similar to: Change RX Signalling Bits in Dahdi drivers

Does anyone know if asterisk supports PLAR (Private Line Auto Ringdown). The Oreilly (Asterisk: Future of Telephony) book mentions it in passing saying that all you need to enable it is to set immediate=yes in zapata.conf. Has anyone implemented this in brokerage trading environments? Thanks in advance. -------------- next part -------------- An HTML attachment was scrubbed... URL:

You have the session target as the IP address of the router's own ethernet interface. You probably want that to be the address of the Asterisk server instead. I also highly recommend you use full duplex ethernet, as voice packets don't really like to be restransmitted when a collision happens. -d > Message: 10 > From: "Bartosz Jozwiak" <bartek@cq-link.sr> >

Hi, Im new, but trying real hard! I just need general direction, not details yet..i'll try to figure those...just looking to avoid brick walls...bottlenecks...inefficiencies etc upfront. Hardware: motorola vt2442 - trixbox Apps: Dot Net application that operates the Manager API and the FASTAGI interfaces. I have the 2442 set as a PLAR so as soon as the ext is off-hook, it dials into the *61

Hello, Could somebody tell me if I can connect CISCO 2600 router with support of H.323 to Asterisk ? If it is possible could somebody tell me how to do it. I would like to document it and put on some website so everyone can see it. Regards, -- bart -------------- next part -------------- An HTML attachment was scrubbed... URL:

say I needed to send a broadcast message that I wanted every user to hear when the pick up thier phone? can I "Play,message" on a line just before they get dialtone? or maybe after they dial before ring? how about a "ringdown" to a voicemail box and on end return them to thier line for the dialout? can * do ringdowns? when a user picks up an extension it automagically

Basically, I am looking to set up an extension which will be used as a "help-line". I want it to function kind of like the bat phone from the old Batman series, where Commissioner Gordon would pick up the extension in his office and it would ring the phone back at Wayne's mansion. Is there a way to duplicate this functionality with Asterisk? I just need asterisk to auto-dial an

I would think I could do this but for some reason I am stymied. I have a PRI from RCN connected to a cisco 3640 (in my day "cisco" is all lower case :-)). My config looks something like this on the cisco... --------------------------------------------------------- voice-card 3 dsp services dspfarm ! ip cef ! isdn switch-type primary-5ess ! controller T1 3/0 framing esf linecode

Hello, everyone. Right now, we are trying launch our own PBX system based on Asterisk(Fedora) with Cisco 2611. Cisco has 2 port FXO card installed on it. For testing, I have 2611 hooked into phone line with number of xxx-xxx-xxxx fine. (I'll call it F). Using softphone, I can dial in extension 1001 on asterisk, which should talk to cisco. After initial connection to Asterisk, I have try to

Hi all, I have looked through the wiki for any information on how to make an extension autodial another extension when it goes off hook. Anyone done this or know how it's done. regards Dave

I have cisco phones running SCCP, and a cisco 2600 with FXO I'm using for PSTN access. I can dial out, but inbound calls are not ringing a phone. Please see my config In the 2600 I'm PLAR'ing the line and I have a SIP Dial-Peer for 4001 voice-port 1/1/0 output attenuation 0 echo-cancel coverage 32 no comfort-noise timing hookflash-out 50 connection plar opx 4001

OK, here's a configuration challenge: I want to have certain line appearances able to be "interrupted" by various other line apperances elsewhere in the office. This is harder to describe than it is to demonstrate, so I'll do that: Let's assume I have Cisco 7960's on all desks. 1) Call comes from inbound line X destined on extension 1234 2) Phones A, B, C all

I'm having great success using Cisco 7960s with Asterisk but one Cisco 7960 specific function that's puzzling me is programming the 'line buttons' (6 buttons on the upper right side of the phone) for speed dial. I'm not using any Cisco applications like Call Manager and the phones are SIP. *All* of the documentation I've found over the last several days continues to refer

Hey all, I'm pretty new to Asterisk and VoIP in general, so I'm hoping I can get a bit of help here. First I'll explain my setup, and then my problem. Right now I have a Cisco 3640 with a VIC2FXO card in it which has 2 FXO ports. I have an analog phone line plugged into the first port (voice-port 1/0/0). I've got it setup so that calls coming into that analog line are