similar to: Polycom Phantom Ringing

On the polycom soundpoint ip 650 six line phone: Say I have 4 lines on hold, is there way to tell who I put on hold. I cannot see the caller ID of the other lines, only the last line I placed on hold. Thanks, --E -------------- next part -------------- An HTML attachment was scrubbed... URL:

I am posting here since you guys are my last hope. I am trying to configure a Polycom Soundpoint IP 335 with MWI. Is there any way to eliminate the scrolling messages and Msgs softkey? I am trying to get it where it's just the light that indicates the new messages. I don't know if Asterisk has to send a different notification or what have you. Thanks, --Eric -------------- next

On Tue, 4 Jan 2011, Andy Graybeal wrote: >> The Polycom 321 has not been EOL'd and supports VLAN. It is, however, >> lacking a 2nd ethernet port if you were to go that route. >> >> -M >> > Thanks for the response Mark. I see the 331 has two ports and the same > features as the 321. > > I'm wondering what phone would be best being used as an

Hi Everyone, 1- Are the Siren7 and Siren14 the G.722 HD voice codecs? 2- Are these codecs only for Polycom units or are they universal across all other SIP phones that advertise the HD voice codec like Aastra? 3- What is the main difference between the two and is it advisable to run these over the INTERnet (not INTRAnet)? Thanks -------------- next part -------------- An HTML attachment was

I have quite a number of users complaining that when they are using handsfree to talk over a landline, the other end can't hear them. It's like the person is speaking 5 feet away and can barely hear their voice. However between internal SIP calls, it's fine. What could be the problem? -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi Gang, Running Asterisk 1.4SVN using Polycom 501 phones. Just enabled CallerID and for the most part it works as good as you'd expect anything to from the phone company to. Except: on about 1 out of 10 transfers, instead of getting a callerid of "joe cool <100>" or "abc company <205-555-1212>" I just get "asterisk". Here is what

When you perform an attended transfer, the extension of the person transferring is displayed to the co-worker. Can I override the caller ID to display the caller's callerID during a blind transfer? Thanks, --E -------------- next part -------------- An HTML attachment was scrubbed... URL:

I'm having a major problem at one of my branch offices with "Phantom Rings" on their asterisk-based phone system. The system was originally built using 2 X100P cards and was recently upgraded to a Rhino R4FXO-EC card. The upgrade severely increased the frequency of the phantom rings. I've read everything I can find on-line about automatic testing and noise on the line and

Hi all, I have a client that is having problems with phantom calls. I have not been able to see it happen myself, but they say when it happens, the display on the phone (polycom 301's) says "Device" is calling, but when they answer the phone, there is only silence and then they hang back up and it sometimes rings again. I've been trying to track this down for a couple of

I just got a Polycom soundpoint and I set it up using the phone and web based admin. I cant seem to figure out the config files and they are confusing me greatly and I dont have time for it :) Some things are odd, like on every reboot it seems the volume I set is reset? is there any way to fix that. And the ringer seems low. - Even all the way up Anyone willing to point out a good asterisk

I have an extension setup in my extensions.conf for hold music. ext. 600. If I pick up a phone (polycom soundpoint 300 sip) and dial extension 600 I hear the hold music playing. If I call another extension and pick it up and put the call on hold with the hold button on the phone I hear nothing at all. Does anyone have any experience with these phones and getting the hold button to work?

Has anyone been able to get the minibrowser on the Polycom SoundPoint IP 500/600 phones working? If so could you share the relevant sections of your config with me?

Hi, I just moved many Polycom phones from firmware v3 to 4.0.1b. Anto-Answer simply stopped functioning. I can downgrade and make it work, upgrading kills it again. There obviously is a difference in how the newer firmware is treating this auto answer sip header. Can anybody tell me if they have Polycom firmware 4.x.x working with auto-answer/paging? Just so I know it's worth my time

Hi We've setup an Asterisk PBX recently and I encountered the following problem: When [mac address]-registration.cfg file includes the FQDN of the Asterisk PBX for the Polycom SoundPoint 501 phones it will not (even try to) register with the Asterisk PBX unless the DNS (it asks) successfully resolves the name: _sip._udp.[Asterisk FQDN]. Did this happen to anyone else? PS - The

I've got a couple Shoreline IP phones, their Shoreline model number is Shoreline IP 100. I believe this is actually a Polycom SoundPoint IP 300 phone. I believe the phone is using a MGCP stack. I want to use it for testing with Asterisk. 1. I suspect I need to re-image the phone to make it work with *. 2. How can I preserve the current image on the phone? 3. What is preferred image to use

Hi, What is out there in terms of SIP enabled handsfree speakerphones? Looking for something that works well and also fits a low budget. I am used to using a Cisco 7940. It is a great phone but a bit expensive. Thought about the Polycom SoundPoint 300 until I realized that it does not include speakerphone functionality. Thanks, Adi

Does anyone have the polycom soundpoint ip's successfully remotely provisioning? I've got the phone pulling default configs, and it's downloading phone specific information, but it's not actually using that information. Any help would be appreciated :) -- Aaron Daniel Computer Systems Technician Sam Houston State University amdtech@shsu.edu (936) 294-4198

Hi all, I have a Polycom Soundpoint IP 600 that looks like it is fried. It either has a bad or corrupt bootrom (I'm guessing). It never gets to the prompt that asks if I want to enter the setup configuration or continue booting. When plugged into power, it turns on, shows the Polycom logo for 3 seconds and then pretty much goes dead with two red lights on. The one in the top right corner

Problem: Polycom SoundPoint IP phones (running SIP) ceases to send DTMF that Asterisk can detect and use. It worked in 1.0.5, but has not worked since. This has been verified on SoundPoint IP 300's and SoundPoint IP 600's. Workaround: It used to be that for DTMF to work, I had to set the mode in sip.conf to "inband". Without making any configuration changes on the

Hello all, Has anyone used the SIP version of this phone with Asterisk? I see Polycom has a H.323 and MGCP version also, does anyone know if you flash the phone to swith protocols? Thanks in advance for the info. Ed -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031029/a9377305/attachment.htm