similar to: The SIP in the Mobile Phones are not able to register on asterisk

I am talking about the SIP. Now the new mobiles (Nokia, Erecson, Panasonic, iPot, ... etc) all of them support SIP capability. They are able to register to any SIP server (by giving the IP address, username and password). Fring is one of the software that can be installed on the mobile devices and can register on the SIP servers. BUT, the new mobiles currently come with built in SIP (no need to

Dears; To patch libpri: I just place the patch file in the libpri source directory and then I run make and make install? Or I need to compile the dahdi and asterisk also? If the problem stayed, do I have to go for previous libpri version? Or for previous dahdi version and asterisk version? Regards Bilal ----------- > bilal ghayyad wrote: > > But I am afraid it is a bug because I

Dear; Thanks a lot for guiding me. Is it possible that the installation libpri-1.4.11.5 newer than the libpri-1.4.11.5-patch? Well, when I typed (note: I am trying to apply the libpri-1.4.11.5-patch for the libpri-1.4.11.5): libpri-1.4.11.5# patch -p0 -i libpri-1.4.11.5-patch It gave me that patched detected as shown below (example of one file, and I got same for other files): patching file

Thanks a lot for the help. But if Asterisk has private IP address and the only way to access it from remote sites is to have vpn connection to the site that asterisk existed (the site has vpn), then how that will happen from the Mobile to be able to run the softphone from the mobile? Any help? Regards Bilal ----------------- I installed out of curiosity today, and guess what? You can do SIP over

Hi All; Can anyone advise if using Cisco IP Phones in skinny protocol is fine or not? Or it is better to use it in SIP protocol? Regards Bilal

Hi All; I do not know if anyone faced such case in dealing with open vpn (as we need it for fring to be used from the mobile: Which mobile can be used to install the open vpn client on it, so we can use it to do a vpn channel with the server that has open vpn server? Regards Bilal

Hi List; I compiled Zaptel 1.4 and Asterisk 1.4 after downloading them using svn, but when I checked the file zaptel.conf under etc/asterisk, I did not find this file. Any help? By the way: How can I know the asterisk and zaptel version extactly that I compiled them? In other words, asterisk 1.4.... and zaptel 1.4.... ? Regards ------------- ITS IP Telephony and Contact Center Engineer Eng.

Hi All; Is there a softphone that can be installed on a mobile (new mobile models), so it can work with Asterisk as following: 1) As SIP or H323 client, with the ability to add button functionalities (call pickup, call transfer, ...) so if there is a wireless network, then it can use it to connect to Asterisk and work as client, but from the Mobile. 2) If there is no wireless network, then it

Hi List; How can one Asterisk Box A to send a SIP call for another Asterisk Box B, and that call to be authorized based on the username and password, and not on the IP (as the IP address of the source is not known because it keep changing)? I think the trick in the Dial command, how to write it properly in a way that other Asterisk Box can recognize the sip username and password which are existed

Hi All; My ISDN was working fine, and suddenly I start getting the below: sig_pri.c:985 pri_find_dchan: Span 1: No D-chanannel anyway! There is a Yellow Alarm, so what it could be the problem? My configuration as following: system.conf span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 chan_dahi.conf context=IncomingPSTN group=0 signalling=pri_cpe switchtype=euroisdn

Dear Alex; Thanks alot for your nice help. This is if I need to let Asterisk register with another softswitch (so I used register =>), what if I need asterisk to send call for the softswitch without register to it (directly)? If I removed the register => then how it will distiguish the IP address in the "host" at the [sip_trunk] is the IP address of the softswitch that need to

Hi All; Again, the Cisco IP Phones 7942G and using Skinny: I upgraded the firmware to version 8.5 (skinny) and I am using skinny channel (chan_skinny) and the skinny.conf file. The phones are registering, but when we use them to place a call, we only hear tooooooooooo in the handset and we do not hear voice (even when we dial the digits, we only hear toooooooo .. but it dials and destination

Hello; I need to use Cisco IP Phones with Asterisk and I have some questions to know how to use it if someone can advise: 1) How I can assign for each button an extension? 2) How I can assign for specific button a feature to be used (like call forward or call pickup .. etc)? 3) As you know that it is required to have a correct username and password to login, so where to give the username and

Hi Steve; Currently with Dahdi, for the below configuration that we were using it in the rc.local, how it will be? I think there should be something new to be used instead of ztcfg, what it is? And what about other lines? They need to be changed? touch /var/lock/subsys/local /sbin/modprobe wctdm /sbin/ztcfg -vv /usr/sbin/fxotune -s /usr/sbin/safe_asterisk Regards Bilal --- On Thu, 5/1/08,

Hi Steve; Currently with Dahdi, for the below configuration that we were using it in the rc.local, how it will be? I think there should be something new to be used instead of ztcfg, what it is? And what about other lines? They need to be changed? touch /var/lock/subsys/local /sbin/modprobe wctdm /sbin/ztcfg -vv /usr/sbin/fxotune -s /usr/sbin/safe_asterisk Regards Bilal --- On Thu, 5/1/08,

Hi Danny; Really I did not understand how I can determine if the IO will be DB or conf files? Is it from the Asterisk manager? Regards Bilal ------------------------- It depends on how you are configured. The gui interfaces using Asterisk Manager, so you get the Same IO from the gui that you would get from a native manager session. -----Original Message----- From: asterisk-users-bounces at

Hi List; Asterisk does not have any kind of cards that can work with it to be used with Digital Phones (digital phones differ than analoge phone and differ than IP Phones). Anyone can advise about this as I did not find this on Diguim Regards Bilal Ghayad __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around

Hi All; How to configure the buttons in the Cisco IP Phones to be used for different functionalities like "Call Forward, Call Pickup, ... etc"? For example, if I need to assign one of the buttons existed at Cisco IP Phone to be used for CallFrw, how to do this in Asterisk? Regards Bilal

Hi All; When the endpoint register on Asterisk or initiate a call, so they exchange the sip username and password. What is the possibility that this will be capture by the hacker and how to avoid this problem? Regards Bilal

Hi, I'm getting some strange behaviour on Asterisk 1.4 running on Debian Stable (Lenny). I suspect it's something to do with my setup, rather than a bug, but I'm struggling to see it, and would appreciate any input. Setup: PC with two ethernet cards: eth0 goes to local network, including two SIP phones (Aastra 9112i, wired, and Nokia E75, over WIFI); eth1 goes to router and