similar to: TDM410 PTSN line setup with 1 analog phone

Hi recently bought a soekris net5501 and a tdm410 to place in there. I am having some issues attaching 12V power to the card via the molex card - basically the box for the motherboard is too small. I have read up about a PWR2400b and it seems to use 2wire pin, I am guessing to connect to P8 just behind the molex connector on the tdm410. can any one here confirm this, or have any info on the

I'm looking into getting a new phone and wondering what the difference in functionality is between a single line phone with call waiting and a real 2 line phone (either a real SIP phone or an analog 2 line phone and a 2 port ATA) is. Why would I want the real 2 lines vs. just being able to take an incoming call via call-waiting? Cheers, b. -------------- next part -------------- A non-text

I am facing one way audio problem in sip trunking between asterisk and avaya. +-------------+ +----+ | avaya sip |-------| P1 | +-------------+ +----+ | | | +-------------+ | Asterisk | WAN

I beg to differ. Digium is hiding from the real world and somebody is going take the software and run with it. My customers lost in excess of $50.000 and cut my pay in half, because of hackers. The hackers figured out how to scan every asterisk for weak passwords or open ports, and bang them real good. We need two things: a) disable in sip.conf the reply for INVITES that have wrong user

Hello everyone.... Searching the archives and google always comes up with entries regarding the "dyn" dns option in the 7960, but I can't find answers to my specific question.... My 7960 is connected via cable modem and is NAT'ed (everything is working fine). On the 7960 under SIP configuration\NAT Address I have the public IP of my cable connection. Comcast gives me a

I am putting together my first *. I had it running with two other pc's running xlite and setup voicemail and a couple of menus and submenus and had that running well. I had order a couple of oem x100p cards from digitnetworks. I installed them as they said with their voicepet2.2.zip drivers and did the modprobe on zaptel and wcfxo and then ran ztcfg -vv and got this: Zaptel Configuration

I just spent the last hour or so trying to get this firmware to work across a NAT with no success. I have a GS BT101 working through the same NAT, so I don't think it's the NAT itself. I have a STUN setup in * and pointed the UIP200 to it and I tryed several combinations of nat= in the sip.conf and in the config files for this phone. No luck(yes, I did a reload now with each change in

I am not that good at regex and it's use in Asterisk. I am running Asterisk 1.4.13 Currently I have this in my extensions.conf for incoming calls on our house phone line: [housemenu] exten => s,1,GotoIF($["${CALLERID(num)}" = "815xxxxxxx"]?s|12); 815xxxxxxx is our home phone number, when caller id fails or is missing that is what is recorded. I want to expand this

I am trying to get distinctive ringing going again with these phones, depending on the outside line the call comes in on. I had a working 1.0.x Asterisk setup using: SetVar(ALERT_INFO=<http://127.0.0.1/Bellcore-dr2>) Which used the short quick rings. In Asterisk 1.4, I have tried several things, but I think the correct syntax is: Set(_ALERT_INFO=<http://127.0.0.1/Bellcore-dr2>) But

My PSTN line doesn't allways hang up properly after it goes to voicemail. The problem occurs when a caller hangs up during the initial greeting. Even though the hangup accured, voicemail continues to record, usually a fast busy and/or a teleco generated "please hangup now" message. After the voicemail.conf 'maxmessage=180' expires the line simply stays offhook. The hardware

I had a working system using * 1.0 and then 1.2 and now Asterisk 1.4.13 with addons 1.4.4, zaptel 1.4.6, libpri 1.4.2. I have a mix of Grandstream (GXP2000), Uniden uip-200, Linksys Wireless G, and analog phones via Adtran chan bank. When I went to * 1.4.13, the Uniden phones stopped being able to login to voicemail. All phones are on same lan with Asterisk. I get 'Login incorrect'

Hello, If my understanding is correct, these days it seems that many ISDN BRI lines are configured in energy saving mode in which signalling D-channel is "dropped" until a new call comes in. Is it possible to replicate this behaviour with Asterisk (when Asterisk is in NT mode and is seen as a public ISDN by another PBX, for instance) ? If not, would you it would be a useful addition to

Hi I have come across a problem, with my tdp410 and soekris board (basically pc on a chip amd geode cpu). I am using the box as a firewall/asterisk box. The problem occurs when I drop ppp and I get dead loop dectiotn going, I seem to lose interrupts and get lots of messages in syslog from wctdm24xx saying missed interrupt increasing latency its out lined here

Hi all, Recently I have instaled one Digium TDM410 on my Asterisk. After instaled , I can do outgoing calls but I cant receive calls. I receive the following messages: chan_dahdi.c: Got event 2 (Ring/Answered)...[Sep 14 11:24:44] NOTICE[2654] chan_dahdi.c: Got event 18 (Ring Begin)...[Sep 14 11:24:44] WARNING[2654] pbx.c: Channel 'DAHDI/4-1' sent into invalid extension 's' in

Hello, Trying to set up res_fax_spandsp. Based on https://wiki.asterisk.org/wiki/display/AST/T.38+Fax+Gateway I wrote this in my extensions.conf: exten => 306,1,NoOp(Fax transmission) same => n,Set(FAXOPT(gateway)=yes) same => n,Dial(DAHDI/3) ----->FXS port to fax machine same => n,Hangup() Call flow Im trying to pull out is as follows: Zoiper -->

I am setting up my * for at home office and still have analog phones attached and answer from those analog phones and not necessarily through the pbx. I found that with the X100P cards, they see the 2nd ring and will be ready to answer the line. I used a Wait to pause and allow another 2 rings before * answers. But found that if we answer the line after the 2nd ring and before the 4th, * still

I got a Uniden UIP200 and started to configure it and I am lost.... I have a tftp server setup on my * server and have the files unidencom.txt and uniden<mac>.txt there. But it doesn't quite work yet. It registers as a sip phone (sip show peers), but I cann't dial it and the display shows #1 disconnected all the time. It has firmware version BS4.59a in it. I have no idea if I

Hello Asterisk List, My company is running a bunch of Asterisk servers behind a Kamailio (openSER) SIP proxy gateway. Calls come in from our PTSN to VOIP service to Kamailio, which then randomly chooses an Asterisk server to handle the call. All Asterisk servers are 1.6.0.9, but the issue I'm about to describe exists in 1.6.1.5-rc1 as well. Ultimately what I want to do is cap each

Hi I am having some problem forcing my tdm410 to alaw over ulaw, I have 1.6.1.0 asterisk (debian i486) dahdi 1:2.2.0 built with the hardware echo canceller firmware /etc/asterisk/chan_dahdi.conf alaw=1-4 but I have this in the general section, before any channel definition dahdi show channel 1 Default law: ulaw even when i have a call going it is still ulaw Thanks Alex

I'm running * 1.4 and can successfully restart asterisk from the command line with: /usr/sbin/asterisk -r -x "restart gracefully" However, I have a cron job that tries to restart asterisk and gets this error: No such command 'restart gracefully' (type 'help restart gracefully' for other possible commands) Can anyone think of why this is happening? Thanks