similar to: Asterisk 1.6 and fax

hi does any body know which version combination of spandsp/tx_fax/rx_fax will work with * 1.2.24? i tried different combo. they're either seg fault during runtime or won't compile. very frustrated :/ p.s. i know. hylafax/iaxmodem is far more stable. but i have specific reasons to use rx_fax. -- Edwin Lam <edwin.lam at officegeneral.com> Systems Engineer, Office General, Inc.

Hi, I have recently upgraded from Asterisk 1.2.15 to 1.4.2 and I'm experiencing trouble with rx_fax. I have followed instructions posted by Sems: http://www.sems.org/entry.asp?ENTRY_ID=197 I'm using spandsp-0.0.3pre28 and the app_rxfax and app_txfax from: http://www.soft-switch.org/downloads/snapshots/spandsp/test-apps-asterisk-1.4/ rx_fax and tx_fax are both enabled via make

Hello, I have bought a targeta quadbri. I want to realize a PBX server to send and to receive fax on lines BRI. I have installed asterisk and the drivers of quadbri (bristuff_0.2.0-RC7b). I downloaded and installed the module spandsp-0.0.2pre10 When i send a fax from the fax machine to asterisk, the application rx_fax saves the fax in a file on the hard disk. The problem comes when I try to send a

Hi All, With spandsp.0.0.2 pre20 installed I can't seem to send faxes with tx_fax over a Zap channel (POTS). rx_fax works just fine so no issues with libtiff and (presumably) libxml2. Basically I get 'slow carrier up' and 'slow carrier down' together with accompanying beeping noises until tx_fax times out and hangs up. This could quite possibly be a PEBKAC or n00b

Hi all I don't know what went wrong but i no longer seem to be able to compile asterisk. I first do : cd /usr/src/dahdi-linux-2.1.0.4 make clean ; make all ; make install cd /usr/src/dahdi-tools-2.1.0.2 ./configure ; make clean ; make all ; make install ; make config So far.... so good but then when i do : cd /usr/src/asterisk-1.6.0.6 make clean ; ./configure ; make all ; make install i

Hi, With 0.0.6pre3: # ./build.sh CMake Warning (dev) in CMakeLists.txt: No cmake_minimum_required command is present. A line of code such as cmake_minimum_required(VERSION 2.6) should be added at the top of the file. The version specified may be lower if you wish to support older CMake versions for this project. For more information run "cmake --help-policy CMP0000".

You now need to compile and install SpanDSP-0.0.6pre3 at least (AGX has been changed). After you've done that - try AGX again. HTH -----Original Message----- From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Olivier Sent: 11 March 2009 06:16 To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: [asterisk-users]

I downloaded spandsp0.0.6pre17 I download http://sf.net/projects/agx-ast-addons for app_txfax and found trunk/app_fax to be newer so I used that. spandsp compiled fine. app_fax compiled when loading I get: [Apr 5 08:55:54] ^[[1;31;40mWARNING^[[0;37;40m[7505]: ^[[1;37;40mloader.c^[[0;37;40m:^[[1;37;40m433^[[0;37;40m ^[[1;37;40mload_dynamic_module^[[0;37;40m: Error loading module

Receiving a fax with 1.6.1: == Spawn extension (incoming-pstn-line, fax, 1) exited non-zero on 'DAHDI/4-1' -- Executing [fax at incoming-pstn-line:1] NoOp("DAHDI/4-1", "Fax Detected") in new stack -- Executing [fax at incoming-pstn-line:2] Goto("DAHDI/4-1", "incoming-fax,s,1") in new stack -- Goto (incoming-fax,s,1) --

hi folks. i recently upgraded asterisk to 1.6.1.17(from 1.2) and i'm having problems with fax. after receiving fax with the ReceiveFAX app. everything seems ok. the .tiff file was there, phone line seems to hang up. then asterisk will crash. any ideas? also i looked in the log file. this is what before it crashed: [Mar 8 12:12:12] WARNING[30115] app_fax.c: WARNING T.30 ECM carrier not found

To provide a reliable fax solution for users connected to a Asterisk 1.6.2.6 server i have tested a few T.38 capable ATA's: - Patton M-ATA - Grandstream HandyTone 486 - Fritz!Box 7170 I have tried Asterisk 1.6.2.6 compiled with SpanDSP-0.0.6pre17 and also Asterisk 1.6.2.6 with Fax for Asterisk installed. These Asterisk servers are connected to a Cisco PGW 2200 + AS5400XM. Sending fax

Using spandsp-0.0.6-pre17, SendFax on 1.6.1.18 and ReceiveFax on 1.6.2.8. Sip.conf on both sides has t38pt_udptl = yes. -- Executing [s at fax-tx-test:3] SendFAX("SIP/side-sip-00000009", "/var/spool/asterisk/fax/20091113_1455.tif") in new stack [Mar 20 17:05:34] WARNING[6433]: app_fax.c:178 phase_e_handler: Error transmitting fax. result=49: The call dropped

Hello, In my scenario, the asterisk machine is installed behind a CISCO mediaGW in order to be able communicate with the PSTN. Asterisk is configured to use T.38 to send and receive faxes. I'm trying to receive a fax from a fax machine located in the PSTN. Apparently everything goes well: the fax machine says the transmission was successfully completed, and the fax file is successfully

Hi, I am recently updated my asterisk 1.4.1 to 1.6.2.6 because of fax service. I have installed spandsp 0.0.5, then 0.0.6 pre 17 as well because to have support. app_fax is available in menuselect and loaded into my asterisk. The upgrade went without any problems. ast*CLI> module show like fax Module Description Use Count app_fax.so

Receiving a fax pstn - pstn with 1.6.2.6-rc2: -- Executing [s at incoming-pstn-line:1] Answer("DAHDI/4-1", "") in new stack -- Executing [s at incoming-pstn-line:2] Wait("DAHDI/4-1", "3") in new stack -- Executing [s at incoming-pstn-line:3] Dial("DAHDI/4-1", "DAHDI/g0,36") in new stack -- Called g0 --

This message is pointed directly to Steve Underwood. I tought it would not be nice to directly email him with a question that interests a good part of the Asterisk community, so here it is. :) Steve, remember a few days ago when we discussed about issues on Asterisk 1.6.1.13 and T.38 fax reception? Well I opened an issue on Mantis (https://issues.asterisk.org/view.php?id=16756) and turns out it

I just want to pdf and email faxes coming in over pstn on a TDM400P. Outgoing faxes would just go out over pstn, not through asterisk. All the voipinfo , etc, howto's are quite complicated. And most use third party apps like Hylafax. I thought there was a rxfax and txfax in 1.4. And 1.6 had app_fax. I'm now using 1.4.22, but I'd go to 1.6 if it made this easier. But I've

Hi! Have probably not understand how fax is working in Asterisk 1.6. I did install: ptlib-v1_12_0 h323plus-v1_19_7 dahdi-linux-complete-2.2.0.2+2.2.0 spandsp-0.0.5 asterisk-1.6.2 asterisk-addons-1.6.2 make menuselect in asterisk-1.6.2 source directory shows: [*] app_fax But "core show applications" doesnt show me any "fax applications" and when I try to receive a fax:

Hi folks, I am having a small problem with asterisk-1.6.2.7 + app_fax on OpenBSD 4.7 -release. Everything seems to work fine. I have a macro which answers, receives the fax to a tiff, and then runs a script (mailfax) to convert that to pdf and email it. It all works perfectly except for some errors I am seeing in the console. After it hangs up I get a dozen or so messages in the cli

Hello, All. I have a problem with receiving fax through T.30. I'm calling 543 number from fax machine, then start sending fax and fax machine send document without problem. But asterisk don't receive fax. I can't find good documentation for app_fax and I'am googled this errors. Please help me. software: asterisk-1.6.2 OS: ALT Linux 5.0.1 Ark Server hardware: Digium Wildcard