similar to: Can not get my Eicon Diva running with Asterisk...

Hello *, I have an All-In-One intranet server <samba3> and usualy a seperated <router> as default gateway, which connect me using HSPA to the internet Now I have installed an Huawai K3765 on my <samba3>, installed "pppd" + usb-modeswitch and removed the default gateway to <router>. OK I can continue surfing trough the <router> and <samba3> is

Hello, since I had delayed the programming of the UPS Device part, now it is time to continue... My Device is "24 V DC modular ATX PSU" which replace the standard ATX Power Supply in PCs and use 15-43 V Input Voltage. The microcontroller is a TI LM3S5T36 Cortex M3 and I get the "UPS" infos using up to 4 Maxim DS1780 and some I?C current sensors. The ATX PSU has 4

Hello, I am looking for ideas and suggestions. I want to use a 16 port GSM gateway as a trunk for outbound/inbound. I will also have two PSTN phone lines coming into the Asterisk server. All calls will go to an IVR on the Asterisk PBX. Outbound from extensions will route to GSM-GW when the dialed number matches a pattern set in the GSM-GW trunk. And accordingly for the PSTN trunks. But that's

(CC-ing to mailinglist that is about syslinux and extlinux) On Thu, May 11, 2006 at 02:24:33PM +0200, Michelle Konzack wrote: > Am 2006-05-09 15:22:29, schrieb martin f krafft: > > also sprach Michelle Konzack <linux4michelle at freenet.de> [2006.05.07.1442 +0200]: > > > 2) mkdosfs -F 16 /dev/sda1 > > > 3) syslinux /dev/sda1 > >

Hello, Since I have now nearly all stuff running on my LH7A404 and now I am working on my DS80C411, I like to know, whether NUT show the APC UPS stats like the APC tools. Currently I do not know, HOW NUT triber the USB-Poert to get out the infos of the UPS. In theory I do send out only arround 5-60 lines of data which then NUT or any other programs must parse or something

Hello *, I have my "24V DC modular ATX PSU" running yet and it collect already the data form the DS1780 and MAX1036/8. The Microcontroller is a Maxim Integrated Device DS89C450 and the USB-Controller a MAX3420E which works over SPI Bit-Banging. OK, this is now working and enumeration is done... ;-) Now since the PSU is a "Function" I was looking into the Linux

Hello Charles, Am 2008-03-13 19:27:27, schrieb Charles Lepple: > Another advantage of going the HID PDC route (regardless of whether > NUT is involved) is that the device is essentially self-describing. If > the first version does not have a shutdown flag, but later versions > do, then very little driver code needs to change - just device > firmware. > > Also, I believe that

Sorry for posting again, but because the subject.Hi All, I have 5 servers each: Intel Quad Core i7 2.4Gig (8 processors)2 *1TB HDD2*1Gig NIC12G RAM I installed XCP 0.5 on each and all are joining a resource pool.Then I installed 2 Centos 5.5 VM on each XCP host and I used the following command to specify the number of vCPUs for each VM: xe vm-param-set uuid=$VM_UUID VCPUs-max=4xe vm-param-set

Hello, is it possible to use a eicon diva server 2M as FXO ? Regards Andreas Moroder

Does anyone have this card working with Asterisk? Thanks

Hi. I've been trying out Asterisk and it looks good. I've have got the VoiP stuff working with some softphones and I'm very impressed. My next step was to interface it with my phone system here to try it out that way. I have an Eicon Diva PCI 2.02 (not server) lying around which I have put into my asterisk box and I've tried to configure it but I've had no luck so far.

Hi, just a quickie... We've bought one of these primarily for Hylafax use, but since this card can run in NT mode, I'd be curious to use one of the four ports on it to 'serve' our PBX as a trunk for tests and playing with Asterisk. My question is, "Is it likely that we can use 3 ports with Hylafax in normal ISDN client mode, and the remaining port in NT mode with

Hello, I'm thinking of deploying Asterisk. I already have a handful of EICON Diva 2.01 PCI ISDN cards. I was thinking if it's possible to insert 4 such cards to my PC-Asterisk server (which I yet have to install) and use them as 4 lines in case anyone has to call me in / I have to call out using ISDN line(s)? Any reply appreciated. Tomek

Hi all, I have trouble getting my setup configured properly. I have a Eicon|DIVA Server BRI-2M/-2F card installed, using melware driver and following asterisk wiki guidelines. However whe I try to dialup the number I get only silence and after a while disconnection. The following is displayed on the console. What am I doing wrong ? *CLI> == Starting CAPI[contr1/0991]/0 at demo,0991,1

That was my impression as well, I tried adding switchtype=qsig in zapata.conf, but all I see is the capi information... No connection... Janne > -----Ursprungligt meddelande----- > Fr?n: asterisk-users-bounces@lists.digium.com > [mailto:asterisk-users-bounces@lists.digium.com] F?r Peter Svensson > Skickat: den 23 februari 2005 21:34 > Till: Asterisk Users Mailing List -

I just wanted to let you know that it's possible to use Eicon DIVA PCI 2.01 ISDN cards (not "server" divas) with asterisk. First thing to do is to load the module. If you have two of these cards, you should do it like that: modprobe -v hisax protocol=2,2 type=11,11 And now you can have up to 4 incoming calls with two cards (try calling yourself and see if anything gets into

Hey, If anyone supplies or knows where I can get either an Eicon Diva V-4BRI or a Junghanns QuadBRI card in Australia, please could you contact me offlist? Also, if anyone has any second-hand ones they need to get rid of, I'd be interested in making an offer! I've been checking eBay, but there don't seem to be any of these available at the moment. Thanks, Avi -- National Manager -

Dear all, I'm planning to buying Eicon Diva Server V-BRI for my asterisk server and run with chan_capi. Is anybody using that card ? Would appreciate any feedback. Bartosz

Hi! I'm trying to enable echo cancelation with my Eicon Diva Server 4 Bri card. I've enabled it from zapata.conf, (as I read from www.voip-info.org) ------------------------------- ; Enable echo cancellation echocancel=64 echocancelwhenbridged=yes echotraining=2000 ---------------------------- but nothing seems to change, echo is still present. Any idea? Should I enable/change something

Hey guys This is probably for Armin, but I thought maybe someone else might have something I could try. I'm having a problem with one of my Eicon Diva V-4BRI cards and I'm trying to work out if its a driver configuration error, card failure or telco problem: I have an Asterisk box running -- the Eicon drivers see all four ports on my card, capi.conf is configured with all four ports