similar to: centos5 r8169

Hi all. I have two servers 2.6.18-308.4.1.el5PAE CentOS release 5.7 (Final) Both have two external gigabit network cards (installed Planet with Realtek r8169 chipset). lspci 04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10) 04:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10) /var/log/messages May 3

Hi all, Another FYI-mail (and just to verify that I'm not going insane here); I recently purchased an ASUS M3A78-EMH HDMI -board with a tri-core Phenom. This is a small uATX-board with all the garnish integrated motherboards are supposed to come with, and fairly well supported in CentOS 5 and other modern distros. When I installed it (~2 months ago) the NIC was not supported; Ethernet

Hi, anybody know how to fix this. May 20 12:16:15 wolfpac kernel: NETDEV WATCHDOG: eth0 (r8169): transmit queue 0 timed out May 20 12:16:15 wolfpac kernel: Modules linked in: pf_ring(U) af_key iptable_nat ipt_LOG iptable_filter ip_tables nf_conntrack_ipv6 nf_defrag_ipv6 xt_state ip6t_LOG xt_limit ip6table_filter ip6_tables bridge stp llc nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4

Bill, your CentOS 5 RTL8110 page should probably be updated. I've confirmed that there's a newer r8169 driver in the kernel that works with the RTL8110. RealTek's web site now carries the new r8169 instead of the r1000. The newer driver fixed a problem I was having on one host so we should probably recommend it over the older r1000. I've updated my CentOS 4 page. Kirk Bocek

Hi all, I've recently upgraded a system from CentOS 4.4 to CentOS5, and now when the system boots, the r8169 ethernet card doesn't come up. After the boot sequence, if I type "ifup eth1 | ifup eth1.10 | ifup eth1.203" then the adapter starts up ok. It seems to be something with the boot sequence it loads the ethernet adapters a different way around (ie 4.4 eth0 is now

Hi all, Our intranet's WAN interface just stopped working yesterday, and I can't figure it out. The machine has a Gigabyte motherboard, with on-board RTL-8110SC/8169SC Gigabit Ethernet and D-Link PCI NIC for the LAN side. I can get into the LAN side without an issue, but can't see the WAN side at all. [root at intranet ~]# ifconfig eth0 up eth0: unknown interface: No such device

On 07/26/2016 02:58 PM, geo wrote: > > hello Ned. > > On 07/26/2016 02:04 PM, Ned Slider wrote: >> On 26/07/16 19:04, geo.inbox.ignored wrote: > <<>> > >>> ]$ lspci|grep Realtek >>> 0e:00.0 Network controller: Realtek Semiconductor Co., Ltd. \ >>> RTL8187SE Wireless LAN Controller (rev 22) >>> 14:00.0 Ethernet

hello Ned. On 07/26/2016 02:04 PM, Ned Slider wrote: > On 26/07/16 19:04, geo.inbox.ignored wrote: <<>> >> ]$ lspci|grep Realtek >> 0e:00.0 Network controller: Realtek Semiconductor Co., Ltd. \ >> RTL8187SE Wireless LAN Controller (rev 22) >> 14:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. \ >> RTL8101/2/6E PCI Express

I am having an issue where eth1 is throwing some messages and stops responding. Restarting networking doesn't work and also just bringing down eth1 with 'ifdown' doesn't fix it. I have never seen anything like these messages: eth1: no IPv6 routers present r8169 0000:03:00.0: eth1: rtl_counters_cond == 1 (loop: 1000, delay: 10). r8169 0000:03:00.0: eth1: rtl_chipcmd_cond == 1

I am having an issue where eth1 is throwing some messages and stops responding. Restarting networking doesn't work and also just bringing down eth1 with 'ifdown' doesn't fix it. I have never seen anything like these messages: eth1: no IPv6 routers present r8169 0000:03:00.0: eth1: rtl_counters_cond == 1 (loop: 1000, delay: 10). r8169 0000:03:00.0: eth1: rtl_chipcmd_cond == 1

Dear All, I have an onboard Realtek RTL8111/8168B NIC. from lspci -vv : 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) It is detected, but why the speed is always 100Mbps, already change cable but still no luck. I use ethtool and from the output it seems that system know that this NIC support gigabit speed : ???????

Hi guys; I'm having a problem with a new pc that has an Realtec ethernet device. Don't know why the driver is not loading and is not detected during installation process. I tried to load r8169.ko unsuccessfully. It load but no device is detected. No dmesg or /var/log/message. ?Any help on how I can configure correctly this ethernet device? This are the data that I have: # lspci

On 26/07/16 19:04, geo.inbox.ignored wrote: > > greetings one and all. > > installing centos 7 32 bit i386 to laptop; > > specs: > > toshiba satellite l455d-s5976 > amd sempron si-42 > 2 GB ddr2 > 250 GB hdd > > ]$ lspci|grep Realtek > 0e:00.0 Network controller: Realtek Semiconductor Co., Ltd. \ > RTL8187SE Wireless LAN Controller (rev 22) >

On 29/03/2020 14:31, Patrick DERWAEL wrote: > Hi Phil > > Here it is: > > > [root at totorbex ~]# lspci -nn > .00:00.0 Host bridge [0600]: Intel Corporation Atom/Celeron/Pentium > Processor x5-E8000/J3xxx/N3xxx Series SoC Transaction Register [8086:2280] > (rev 21) > 00:02.0 VGA compatible controller [0300]: Intel Corporation > Atom/Celeron/Pentium Processor

I''m trying to build out a test cloud using XCP 1.0.0 beta with 3 machines of 18 cores total (Phenom II 1090s). I''ve built three machines, installed XCP 1.0.0 beta on them and they all three have the same problem - the Realtek network cards don''t work. The following is the output from lspci 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI

Hello, We can see # lspci 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) I have used a custom kernel to start with centos 5.1 as an initial installation Our customer on this kernel has experienced slow pref on samba shares (50 seconds to open a file) So I have decided to updrade to centos 5.2 that have the right

greetings one and all. installing centos 7 32 bit i386 to laptop; specs: toshiba satellite l455d-s5976 amd sempron si-42 2 GB ddr2 250 GB hdd ]$ lspci|grep Realtek 0e:00.0 Network controller: Realtek Semiconductor Co., Ltd. \ RTL8187SE Wireless LAN Controller (rev 22) 14:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. \ RTL8101/2/6E PCI Express Fast/Gigabit Ethernet

Hello, I have an issue with my XEN system. I suspect that it might be a bug, but I''m no linux expert, so I don''t know. Here is my problem: I have an ASUS P7P55D-E Premium motherboard, and a Western Digital Caviar Black SATA-III 1TB hdd. I am trying to use AHCI. The dom0 is an Arch Linux. The dom0 boots fine until Intel VT-d is enabled in the BIOS. When I enable it Arch

I have a strange problem on one machine where eth0 gets killed when I add a virtual interface. It's got something to do with the NIC ordering or with the xen network script having a problem with multiple NICs and virtual interfaces. I could need some help/comments on this. Some history: I added a NIC (chip identifies as Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit

Hi : I am trying to do PCIe passthrough on HVM domu. I have window XP as a HVM domu and xen-4.0. dom0 and domU (without device assign) works fine. I have more than one NIC card. I want to passthrough 03:00.0 to domu here are the list of my nic cards: lspci | grep -i eth 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)