similar to: Asterisk and Digium TC400B

Greetings List. we're facing a strange case with my system where in the middle of the call .. after like 7 minutes (not necessarily ) the callee is unable to hear the caller however the caller is able to hear the called party. the scenario is the following. 1- 15 computers running Windows XP SP3 joining a Windows Domain Controller with DHCP , DNS, ISA Internet Acceleration Server. 2- Internet

Greetings list,this question is rather a pain in my side.. i have been trying to figure it out.. it could be simple.i have a customer with a callcenter .. we developed a CRM "Customer Relations Management" with an SIP dialers built in.the question is the following.. is it possible to force the agents (users) to use a certain UserAgent which is the one built-in our system? this way will

Hello, a local prison contacted us regarding some calling card solution. they need 4 E1s to serve 120 rooms in that prison. we are planning on using 4 servers to serve the calls and one for the database servers' specifications are: 2.8 Dual Core Proccessors 2 GB Ram 160 Sata Drive each server will be provided with 1 E1 card Questions are: 1- will those servers be able to handle that ammount

Greetings list i'm trying to connect with a VoIP provider for termination.. and they have offered us three servers to connect with one SIP Signaling server and Two Media servers .. googled for a week and didn't find a way to do this.. so my question. is it possible to be done? Asterisk server 1.4.26.3 _________________________________________________________________ The

Greetings List,Trying to interconnect with a new provider.. the require a?compliance?with?RFC 3261 ?so knowing less than needed about RFC documentations.. i would like to know if Asterisk is actually in compliance with?RFC 3261 or not..?Can any one help with this? Regards -- Tarek Sawah Integrated Digital Systems CCNA, MCSE, RHCE, VoIP USA: +1 347 562 2308

Hi All, I have recently installed a TC400B card into a system and am trying to get it to work. As far as I ca tell from the docco on Digiums website, there is no config as such unless you want to enable / disable only 1 codec, otherwise by default it runs as 92 channels of either. I have tried asterisk 1.4.9, 1.4.10 and 1.4.10.1 along with zaptel 1.4.4 and addons 1.4.2. The zaptel modules

Good afternoon, I'm trying to use the CLI command file convert on an Asterisk 1.4.26 server with a TC400B transcoding card. The transcoding card is working well for calls but I have some trouble converting sound files from alaw to g729. The command creates empty file as you can see below... CLI> file convert /var/lib/asterisk/sounds/fr/service_notactivated.alaw

Is there a way skip / ignore the member whose status is busy in the Queue. I have two channel member in queue and i have set the peer limit 2 for these members. I want to skip those member who are currently on the call (answered to calls) and now their status is busy, if Queue see the busy status caller will not enter in the Queue and go to the next priority. [test-queue] strategy = rrmemory

Dears Any one knows a standalone voip transcoder software name,not an ip pbx. What I want is to transcode the incoming sip calls from g711 to g723 or ilbc or g729 ..... and forward it to a media gateway .. Regards Khaled chehab ********************************************* No employee or agent is authorized to conclude any binding agreement on behalf of Xplorium with another party by

Hello, I've been tasked to look for ways to resell to others the service that one of a trunk provides.. In other words, i want to configure my current Asterisk (Ver. 1.4.26.1) with Freepbx 2.6.0 so i can act as a trunk to others.. I would provide an IP to them from one of my servers and they will use that IP to connect to me and i will connect them to my trunk/provider. If

Hi, Looking for some reliable and quality providers of USA DIDs. Any pointers ? Thx Sans -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20100623/816aecdd/attachment.htm

Greetings List. I'm facing a strange issue with one of my providers.. after sending an INVITE request my server places the call on hold.. until the call is answered.. this is happening only with this provide although i have 3 other providers i route calls through.. can anyone explain what is going on? -- Tarek Sawah / Integrated Digital Systems / CCNA, MCSE, RHCE, VoIP / +1 347 562 2308

Greetings,I'm looking for a really cheap GSM-SIP gateway, Single channel (one SIM card). any suggestions? Tarek Sawah -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20131011/794f5a49/attachment.html>

Hi List, I have a 2Mbps SDSL link which gets saturated during peak time because about I have about 3 E1 worth of g729 traffic going thru. So I'm planning to use IAX2 trunking to reduce bandwith requirement and squeeze out each and every bit of this (expensive) bandwith. I've set up two boxes (debian etch), one in a remote data center (which has plenty of bandwith) and one behing

Hello all, I have a TC400B Digium card in order to deal with transcoding and I have some trouble using it, I have a timer synchronisation problem! I would be very grateful if you have any idea to help me? It seems that the card is not correctly synchronised to the system because when I speak to one side, the sound takes 5 seconds to go to the other side, and increasing, after 30 seconds of call,

Hi Im trying to install my TC400B trans coder card when I do: modprobe wctc4xxp tail -f /var/log/messages says: May 13 14:56:36 pbx2 kernel: Registered codec translator 'DTE Encoder' with 92 transcoders (srcs=0000000c, dsts=00000101) May 13 14:56:36 pbx2 kernel: Registered codec translator 'DTE Decoder' with 92 transcoders (srcs=00000101, dsts=0000000c) May 13 14:56:36 pbx2

This is the problem: Call coming into a queue in ringall strategy, if a member (SIP) of the queue is busy when entering the queue, and this member comes free after a little time, the member never rings.. How to solve this? I changed all parameters of the queue with no results... Wath i need: If one member of the queue is busy when a new call come in to the queue, this member can hangup and

Hi Users, I was wondering if someone of you have the same thing on CentOS 64x? asterisk01*CLI> core show translation Translation times between formats (in microseconds) for one second of data Source Format (Rows) Destination Format (Columns) g723 gsm ulaw alaw g726aal2 adpcm slin lpc10 g729 speex ilbc g726 g722 siren7 siren14 slin16 g723

Hi, does anybody made G723 or G729 to work with a GrandStream Phone ? I've a Cisco here and it works fine with G723, but not with my asterisk. The bandwitdh is very important, since we will have our extensions at home. I know that I have what I pay, but the phone works with cisco. Trying to use G723 or G729 Asterisk says no codec available. Does anybody have it working with any compression

Can someone on the list confirm if Asterisk can do g723 or g729? when connecting to provider? or it is only supporting g711? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040106/1d6c78cb/attachment.htm