similar to: After a long break, one more try at bond/bridge nics

Hi all, Read many posts on the subject. Using 802.3ad. Few problems; Cannot ping some hosts on the network, they are all up. Cannot resolve via DNS which is one of the hosts that I cannot ping, internal nor external DNS hosts. Unplugging the NICS and plugging them back in will then not allow pining if the default d=gateway. When cold booting it somewhat works, some hosts are pingable while

Hi all, I just noticed that my two nics that are bonded via mode 0 are showing the same mac addy in ifconfig. Is this normal? In syslog I keep getting; kernel: pbond0: received packet with own address as source address Some guidance is appreciated before I dive in and troubleshoot. If I don't list the mac addy in my ifcfg-th# files, only one of the 2 nic comes up during boot.

Hi all, I've setup a ethernet bond on my centos 5.6 server , when i do a reboot the bond does come up but cleared all the slaves and i've to manually re-add them with ifenslave. does anyone know a solution to this? am i missing something? offcourse i can add it to my rc.local but there must be a more elegant way. please see my configs below Thanks, Wessel ifcfg-bond0: DEVICE=bond0

Hi all, we are testing CentOS 7 in order to migrate from Scientific Linux 6 / CentOS 6 and we are facing an issue with the network. Trying to configure network with teaming in activebackup mode or also with bonding in mode=1 (active backup as well) we see many RX dropped packets in the bond0 interface (around 10% of the total), 100% RX drops in the backup interface and 0% in the active interface.

Dear All, Please ignore my previous mail I have using CentOS 4.4 Linux and Kernel Version is 2.6.9-42.EL I have configured Cluster Suite with 2 servers Server 1 : 192.168.13.110 IP Address and hostname is primary Server 2 : 192.168.13.179 IP Address and hostname is secondary Floating : 192.168.13.83 IP Address (Assumed by currently active server) I have configured Ethernet Channel Bonding in

I'm running into a situation where a bogus bonded interface named "bond0" is being created, in addition to the desired "bond2" interface. Can anyone confirm this? Anyone know why it's happening or what I do to get rid of it? I wanted to start my numbering scheme at 2 instead of 0, which I didn't think would be a problem. As you can see, I have no reference

Hi, I'm trying to configure a network bridge over a bonding without any success. Here is my configuration: ifcfg-eth0: DEVICE=eth0 HWADDR=00:1E:C9:E8:3F:E5 ONBOOT=yes USERCTL=no MASTER=bond0 SLAVE=yes ifcfg-eth1: DEVICE=eth1 HWADDR=00:1E:C9:E8:3F:E7 ONBOOT=yes USERCTL=no MASTER=bond0 SLAVE=yes ifcfg-bond0: DEVICE=bond0 ONBOOT=yes BRIDGE=br0 USERCTL=no ifcfg-bridge0: DEVICE=br0

Hi, last weekend I've updated samba and ctdb on my 2-node cluster. Samba is now on 3.5.6 (from 3.3.4), ctdb on 1.0.114 (from 1.0.84). Both installed from repo via yum and ctdb-packages. After restarting both nodes everything was fine, we could access files on the cluster. On monday I noticed that the nodes didn't had their initial adresses: Node 1: hostname dscln01, public IP

Hi all, Someone played with kickstart bonding with centos 6.4 ? CentOS 6.4, as upstream now support ifcae bonding in kickstart network section. I've an issue with configuring a second bonding iface in kicstart on CentOS 6.4. The first bonding (bond0) works as espected but the second is not configured during installation. I've a 6 nic server (two for "puclic" network, two for

Guys, good afternoon I'm using in my bond interfaces as active backup, in theory, should assume an interface (or work) only when another interface is down. But I'm just lost packets on the interface that is not being used and is generating packet loss on bond. What can that be? Follow my settings bond [root at xxxxx ~]# ifconfig bond0 ; ifconfig eth0 ; ifconfig eth1 bond0

I have a machine I just deployed w/ tg3 interfaces, I have setup bonding on this same line of server (HP DL380 G4) a million times. I saw there were changes recently to how you configure a bond and have my setup configured according to: http://kbase.redhat.com/faq/docs/DOC-7431 The HP switch has a LACP trunk defined on the two ports. Problem is, when rebooting, I need to issue a `service network

Hi! I just upgraded a machine to 7.7.1908 and the default route is not being set on boot. This particular server has a bonded interface, and the corresponding configuration for the master is ( /etc/sysconfig/network-scripts/ifcfg-bond0): TYPE=Bond BOOTPROTO=none DEFROUTE=yes IPV4_FAILURE_FATAL=yes NAME=bond0 DEVICE=bond0 ONBOOT=yes IPADDR=10.3.20.131 PREFIX=24

I was given the challenge recently of creating a LAN-LAN bridge between two buildings several hundred metres from each other, using only existing Cat 3 wiring and without having to resort to an expensive and finicky 5 Ghz wireless link. I was able to create a 90 megabit link for about $3,000 Cdn with new PC's, CentOS 4.1, and the newly avaliable Black Box VDSL Ethernet Extender, which

Hi all, I use CentOS5.x + Xen in production for virtualization. I use it with bridged vlan networks and bonding (active-backup) like that: eth0 eth1 | | ------- | bond0-------bond0.10---------bond0.12 ... | | | | vlanbr10 vlanbr12 dom0 | | ------------- -------------- | |

Am 28.03.16 um 12:12 schrieb Leon Fauster: > Am 28.03.2016 um 11:27 schrieb G?tz Reinicke <goetz.reinicke at filmakademie.de>: >> We have three supermicron servers with two 10Gb Ports each, connected to a cisco switch stack 1Gb ports. All are on auto speed. >> >> I configured a LACP bond on both sides on all servers, first with citrix xen server. >> >> On

Hello All, I seem to have run into a bug with the new --bridgeslaves=<INTERFACE> option. It would seem that if I tell the bridge device to use a virtual interface (like bond0) rather than a physical interface (em1/em2) that kickstart completely barfs on it. I have provided my network section below which works fine as long as i don't enable all the bridge content. When the

Hello everyone I am running into some strange issues when configuring networking interfaces on my physical server running Centos 7.5. Let me give you an overview of what's going on: We have a physical server, running CentOS 7.5. This server has one 4 port NIC and one 2 port NIC and a Dell IDRAC port. The first port of the 4 port NIC, em1, is used for Management traffic. The first port of

Hi *, I'm running into a problem configuring bonding on an HP DL 360 G4p, running 4.3 + tg3 driver version 3.43f. I'm connecting eth0 and eth1 to a Cisco 2948 (CatOS 8.1(3)) and receiving flapping notices. The ethernet address is that of the primary interface. I have tried several different modes, including balance-rr (0), active-backup (1), and balance-alb (6). All have the

*Hi all, I''m not quiet sure the most reasonable way to dealing with bonding on xenserver. My configuration is as follow. It was ok if i do nothing, but When I tried to ''service network restart'', the bond is break. Then, /proc/net/bonding/pbond: Slave Interface: eth0 eth1 was down bonding MII status: down My questions are: how to deal with this situation? how to avoid

Dear All, I have configured Cluster Suite with 2 servers Server 1 : 192.168.13.110 IP Address and hostname is primary Server 2 : 192.168.13.179 IP Address and hostname is secondary Floating : 192.168.13.83 IP Address (Assumed by currently active server) I have configured Ethernet Channel Bonding in Each Cluster Nodes and Channel Bonding Configuration Details are 1) Created bonding devices in