similar to: 1.8.4-rc2: ReceiveFAX fails

We have two asterisk back to back connected over PRI T1 and i am testing FAX over T1 line. Its working fine and i am getting fax file as well but i got "WARNING T.30 ECM carrier not found" is it safe to ignore this WARNING ? spandsp-0.0.6pre18 Asterisk-1.8.3.3 [from-pstn] ;Fax testing exten => 8000,1,Set(FAXFILE=/var/spool/asterisk/fax/${CALLERID(num).tif) exten =>

Hi all, I have problem for receiving fax from multiple page fax that sent from fax machine (analog). The error is : WARNING T.30 Page did not end cleanly This is my dialplan [inboundfax] exten => s,1,NoOp(**** FAX RECEIVED from ${CALLERID(num)} ${STRFTIME(${EPOCH},,%c)} ****) exten => s,n,Set(FAXOPT(ecm)=yes) exten =>

Hello! I?m trying to add fax functionality to my asterisk installation. Right now I?m focusing on receiving faxes. This is not explained in a book, but I assume that I can use same context, add ?fax? extension and if someone calls to send fax - it will autodetect. Right? Per book, I made following setup additions: 1. In sip.conf [general] I added: ;FAX stuff faxdetect=yes t38pt_udptl=yes 2.

Hi, On a new Raspberry2 with Asterisk 11.13.1 binary-installed, ReceiveFAX exits with FAILED status. Each attempt is made with something like: channel originate Local/12345 at faxgateway application SendFAX myfile.tif I'm not sure if failure "mostly" comes from SendFAX or from ReceiveFAX but it fails with 100% rate. uname -a output is: Linux myhost 3.18.7-v7+ #755 SMP PREEMPT

Hello, We have been working with the ReceiveFax application for some weeks now in order to receive faxes in T.38 and it works fairly well, but there are some faxes that for some reason we are not able to receive correctly. The asterisk version we are using is 1.6.0.6 with spandsp-0.0.5pre4 and the asterisk machine is behind a CISCO mediaGW to be able to communicate with the PSTN. The SIP call

Hello users, Recently i have installed the free version of FaxForAsterisk and trying to work with it by sending a fax on T38. My version information is as follows i)Asterisk 1.6.0.20 ii)res_fax-1.6.0.14_1.1.6-x86_32 iii)res_fax_digium-1.6.0.14_1.1.6-i686_32 sip.conf [general] t38pt_udptl=yes extensions.conf [default] exten => _XXXXXXXXXX,1,NoOp(Fax Incoming Call) exten =>

Is anyone else using the AMI with res_fax_spandsp.so for real-time status? I am working on migrating a FAX application from res_fax_digium.so to res_fax_spandsp.so. I have noticed that the spandsp module generates far fewer AMI status events than the Digium module and the generated events contain less information. For example when sending a fax there is no longer an event for every page. There

I am testing out inbound faxing using res_fax and res_fax_spandsp.so My system answers the call but then sets there on the ReseiveFax line then comes back with an error that it exceeded the maximum retries. How would I go about debugging this? Below is my very simple dialplan code I am using, and the fax show version gives the following as well. FAX For Asterisk Components:

Hi all, I am running to the following problem, when using the below dialplan to receive fax, everything works perfect till this line exten => receive,n,ReceiveFAX(${FAXFILE}): and then the following line cannot be executed, it's like asterisk can't go back to dialplan and continue, the good news is when i check what is received in my fax folder i find that the file is a valid one (not

Where can I get the latest stable version of spandsp. That will work with res_fax_spandsp.so. The link listed on the voip-info website is dead. Any other location for download? http://www.soft-switch.org/ Thanks Bryant Zimmerman -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi all, I realize that the application Receivefax can't handle with more than one fax at the same time. In a environment with a lot of fax, some caller get the signal but the operation can't be completed. Is there a way to send busy tone to the second caller? Att, Flavio Roberto Miranda MSN:flaviormiranda at hotmail.com Skype: flaviormiranda -------------- next part

On 2016-02-17 15:32, Richard Mudgett wrote: > On Wed, Feb 17, 2016 at 5:15 PM, Ernie Dunbar <maillist at lightspeed.ca> > wrote: > >> Hi everyone. >> >> We have an Asterisk server running Debian Squeeze, with Asterisk >> v1.8.13.1 (basically, the Debian Stable version for Squeeze, but >> with some minor source code changes specific to our site).

My outgoing FXO calls are answered but have no audio in either direction if I have callprogress=no in chan_dahdi.conf. If I change to callprogress=yes then the audio returns. My chan_dahdi.conf file is listed below. Can anyone point-out why callprogress=no isn't working? #cat /tmp/a [trunkgroups] [channels] language=en context=incoming toneduration=40 ;usedistinctiveringdetection=yes

Receiving a fax with 1.6.1: == Spawn extension (incoming-pstn-line, fax, 1) exited non-zero on 'DAHDI/4-1' -- Executing [fax at incoming-pstn-line:1] NoOp("DAHDI/4-1", "Fax Detected") in new stack -- Executing [fax at incoming-pstn-line:2] Goto("DAHDI/4-1", "incoming-fax,s,1") in new stack -- Goto (incoming-fax,s,1) --

Asterisk 16 latest DAHDI 3.0.0 latest Excerpt from chan_dahdi.conf is shown below. I'm trying to enable fax detection on inbound calls so that I can take appropriate action in the dial plan. "dahdi show channel 1" shows "Fax Handled: no". Does that mean that I don't have it configured correctly? [channels] ; Span 1: WCTE2/0/1 "WCTE23X (PCI) Card 0 Span

hi folks. i recently upgraded asterisk to 1.6.1.17(from 1.2) and i'm having problems with fax. after receiving fax with the ReceiveFAX app. everything seems ok. the .tiff file was there, phone line seems to hang up. then asterisk will crash. any ideas? also i looked in the log file. this is what before it crashed: [Mar 8 12:12:12] WARNING[30115] app_fax.c: WARNING T.30 ECM carrier not found

hi,all i have just set up asterisk 1.6.0.7 rc1 with spandsp 0.0.5 pre4 to ReceiveFAX, link to a E1 (DE410P) using dahdi this can receive the fax from E1 successfully, but i see many error message in the log like this: [Mar 16 09:24:38] ERROR[23540] channel.c: ast_read() called with no recorded file descriptor. when i receive a 5 pages fax, i will see this error message over 200 lines..... it

We're having an issue where we call ReceiveFax in a context that includes a hangup extension and half the time dialplan execution doesn't continue after the fax is received successfully. Am I missing something simple here? Below is a sample call where this happened: The last log line for this channel/call is: [Feb 21 09:10:53] VERBOSE[13730] res_fax_digium.c: -- Channel

Hello, Trying to set up res_fax_spandsp. Based on https://wiki.asterisk.org/wiki/display/AST/T.38+Fax+Gateway I wrote this in my extensions.conf: exten => 306,1,NoOp(Fax transmission) same => n,Set(FAXOPT(gateway)=yes) same => n,Dial(DAHDI/3) ----->FXS port to fax machine same => n,Hangup() Call flow Im trying to pull out is as follows: Zoiper -->

Hi Guys, i am using the latest version of asterisk 1.4 (1.4.33.1), dahdi (2.3.0.1) and FFA (Applications: 1.4_1.2.0, Digium FAX Driver: 1.4_1.2.0). the issue i'm having is that i'm able to receive faxes from a website (that offer this service) but not able to receive from a regular fax machine (that is working perfect). [fax-rx] exten => receive,1,NoOp(**** FAX RECEIVE ****) exten