similar to: zap calls are getting dropped (unexpected disconnect message)

Hi all. I am searching for a way to send SMS via our E1 PRI line. We are in Portugal and I have seen some Internet/TV/Phone providers (ZON for those who know it) who install normal phones with SMS support in landline. So I just found a page from PT (Portugal Telecom) stating that the SMC number is either 12999 or 129990 (

Hello List I'm trying to figure out what is wrong between my asterisk and my NEC 2400 pbx We have been trying to link them with a spare PA-24DTG from the NEC, I'm able to call an extension on the Asterisk, however the extension rings, and then immediatly hangs up I traced it back to the debug of the PRI on the Asterisk... I would appreciate if anyone could pin point what is wrong The

hi all I have a PRI line which i have connected to my asterisk server. I am able to make calls to mobile no through my asterisk server, while i am not able to make calls to land line nos. This is strange. Where do u think the? problem is , is it from the service provider or? mis configuration of my asterisk. I am from India and using airtel pri lines. Below i am pasting you my configuration file

I have a working system with asterisk 1.4.26.2 libpri 1.4.1 and zaptel 1.4.12.1 With a digium TE205p. I am trying to update to libpri 1.4.10.2. When I do, incoming calls work but outgoing does not. When I do this I "rm /usr/lib/libpri*" then just install libpri-1.4.10.2 as normal. I then do a make clean in asterisk and make distclean ,then configure, make and make install. I do

Hi Guys, Full PRI installed in Canada with Sangoma A101DE and Asterisk 1.4.21.2, LibPRI 1.4.10. Placing a call into PRI and then transfering that call out to another number. Problem is that the call rings out but the moment the other party pickups both legs of the call are disconnected give Cause code 16.

Hello, I have an Asterisk system in the UK using ISDN service from BT. My problem is that the called number is always passed to the provider with the Type Of Number declared as ?national? despite pridialplan (and prilocaldialplan) is set to ?unknown?. My questions are: - How can I find out what the effective value is for the above two variables without actually making a call? (I have very

Hi Guys, I am calling out 416-999-1111 on Channel 1 of PRI and then calling 416-999-2222 on Channel 2 of PRI. When the two channels are going to be ZAP native bridged, both channels hangup and CLI show PRI cause (16). Asterisk Verbose *(Channel 1 already connected to party)*: -- Requested transfer capability: 0x00 - SPEECH -- Called g0/4169992222 -- Zap/2-1 is proceeding passing it

Told you it was too complex of an issue :-) I figured to do this in zapata.conf and all is fine now: transfer=no That was the magic two letter which was sending a request for RLT feature on the line. Set transfer to "no" and all worries gone. Thanks for the input everyone. -Bruce On Mon, Apr 12, 2010 at 10:10 PM, bruce bruce <bruceb444 at gmail.com> wrote: > Futher check

handled. So....what do I do? Thanks, MD =1=================================================== !! Invalid Protocol Profile field 0x11 -- Accepting call from '2004000' to '111' on channel 0/23, span 1 -- Executing NoOp("Zap/23-1", "Incoming call from Meridian1") in new stack -- Executing NoOp("Zap/23-1", " From number: 2004000|

Hello List, it is a very long time since I wrote here.... It has been still in Zaptel times.... Today I am run into a related problem: I can't get a DAHDI setup to work 100%. I am configuring an Astribank XR00013 (BRI, two ISDN ports). At some degree the installation (latest DAHDI drivers, Asterisk 1.6.0.18 on Centos 5.x) works. I can get incoming calls to the dialplan context that is

picture. I know the firmware on the Nortel is old, so I'm guessing that libpri is sending something that the Nortel does not know how to handle. Is there a way to dumb down what libpri sends? From everything I've read PRI is an evolving standard - and older devices may struggle with newer extensions/developments. (This might be very handy for users trying to talk to old pbx's.) Is

I have been trying to sort this out for a while now but with no luck I have isdn <-> asterisk<-> pabx on a te205 incoming calls work fine outgoing calls seem to work fine but the call is dropped when answered I think it is to do with the line [May 8 17:51:55] WARNING[4762] channel.c: Unexpected control subclass '5' that is causing the problem but I don't know how to

I have a server running Asterisk 1.4.14, Zaptel 1.4.6, Libpri-1.4.2 on a CentOS 5 server. The server has a single TE110 card connected to a provider called Alestra in Monterrey, Mexico. Since we installed everything we have been having problems dialing certain numbers, those numbers always fail when dialed from Asterisk but if you dial from your cell phone they always go through. I once has a

I have a PRI E1 link between Asterisk 1.4.24 and Alcatel-Lucent OmniPCX Enterprise R9.0. As EuroISDN it works fine. However, I need to move to QSIG because of a firmware upgrade on the Alcatel PBX which doesn't support EuroISDN (please don't ask why). Besides, I've read somewhere that 2 B Channel Transfers "should" work with * 1.4, the latest 1.4 libpri and QSIG. So this

Hi all, I'm trying to insert a Rhino Ceros box equipped with a Rhino R2T1 dual-T1 card and running the latest version of Trixbox (2.4.2) between the central office and a Nortel Option 11. The switch at the CO is a DMS100. Basically, I'm taking the T1, connecting it to port 0 on the R2T1 card, and then connecting port 1 to the Nortel. (Actually a CSU and then the Nortel) We're running

Hi all, using latest asterisk-svn I want to reflect an video call incoming via an PRI EuroISDN channel to another outgoing PRI channel, and I want the the outgoing channel to have the exact same bearer capability < Bearer Capability (len= 5) [ Ext: 1 Q.931 Std: 0 Info transfer capability: Unrestricted digital information (8) < Ext: 1 Trans mode/rate:

Hey, I wrote yesterday about PRI dropping, which turned out to just be a regular reset of unused B-channels. This time there's a real issue. As noted earlier I have an ISDN-30 connection, a Digium TE-121 with VPMADT032 echo cancellation. These are my configurations files: == /etc/zaptel.conf loadzone=dk defaultzone=dk span=1,1,0,css,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 == ==

"RED: Loss of signal (LOS): The equipment shall assume "loss of signal" when the incoming signal amplitude is, for a time duration of at least 1 ms, more than 20 dB below the nominal amplitude. The equipment shall react within 12 ms by issuing AIS." This sounds like what is happening, and is in order with what one of the technicians said - I was about 20 dB below their

"RED: Loss of signal (LOS): The equipment shall assume "loss of signal" when the incoming signal amplitude is, for a time duration of at least 1 ms, more than 20 dB below the nominal amplitude. The equipment shall react within 12 ms by issuing AIS." This sounds like what is happening, and is in order with what one of the technicians said - I was about 20 dB below their

Hello, I have an ISDN-30 connection and a Digium TE-121 with VPMADT032 echo cancellation. Every 30-60 minutes I experience PRI dropping. @@@ /etc/zaptel.conf: loadzone=dk defaultzone=dk span=2,1,0,ccs,hdb3,crc4 bchan=32-46 dchan=47 bchan=48-62 @@@ @@@ /etc/asterisk/zapata.conf [channels] switchtype=euroisdn usecallerid=yes group=2 signalling=pri_cpe context=incoming channel => 32-46