similar to: Dahdi 2.3.0.1 fails to compile in Xen DomU

Hello, The harddisk of my etch/bristuffed asterisk1.2 box finally died. I moved the cheap (1397:2bd0) HFC-S card to a squeeze host (i686) and built dahdi modules 2.3.0.1 using m-a. After zaptel->dahdi and asterisk 1.2->1.6 config adaptations, everything seems ok, except for the BRI side, unable to bring layers 1/2 up. Asterisk reports: chan_dahdi.c:12393 dahdi_pri_error: 1 Unable to

Hello list, I'm facing a little issue with dahdi attempting to load the OSLEC echo canceller into my current kernel. After compiling dahdi 2.3.0.1 with OSLEC support, I get the following error when set 'oslec' as the echocanceller: DAHDI_ATTACH_ECHOCAN failed on channel 1: Invalid argument (22) - Similar errors are *NOT* present using other echo canncelers. - I tried adding the

Hi, I would appreciate some advice on the following: how does one use a single BRI port HFC chipset based ISDN cards with the latest DAHDI, libpri and Asterisk 1.8? For Asterisk 1.4 I would first install mISDN & mISDNuser and then build Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is supported by the latest DAHDI & libpri but reading the source of the

Hello, # rpm -qa | grep kernel kernel-headers-2.6.18-274.18.1.el5 kernel-PAE-2.6.18-128.el5 kernel-devel-2.6.18-274.18.1.el5 kernel-PAE-devel-2.6.18-274.18.1.el5 [root at localhost ~]# uname -i i386 Trying to install dahdi-linux-complete-2.3.0.1+2.3.0 on CentOS but get below error. Can you please assist in this? [root at localhost dahdi-linux-complete-2.3.0.1+2.3.0]# make make -C linux all

CENTOS 5.5 dahdi 1.4.3.0.1 uname -r 2.6.18-194.3.1.el5PAE [root at localhost dahdi-linux-2.3.0.1]# service dahdi start Loading DAHDI hardware modules: FATAL: Module dahdi not found. wct4xxp: FATAL: Module wct4xxp not found. [FAILED] wctc4xxp: FATAL: Module wctc4xxp not found.

Hi to all, I am searching to make work an Asterisk, with an ISDN card with Cologne Chipset. Here is the lspci: 01:09.0 Network controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02) Subsystem: Cologne Chip Designs GmbH ISDN Board Flags: bus master, medium devsel, latency 16, IRQ 5 I/O ports at c400 [size=8] Memory at fdefd000 (32-bit,

Hi, It's the first time i try to configure an ISDN card with dahdi, so my experience is very poor (be kind ;)) My problem is with dahdi_genconf, when i start it it says: /usr/sbin/dahdi_span_assignments: Missing '/sys/bus/dahdi_devices/devices' (DAHDI driver unloaded?) Command failed (status=256): 'dahdi_span_assignments dumpconfig > /etc/dahdi/assigned-spans.conf' at

On 8/08/2018 5:29 pm, Thore B?decker wrote: > Hey, > > you mentioned that dovecot builds fine, but does "make check" also > complete successfully with a glibc-2.28 build on a glibc-2.28 system? > > We have been seeing segfaults during "make check" and it seems the following > patch was able to make the testsuite run successfully. > > Just out of

I have a virtual server with godaddy but can not compile DAHDI as it complains that I do not have the correct kernel source. The package installed is - kernel-devel-2.6.18-164.11.1.el5.i686: Package kernel-devel-2.6.18-164.11.1.el5.i686 already installed and latest version Nothing to do uname -a returns: Linux ip-XXX-XXX-XXX-XXX.ip.secureserver.net 2.6.18-028stab064.7 #1 SMP Wed Aug 26 13:11:07

Looking for some help from the UK please. I backed up all my Asterisk configuration before re-installing the server from 32 -> 64 bit. Unfortunately I did not transfer the backup to another machine!!!!! I now have a TDM400P that is not picking up the line. Can you see what I have done wrong when I have rebuilt the config please: dahdi_scan ---------- [1] active=yes alarms=OK

The Asterisk Development Team has announced the release of versions 2.3.0.1 and 2.2.1.2 of DAHDI Linux. These releases are available for immediate download at http://downloads.asterisk.org/pub/telephony/dahdi-linux. Both these releases address system compatibility issues with the wcte12xp and wctdm24xxp drivers. DAHDI Linux version 2.3.0.1 fixes a regression in 2.3.0 that could result in audio

The Asterisk Development Team has announced the release of versions 2.3.0.1 and 2.2.1.2 of DAHDI Linux. These releases are available for immediate download at http://downloads.asterisk.org/pub/telephony/dahdi-linux. Both these releases address system compatibility issues with the wcte12xp and wctdm24xxp drivers. DAHDI Linux version 2.3.0.1 fixes a regression in 2.3.0 that could result in audio

Is anybody else using the following combination: * a TE410P card (wct4xxp driver) * a BT ISDN connection * DAHDI 2.3.0.1 * Asterisk 1.6.2.9 I'm trying to configure a new box to replace a legacy system (same hardware; some old version of Asterisk with Zaptel; works lovely but hopelessly out-of-date) and not having much joy. Specifically, I couldn't get it to see a D-channel on

Hi, I've been experiencing trouble with my DAHDI channels for some time and have finally decided to try and resolve the issue. Essentially, the problem I am having is that when a call comes in, and my DAHDI phones therefore ring, Asterisk thinks that one of the handsets has picked up to answer the incoming call - whereas in actual fact it is still on hook. The call then gets instantly

Greetings all- During some recent testing and debugging, I wanted to use the 'fxstest' application. However, I found it hasn't been built when doing the standard 'make, make install' shtick with dahdi-linux-complete-2.3.0.1+2.3.0... Can anyone tell me how to build fxstest? Thanks! --Tim

What happens if you change to: signalling=bri_cpe_ptp -----Original Message----- From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Alex Sent: 01 October 2010 11:37 To: asterisk-users at lists.digium.com Subject: [asterisk-users] debian/dahdi/zaphfc - Unable to receive TEI fromnetwork! Hello, <snip> # cat

Hi, After an upgrade, I discovered yesterday strange things I would like to share here. Basically, I'me comparing platforms: The first one is a 2.6.26 (Debian Lenny) platform, with Asterisk 1.6.1.18, Libpri 1.4.10.2, Dahdi revision 8853 (must be between 2.3 and 2.5, I think). The second one is a 2.6.32 (Debian Squeeze) platform, with Asterisk 10.5.1, Libpri 1.4.12, Dahdi 2.6.1. Both are

Hi, Odd problem have just noticed in that when I call into the PBX DAHDI detects the call and hands it off to the extension, if I then hang up it still continues to process through the dialplan. This is what I have in chan_dahdi.conf: [channels] language=en echocancel=yes usecallerid=yes cidsignalling=v23 sendcalleridafter = 2 hanguponpolarityswitch=yes rxgain=2.0 txgain=3.0 progzone=uk

I updated Asterisk to 1.6.2.7 and now the user introduction in the meetme application is no longer working: [May 27 09:26:51] WARNING[2407]: channel.c:4034 ast_request: No channel type registered for 'DAHDI' -- Created MeetMe conference 1023 for conference '800' [May 27 09:26:51] WARNING[2407]: app_meetme.c:3640 find_conf: No DAHDI channel available for conference, user

I have a TDM400. Just updated Fedora 12 to kernel 2.6.32. Rebuilt and installed dahdi-2.2.1. kernel modules loaded. lsmod | grep wctdm wctdm 37233 0 dahdi 194985 1 wctdm lsmod | grep dahdi dahdi 194985 1 wctdm crc_ccitt 1549 2 dahdi,isdnhdlc dmesg: dahdi: Telephony Interface Registered on major 196 dahdi: Version: 2.2.1