similar to: Documentation on RSA key authentication ?? (No way to send secret to peer)

Hallo Did you allow udp outgoing on 4569 as well.. i found udp bit different than tcp when comming to firewalls liaan ----- Original Message ----- From: "Bartosz Wegrzyn - asterisk" <junk@lexon.ws> To: <timebandit001@gmail.com>; "Asterisk Users Mailing List - Non-Commercial Discussion" <asterisk-users@lists.digium.com> Sent: Monday, February 21, 2005 12:29

Hi All, I am using Asterisk 1.4.26.2 and I am getting the following problem making connections to this server. My other servers are Version 1.2.x which have no problems and this 1.4.26.2 server can call the other 1.2.x servers. The error is: chan_iax2.c:4251 handle_call_token: Call rejected, CallToken Support required. If unexpected, resolve by placing address 192.168.25.250 in the

Hi, I have two asterisk servers one is connected to the PSTN and the other one is connected to SIP users. The two servers connect with each other using IAX. When I have an incoming call from PSTN to the asterisk servers and have a forward to go back out to the PSTN the two IAX channel bridge together. Now every time I dial a DTMF digit, the asterisk is sending two DTMF digits. I enable

On the asterisk1 I got this: register => username:secret@ipaddress2 [eop] username=username secret=secret type=peer host=ipaddress1 auth=md5 on the second box I got this this host is ipaddress2 [incommingiax2] username=username type=user secret=secret host=dynamic context=from-internal-custom auth=md5 on first host 1 am getting: Jun 22 14:42:10 NOTICE[2398]: chan_iax2.c:7411

Hi everyone, THis is my second thread regarding the issue.(before I was having problems with accessing my email, which slow down my responses, sorry for that) My setup looks like this Firewall | | Asterisk---Asterisk (two asterisk servers with the same setup for high avail) | | phones Ports 5060, 10000-20000, 4569, 5036 are forwared to 192.168.1.251 which is virtual ip address on one of the

hi, I use IAX softphone with asterisk and I notice that a call between two IAX softphones end after 1 min. Then I can't hear anything but the call still in progress. I have this log in asterisk IAX debug: Rx-Frame Retry[No] -- OSeqno: 002 ISeqno: 002 Type: IAX Subclass: ACK Timestamp: 00016ms SCall: 21589 DCall: 00001 [192.168.1.22:4569] Tx-Frame Retry[000] --

i have 2 asterisk servers one on CentOS and one on Fedora , i configured IAX trunking between the 2 servers so that i dial -say from a sip extension 2000 on fedora server to a sip extension 3000 on CentOS server the call seems to be established but hangup automatically after very short time and here is the iax2 set debug command result on centos server and also my iax.conf and extension.conf and

hi, i want to call PC2PC between to IAX client without authentication i want to allow every user to use PC2PC no any password required. Please let me know what i have need to do in IAX.conf or any other file to allow any user to call Pc2Pc. My IAX.conf [guest] type=user context=default callerid="Guest IAX User" My extensions.conf [default]

I received this before, and it is because you are using the wrong context in the iax.conf. For example: The context must match the username in the register statement. Iax.conf... register => username:secret@iax.host.net [username] type=friend context=iax-in user=username secret=secret auth=plaintext host=iax.hust.net ----------------------------------------------------------------

Hopefully this is really a generic question about IAX and doesn't turn out to be something specific to Teliax, because they haven't been too helpful so far. All they can tell me is that my login shows "status unknown" on their end, which prevents me from receiving inbound calls on my Teliax number. Outbound calls through the same server work fine, which rules out most networking

Hi, My asterisk server is behind firewall and i am trying to connect to FWD. i hv configured as mentioned in this link http://www.freeworlddialup.com/advanced/iax. i am able to register my server with FWD. But when i dial 393612, i always get 'No one is available to answer this time, try again later'. I hv portforwarded tcp 4569 and 5060 from my firewall to my asterisk server. Any idea

Hi, I'm trying to track down why I'm getting calls dropped on an infrequent basis between two asterisk servers which are at the same physical location and connected to each other with UTP ethernet. Here is the connection diagram Asterisk Server 1 ===UTPENET== Switch ====UTPENET==== Asterisk Server 2 I see sporadic RX and TX frame retries when I enable iax2 debugging on either box.

[ Sorry, I incorrectly copied some Reference headers into this post and tacked it onto the wrong thread. -Steve ] So far, I have been able to receive incoming iaxtel calls via my assigned 1-700-xxx-xxxx number, but only when using md5 authentication in iax.conf: [iaxtel] type=user ; Incoming calls only context=incoming auth=md5 secret=<mysecret> ; Required for

Hi, I have two asterisk servers and I want to make these servers call each other as they were internal. I have succeeded in one way. Server B can call Server A without problem, but Server A cannot call Server B. Here's the iax configuration of servers Server A: ================== [ipek] auth=rsa context=from-internal host=XXX.XXX.XXX.XXX inkeys=ipek outkey=odtu peercontext=from-internal

Dear Sanjay, Sorry sanjay i miss to explain completely. My PC2PC mean is Dialer2Dialer i want to allow call between Dialer with out any registry and authentication through IAX. so i need to setup Asterisk accept calls from any user and users can call to each other without any password and registration. please help how can i configure Asterisk using IAX in this regards. thanks, Asif Message: 9

Hello Everyone, I am trying to diagnose issue with my IAX2 extension not working. When I have iax2 set debug on all I see is this: *Rx-Frame Retry[ No] -- OSeqno: 000 ISeqno: 000 Type: IAX Subclass: REGREQ * * Timestamp: 00003ms SCall: 00130 DCall: 00000 [64.229.229.111:64823]* * USERNAME : 100* * REFRESH : 60* * * *Rx-Frame Retry[ No] -- OSeqno: 001 ISeqno: 001 Type:

Hi all, I am trying to connect to a softphone application using an Iax channel on Asterisk 1.4.30. I can do outbound calls, from softphone to asterisk, but not inbound from asterisk to softphone. I get the following Debug: ---------------------------------------------------------------------- ---------------------------------------------------------------------- Tx-Frame Retry[000] -- OSeqno:

I've been having problems with incoming IAX2 calls - some work, but a large fraction are answered with "dead air" or disconnects from my IAX provider. Disabling the jitterbuffer seems to eliminate the problem (so far)! Has anyone else seen this? I'm using 1.2.6, but I'm not sure what my provider is using. A snippet of the a failed incoming call IAX2 debug is attached

I had a working 1.0.9 asterisk installation and tried to get a Firefly IAX phone to register, but it was failing. I upgraded to asterisk 1.2.5 and the PBX is working fine, but the IAX phone still won't connect. Below is my iax.conf and the output from setting iax2 debug while the phone tries to connect. Could somebody please give me some pointers? This doesn't seem to be a normal

Hi My head hurts... Can anyone help out here, my remote IAX can see my local IAX and visa versa, conversation starts, I can dial my remote (POTS) landline number, remote end answers, trys to route to local iax2, I see it start the conversation here, the extension (SIP) rings once and then it dies... Both ends are defined with accept IPADDRESS to keep it in the family and simple.. Debug info