Displaying 20 results from an estimated 1000 matches similar to: "Problem with wct4xxp - cannot make calls"
2006 Apr 30
2
PRI Issue: D-Channel woes
Hi,
I am about to pull my hair out after trying to get our PRI up and working.
We are switching from a Cisco gateway to an Asterisk box which provides
the 23 phone lines for our office. So, because the Cisco gateway is
working I can assume I have all the settings right (b8zs, esf, dms100,
etc) and the PRI is live (because we are switching over). When dialing
from PSTN, I get busy signal. When
2014 May 30
1
Flashing Red Lights in TE420 (5th Gen) Card
I have the following software installed in a Centos Box with a TE420 (5th Gen) card.
. Centos 6.5 64-bit
. Asterisk 1.4.22
. dahdi-linux-complete-2.9.1.1+2.9.1
. libpri-1.4.14.
Even without plugging in the ISDN into span 1, all 4 spans are flashing red.
Plugging an E1 into span 1 makes no difference.
My system.conf is just simply:
loadzone=au
defaultzone=au
span=1,1,0,ccs,hdb3,crc4
bchan=1-15
2011 Aug 03
1
TE410P hardware problems
TE410P card down.
I have three (3) TE410P in one machine running asterisk with SS7.
My problems started last week when one of my cards started switching to E1
every time after reboot. I set the following in dahdi.conf and that solve
the problem.
/etc/modprobe.d/
options wct4xxp t1e1override=0x00
Now all 4 ports on that card is down with Red Alarm. I tried rebooting the
machine and
2005 Sep 30
1
TE410P not working
I'm trying to install a TE410P this is what happens with compiled zaptel
1.0.9, 1.2-beta and 1.0.9 from http://updates.xorcom.com/iso/
this is my zaptel.conf (checked with the provider the values):
span=1,1,0,ccs,hdb3,crc4
bchan=1-15,17-31
dchan=16
loadzone=it
defaultzone=it
then I modprobe wct4xxp debug=1 t1e1override=15 and the kernel says :
Sep 30 16:12:40 localhost kernel: Zapata
2014 Jun 01
1
wct4xxp Excessive Interrupts Resulting in Unusable System or Card
Hello all-
I have a Digium TE410P in an HP DL145 G2 dual processor server that generates well over 100,000 interrupts per second (sometimes I?ve counted 160,000+ per second) generally resulting in either the system becoming swamped and unusable or the kernel disabling the IRQ the TE410P is on resulting in the spans on that card being unusable.
I have confirmed that the card is good by placing it
2009 Oct 20
2
Kernel panic w/ DAHDI 2.x/Digium TE220B
I've seen this consistently on three systems, with three different
cards, and multiple versions of DAHDI. At first I thought the issue
only occurred on newer, Nehalem-based, systems, but I reproduced it on
a Core 2 Duo box as well. I've tested with dahdi-linux 2.2.0.2, dadhi-
linux-complete 2.0.0+2.0.0, 2.1.0.2+2.1.0.2, and 2.2.0.2+2.2.0. The
card is a Digium TE220B which uses the
2006 Dec 18
2
Digium TE405P with French E1 => Red Alert
Hi
anyone have a idea for debug my digium TE405P card ?
My zaptel.conf:
span=1,1,0,ccs,hdb3
bchan=1-15,17-31
dchan=16
loadzone = fr
defaultzone = fr
My Zapata.conf:
[channels]
language=fr
context=from-E1
switchtype = euroisdn
pridialplan = unknown
signalling = pri_cpe
usecallerid=yes
hidecallerid=no
callwaiting=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
2011 Mar 30
5
chan_dahdi unknown dependency problem
So, I've compiled and installed libpri-1.4.11.5,
dahdi-linux-complete-2.4.1+2.4.1 and asterisk-1.6.2.17.1, but chan_dahdi is
not getting built. If I do a "make menuselect" in asterisk I see it listed
with XXX, meaning that dependencies are not met.
XXX chan_dahdi
Depends on: res_smdi(M), dahdi(E), tonezone(E), pri(E), ss7(E), openr2(E)
res_smdi gets built fine, dahdi is
2009 Sep 01
7
Dahdi configuraion / error
Hello
I just updated the kernel, dahdi-linux and dahdi-tools
Im also using now asterisk 1.4.26.1
And im still with a red light (not RED/YELLOW anymore):
[root at catumbela ~]# /etc/rc.d/init.d/dahdi status
### Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" (MASTER) HDB3/ RED
1 PRI CAS RED
2 PRI CAS RED
3 PRI CAS RED
4 PRI
2005 Aug 12
1
TE405P V2 changes?
Hi
I got the 2nd Gen firmware upgraded on the TE405P. I recompiled after
putting in the upgraded board but did not change any conf, but the spans
become active but will not come up.
I guess I am missing something or are the any changes to the
zaptel/libpri software that is required. I cannot find any info about
this or does this new firmware only work with latest CVS. I am using
1.0.9 with
2007 May 22
1
Kernel Panic in wct4xxp during unload on Zaptel-1.4.4
I attempted an upgrade of our production system from Asterisk/Zaptel 1.2 to
1.4 this weekend. Intially everything looked like it was working properly,
but some time in the day following the upgrade, the system died to a kernel
panic. I wasn't able to catch the entire kernel dump on the console
unfortunately.
I attempted to isolate the panic, and found that when 'service zaptel stop'
2004 Nov 29
3
TE410P lights don't blink read after the module is loaded
Greetings,
According to the FAQ "When you load the module and have no
circuit/channel bank the LED's should flash red"
I get the "knight rider" lights before the module loads, but after the
modules are loaded I don't get any lights, other equipment plugged in or
not.
The card has been on my shelf a while so I wonder if it needs a firmware
upgrade ? Can the cards
2012 Jan 04
1
DAHDI-Linux 2.6.0 and DAHDI-Tools 2.6.0 Released
The Asterisk Development Team is pleased to announce the first
release of DAHDI-Linux 2.6.0 and DAHDI-Tools 2.6.0.
2.6.0 is a feature release which:
- Adds support for the TE820 8-span card to the wct4xxp driver.
- Decrease load time of analog cards supported by the wctdm24xxp
driver.
- Adds sysfs object model to facilitate persistent span numbering
and early loading of modules
2012 Jan 04
1
DAHDI-Linux 2.6.0 and DAHDI-Tools 2.6.0 Released
The Asterisk Development Team is pleased to announce the first
release of DAHDI-Linux 2.6.0 and DAHDI-Tools 2.6.0.
2.6.0 is a feature release which:
- Adds support for the TE820 8-span card to the wct4xxp driver.
- Decrease load time of analog cards supported by the wctdm24xxp
driver.
- Adds sysfs object model to facilitate persistent span numbering
and early loading of modules
2010 Jul 12
0
DTFM Detection issues
Hi list,
I'm having trouble with DTFM tones detection. Usually, some tones are
being received duplicated in Asterisk, some not. As you can imagine,
that's a very big problem involving IVR menu options, Meetme conferences
protected with passwords, and so on.
We are currently using DAHDi 2.2.0.2, module wct4xxp, which is managing
a Digium TE220B card, with a hardware echo canceller
2010 Jun 17
1
DTMF detection issues
Hi list,
I'm having trouble with DTFM tones detection. Usually, some tones are
being received duplicated in Asterisk, some not. As you can imagine,
that's a very big problem involving IVR menu options, Meetme conferences
protected with passwords, and so on.
We are currently using DAHDi 2.2.0.2, module wct4xxp, which is managing
a Digium TE220B card, with a hardware echo canceller
2007 May 18
2
TE212P octastic initialization failure
Hi,
I'm trying to get a TE212 working on a Dell PowerEdge 1850 running
Debian etch using the latest release of libpri (1.4.0), zaptel (1.4.2.1)
and asterisk (1.4.4). The initilization of the Octasic echo canceller
seems to fail when the wct4xxp module is loaded.
[...]
VPM450: echo cancellation for 64 channels
Failed to open chip, code 00103017!
VPM450: Failed to initialize
[...]
By looking
2008 Apr 14
8
zaptel 1.4.10 regression with TE220B on Proliant DL380 G5 ?
Hi list,
After a lot of testing + troubleshooting, I guess I'm observing
what I am now calling a regression with zaptel 1.4.10 (is it?)
As such I call for peer feedback, before either asking Digium
install support or filing a bug.
Thanks in advance!
System: HP Proliant DL380 G5 with 2x PCI-X + 1x PCIe riser card
OS: Centos 5
Kernel: 2.6.18-53.1.14.el5 (also tested under
2005 Sep 07
1
ztcfg Kills My Dial Tone
I'm using two Rhino channel banks (first 12FXO/12FXS, second 24FXS).
These connect to a Digium TE210P card. I'm running kernel 2.6.10
and I've tried Asterisk (w/zaptel) 1.0.9, 1.2 beta, and CVS from today.
The results are the same for all versions:
Right after I reboot, and modprobe wct4xxp, my analog phone connected
to port 13 of the first channel bank (first FXS port) gets a dial
2014 Jul 21
0
DAHDI-Linux and DAHDI-Tools 2.9.2 Now Available
The Asterisk Development Team has announced the releases of:
DAHDI-Linux-v2.9.2
DAHDI-Tools-v2.9.2
dahdi-linux-complete-2.9.2+2.9.2
This release is available for immediate download at:
http://downloads.asterisk.org/pub/telephony/dahdi-linux
http://downloads.asterisk.org/pub/telephony/dahdi-tools
http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete
* Mostly stability patches affecting