similar to: VPMADT032 Failed! Unable to ping the DSP (2)!

Hello I purchased an AEX800 card to replace the ageing cheap channel bank/T1 card solution a few months ago, assuming that it would be a more robust solution for my small scale phone system. However, it appears to be anything but that. Originally implemented as a XEN dom-u virtual machine on a large server class machine, using PCI passthrough to pass the AEX800 and a small older TDM400, then

I have a AEX800 PCI Express card - sort of a TDM800 with PCI-Express. (or AEX844 - 4FXS & 4FXO) I downloaded Asterisk Now - and have got this loaded on a new motherboard (Intel with 3 PCI, 3 PCI Express - etc). (Downside on PCI-Express is the physical support the express slot gives (very little) compared with an 'old' standard PCI slot!!!) With only this card in the box....

Hi Asterisk Users, We've been experiencing some tough time regarding a new Asterisk installation connected to the PSTN via an ISDN PRI with a Digium TE121 with the optional VPMADT032 echo cancellation module. For now, I'll focus on something very specific which is summarized on this email's subject. However, here are some general facts for the context: - System pbxfri went

Hi: I?Bought TDM2400P ,with 24 FXO ports , I installed? the asterisk 1.4.28 and?dahdi 2.2.0?and then i compiled them and configured all, i pluged into 8 pstn line into the Rj connector and then i got messages on asterisk console that alarm cleared on channels 1->8??, at this step everything should go fine ,but when i try to make a call?through the TDM?there is silence and no audio,and then i

Hi pals, Pardon me if this question sound basic please. This is the first installation where I have to use the analogue card and therefore a little lusty. I have googled a lot, but though there is a lot of information about the above file, none indicate where the file lives. I have a installed asterisk and zaptel software on a fresh installation of CentOS 5. This all from source and following

The Asterisk Development Team is pleased to announce the first release of DAHDI-Linux 2.6.0 and DAHDI-Tools 2.6.0. 2.6.0 is a feature release which: - Adds support for the TE820 8-span card to the wct4xxp driver. - Decrease load time of analog cards supported by the wctdm24xxp driver. - Adds sysfs object model to facilitate persistent span numbering and early loading of modules

The Asterisk Development Team is pleased to announce the first release of DAHDI-Linux 2.6.0 and DAHDI-Tools 2.6.0. 2.6.0 is a feature release which: - Adds support for the TE820 8-span card to the wct4xxp driver. - Decrease load time of analog cards supported by the wctdm24xxp driver. - Adds sysfs object model to facilitate persistent span numbering and early loading of modules

The Asterisk Development Team is pleased to announce the release of DAHDI-Linux and DAHDI-Tools version 2.4.0. DAHDI-Linux 2.4.0, DAHDI-Tools 2.4.0, and DAHDI-Linux-Complete are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete In

The Asterisk Development Team is pleased to announce the release of DAHDI-Linux and DAHDI-Tools version 2.4.0. DAHDI-Linux 2.4.0, DAHDI-Tools 2.4.0, and DAHDI-Linux-Complete are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete In

Hi How can i know the version of my vpmadt032 firmware? Thanks Ruben

Hi All, This is a request for testing for users of Asterisk 1.4 or 1.6 with any of the following Digium VoiceBus based cards: TDM2400P, AEX2400, AEX800, TDM800P, TDM410, TE120P, TE121, and/or TE122. From a practical standpoint, this branch should allow these boards to work in more systems / configurations where IRQ misses caused problems in the past. The updated wctdm24xxp and wcte12xp

hi you, I'm having problem with voice quality on my trixbox using TDM2400B.The trixbox is connected via 20 FXO ports on a TDM2400 with the hardware echo cancel module. Echo cancel almost works, but the users hear what they describe as a 'background crackle/buzz' coming back when they talk. anyone have the same problem? pls help me. thanks a lot. my trixbox and config

Hi list, I installed 2 HB8 cards each of them with a Quad Bri modules in a HP 360 G6 running Debian Squeeze. Here is an output of dmesg wafter server has booted: [ 9.784123] wctdm24xxp 0000:0b:08.0: PCI INT A -> GSI 31 (level, low) -> IRQ 31 [ 11.847073] bnx2: eth0 NIC Copper Link is Up, 1000 Mbps full duplex [ 11.847600] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [

Hi All, I have installed asterisk 1.6.2.8 Dahdi: 2.4.0 Digium card: Digium, Inc. Wildcard AEX800 8-port analog card I have configured this card properly and it is working for calls too, But there is issue of one way audio on this outbound routes only, My voice is going to outside pstn number but i am not able to get their audio, I have disabled firewall, selinux is also off. If I am applying

Hi list: I'm having problems, with a AEX800P card when plugin on HP ML115 G5 Server, when i load the mdule (wctdm24xxp), it loads with error con dmesg, that say that is a kernel bug of invalid OPCODE 000 or something like that. If i plug the card on SUN Server, i don't have problems with the card, but the server's nvidia video card stop working :-S Any idea? Thanks. --

Hi, I have a TDM21B (A new TDM20B that just arrived plus a X400M that I already had). This card sometimes works, and sometimes only the FXO module is seen. By "works", I mean all 3 modules have the green lights on the ports on and when zaptel is loaded the log shows: Freshmaker version: 73 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module

I have a TDM21B (A new TDM20B that just arrived plus a X100M that I already had). This card sometimes works, and sometimes only the FXO module is seen. (correction to previous message that incorrectly listed X400M/S400M when I'm using only the single port versions of these modules (X100M/S110M). By "works", I mean all 3 modules have the green lights on the ports on and when

Hi - I had a client recently move their asterisk system (asterisk 1.4.26, dahdi 2.2.0.1, aex800 w/vpm module) to a "new" location, a building that's nearly 150 years old. I was not personally able to go there, but the person who did the move said the building's demarc room was "scary"-- water leaks, jumbled and frayed wiring, and all sorts of other fun. The echo on

Hello, I have several customers describing something like annoying "silence suppression". So I did some tests and I can confirm. After disabling echo cancellation in zapata.conf the "silence suppression" effect is gone, but there is a little echo of course. I do not have this problem on other boxes where I am using oslec as an echo canceller. All my calls are SIP to ZAP (E1).

Hi all, After reading great things about the OSLEC Echo Canceller (http://www.rowetel.com/ucasterisk/oslec) and seeing the reactions of people who have tried it on a recent Trixbox thread (http://www.trixbox.org/forums/trixbox-forums/open-discussion/need-people-echo-problems), it sounds like it is the "bees knees" for sorting out echo problems with cards like the x100p. Has anyone