similar to: Request for feedback

Hi all, I am trying to get some decent speed out of a vanilla Debian (Proxmox) box and am running out of ideas. Basically I can exchange data at 110MB/sec (raw, nfs, ftp) but not with Samba shares. I tried almost every samba tuning tip I could find to no avail. The only optimisation left to smb.conf at the moment is debug level = 0. As one can see the robocopy throughput is merely half of what

I have some questions about the choice of SSDs to use for ZIL and L2ARC. I''m trying to build an OpenSolaris iSCSI SAN out of a whitebox system, which is intended to be used as a backup SAN during storage migration, so it''s built on a tight budget. The system currently has 4GB RAM, 3GHz Core2-Quad and 8x 500GB WD REII SATA HDDs attached to an Areca 8port ARC-1220 controller

I have two Samba servers configure similarly. One shares fine across our entire network and the other only works within its own segment. I have poured over the smb.conf files and cannot see what it preventing the one from crossing segments. These both are Debian 2.2 boxes and I am just modifying the default smb.conf files. I am hoping a fresh pair of eyes will help. Any help would be greatly

I had translated TOSHARG into Japanese. I found TYPO in the paragraph of "About the Cover Artwork". The contents are as follows. ---------------------------------------------------------------------------------------- the actions of those who have travelled lifes' road before us, ------ life's

Hi everyone, i''m currently try migrate my mythtv-server into an xen maschine but the ivtv-driver for my Hauppauge PVR350 doesn''t work. Now, a lot of googling and reading later i''m now here. I''ve an error which i can''t exactly allocate: is it an driver or an xen generated error ? I got with the ivtv-drivers following error: (0.2.x ivtv driver)

Hi all, I'm confused of small files (no bigger than 50k ) transfers speed through samba,which is very slow on my machine. Bellow is a real case, -- SuSE professional 9.2, kernel 2.6.11,Samba 3.0.14a,reiserfs -- Dual AMD Opteron,4G mem,Giga byte LAN -- 2 raid 5 make up of 16 SATA hard disks -- set readhead to 1024 I tested raids speed using bonnie++ and get 450 Mbytes/s at 16GB files

Now, TOSHARG-VFS.xml translate to Japanese finished(3.4.0 base). And some bug found. <indexterm><primary>UID</primary></indexterm> <indexterm><primary>GID</primary></indexterm> <indexterm><primary>SID</primary></indexterm> <indexterm><primary>idmap uid</primary></indexterm>

Dear list, I compiled Samba 3.2.0 document like this. cd samba-3.2.0/source configure ... ... ... cd ../docs-xml make all but some error happen. --------------------------------- # make all ... ... xsltproc --output output/manpages-3/eventlogadm.8 xslt/man.xsl tmp/manpages-3/eventlogadm.8.xml runtime error: file xslt/man.xsl line 41 element if unregistered variable list-indent

Samba 3 svn repository have samba3 source code ,but I can't find samba3 document. Under /docs directory is empty. Where is samba3 document? -- --- Oota Toshiya --- oota at mail.linux.bs1.fc.nec.co.jp NEC Computers Software Operations Unit Shiba,Minato,Tokyo Linux Promotion Center Japan,Earth,Solar system (samba-jp Staff/postmaster,mutt-j/faqomatic admin,analog-jp

Hi, I'm having some weird problem with the setup of the QoS on a bridged network. As the docs states, outbound/inbound average speed should be expressed in KBps (KBytes per second) but in order to get a maximum speed of 10Mbps (megabits per second) surprising enough I have to use 2560 on the guest (not 1280 as expected). Using 1280 units I get a speed og 5Mbps. I'm aware of peak and

Hi, I'm having some weird problem with the setup of the QoS on a bridged network. As the docs states, outbound/inbound average speed should be expressed in KBps (KBytes per second) but in order to get a maximum speed of 10Mbps (megabits per second) surprising enough I have to use 2560 on the guest (not 1280 as expected). Using 1280 units I get a speed og 5Mbps. I'm aware of peak and

I have 2 samba server. both server is multi homed server. mostly same smb.conf. First server, run on FreeBSD 5-Stable,and this machine register two NetBIOS name to IP adress mapping to wins server. And this machine is m-node. Another server ,run on Linux,and this machine register only one NetBIOS name to IP adderss mapping to wins server. And this machine is h-node. I have a question. 1) Why

Hi, i am using dovecot 2.2.33.2 on CentOS 7.4. Since i upgraded from CentOS 7.2. to CentOS 7.4. (without upgrading dovecot), my dovecot sieve-pipe scripts crash with Out of memory: Out of memory (allocated 262144) (tried to allocate 8793 bytes) There are some memory limits in dovecot or sieve? Can i change this value? Kernel limitks: [root at xxx software]# ulimit -a core file size

Hi, perhaps this? > with new debian9: > open files (-n) 1024 Regards Urban Am 16.09.20 um 12:57 schrieb Maciej Milaszewski: > Hi > Limits: > > Where all working fine: > > core file size????????? (blocks, -c) 0 > data seg size?????????? (kbytes, -d) unlimited > scheduling priority???????????? (-e) 0 > file size?????????????? (blocks,

Version: 3.0.14a (debian stable: 3sarge1) I'm just about finished converting our company's network from NIS to LDAP. Part of that involved updating Samba to use that same directory so all the information is maintained in one place. Most everything is good, except that my roaming profiles won't work. My smb.conf file is attached. Upping the log level eventually showed messages

Hi guys, I''m running a freenas domU (FreeBSD 8.3 based, ZFS v28, 2 vcpus mapped to the same HT capable core) to serve storage for all purpose including other domUs running on the same host. I did some study to understand how well it works and the result is kind of confusing. In summary, the network performance between domains on the same host is worse than expected. And NFS service to

Hey, one more question for ipp2p iptables -t mangle -A DSL-IN -p tcp -m ipp2p --ipp2p -j CONNMARK --restore-mark iptables -t mangle -A DSL-IN -p tcp -m mark ! --mark 0 -j ACCEPT iptables -t mangle -A DSL-IN -p tcp -m ipp2p --ipp2p -j MARK --set-mark 7 iptables -t mangle -A DSL-IN -p tcp -m ipp2p --ipp2p -j CONNMARK --save-mark iptables -t mangle -A DSL-IN -p udp -m ipp2p --ipp2p -j MARK

I have a Dell server with four bonded, gigabit interfaces. Bonding mode is 802.3ad, xmit_hash_policy=layer3+4. When testing this setup with iperf, I never get more than a total of about 3Gbps throughput. Is there anything to tweak to get better throughput? Or am I running into other limits (e.g. was reading about tcp retransmit limits for mode 0). The iperf test was run with iperf -s on the

Anybody knows about one bandwidth meter to use in Bering. This is a script i built, it''s works wel, but it''s not very nice!!! =P #!/bin/bash # Bandwidth Monitor device=eth0 bytes=`grep $device /proc/net/dev | cut -f 2 -d : | cut -d '' '' -f 2` kbytes=`expr $bytes / 1024` actual=$kbytes i=1 x=0 total=0 while [ $i -le 2 ] do x=`expr $x + 1`