ups.conf---- [plexus] driver=megatec_usb model=500VA mfr=Plexus

Hi, I'm trying to get a sweex ups working with nut on debian sarge. This one: http://www.sweex.com/producten.php?lang=1&%20sectie=&item=59&artikel=95 It's shipped with UPSmart and according to the compatibility list it should work with the genericups upstype=7 driver. But it doesn't. I get: mybox:/etc/nut# /etc/init.d/nut start Starting Network UPS Tools: (upsdrvctl

Hi, fellow NUT gurus; I am having a big issue with our new Powercom Imperial Digital UPS. The UPS is come with a serial over USB port and plug into the usb port on the computer. I am having problem to setup our fedora 7 linux machine talks to the ups. The kernel 2.6.22.1 seems to be able to detect the ups is plug into one of its usb port. But it just couldn't establish a connection with

Hi, fellow NUT gurus; I am having a big issue with our new Powercom Imperial Digital UPS. The UPS is come with a serial over USB port and plug into the usb port on the computer. I am having problem to setup our fedora 7 linux machine talks to the ups. The kernel 2.6.22.1 seems to be able to detect the ups is plug into one of its usb port. But it just couldn't establish a connection with

On Thu, Dec 4, 2008 at 4:51 PM, Arjen de Korte <adkorte-guest at alioth.debian.org> wrote: > Author: adkorte-guest > Date: Thu Dec 4 21:51:28 2008 > New Revision: 1596 > > Log: > Added new richcomm_usb driver based on the lakeview_usb driver (using libusb). Sorry if I wasn't clear - I was advocating *renaming* the lakeview_usb driver to richcomm_usb. Is there another

Hi Rok, I retired from working on NUT a few months ago, so I don't have the most up-to-date info. But the guys on the nut-upsdev mailing list (cc'd above) are very helpful. Both of your devices (or nearly identical ones) have been seen on the mailing lists before. The Sweex was first mentioned in a message by Eli Wapniarski on 14 Jun 2006 on nut-upsuser, and was most recently discussed

sent two 0 byte packets to the driver, then it sent 'URB_FUNCTION_SYNC_REST_PIPE_AND_CLEAR_STALL' down the pipe which seems to come back up as well, and then the UPS turned off. I'll play around later with what happens in that regard, although it may be a bit tricky to figure out when the battery is low without having it plugged in ;-) Also, about nut-usbups.rules.in... The

sent two 0 byte packets to the driver, then it sent 'URB_FUNCTION_SYNC_REST_PIPE_AND_CLEAR_STALL' down the pipe which seems to come back up as well, and then the UPS turned off. I'll play around later with what happens in that regard, although it may be a bit tricky to figure out when the battery is low without having it plugged in ;-) Also, about nut-usbups.rules.in... The

sent two 0 byte packets to the driver, then it sent 'URB_FUNCTION_SYNC_REST_PIPE_AND_CLEAR_STALL' down the pipe which seems to come back up as well, and then the UPS turned off. I'll play around later with what happens in that regard, although it may be a bit tricky to figure out when the battery is low without having it plugged in ;-) Also, about nut-usbups.rules.in... The

Hello, have some of you tried sweex UPS 1500VA (http://www.sweex.com/en/assortiment/power-security/power-protection/PP220). It is not listed in hardware compatibility list. As I can see, sweex can be problematic with drivers, but it is not possible to change this UPS to other model now. It is connected by USB and lsusb says only: Bus 002 Device 004: ID 0665:5161 Cypress Semiconductor USB to

Hi, FYI for all whom have the Sweex manageable UPS. I got my sweex manageable UPS500VA working with NetworkUPSTools using the ippon driver. Here is my the ups.conf file: [ups] driver = ippon port = /dev/cuad0 desc = "Server" Has anyone tried the ippon driver with Sweex 600VA, 700VA, and 800VA models? Regards, Jan

On Sep 6, 2019, at 3:43 PM, Martyn Hill wrote: > > Just thought to share my findings getting a Sweex PP200 650VA UPS working with NUT (I didn't see this particular model listed on the HCL.) Thanks! One of the other Sweex models shows a few instant commands: https://networkupstools.org/ddl/Sweex/INTELLIGENT_UPS_1500VA_P220.html Is anything listed when you run `upscmd -l ups`?

Arjan, I am forwarding your email to the nut-upsuser mailing list. I am not an expert on the Powermust driver; hopefully somebody on the mailing list will be able to help you! -- Peter Arjan DJ wrote: > > Dear Peter, > Some days ago I bought a Sweex UPS (500VA) and now I have set up NUT (using > the Powermust driver) and everything is working fine. Invoking upsmon -c fsd > gives

Hi, I'm trying to figure out why my Sweex CA000022 is not detected by wcfxo on my SuSE Pro 9.3 running on a VIA EPIA SP motherboard. The card should work as its an Intel 82537EP based card. When Booting the IRQ assignments for the board indicate: Bus Dev Func Vendor Dev Class 0 20 0 8086 1080 0703 lspci shows: 0000:00:14.0 Modem: Intel Corporation: Unknown device 1080