similar to: onnecting two asterisk using B410p BRI cards

Hi All, We've got msidn configured: Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060) iend(0x8fd5060) and running on Asterisk 1.4.21.2: pbx*CLI> misdn show stacks BEGIN STACK_LIST: * Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0

Good Evening, The company I work for is attempting to connect an Cisco ISDN Router to an OpenVOX B200P BRI Card so that we can get it to dial out across an existing ISDN PRI Line also installed in the Asterisk PBX Everything has compiled successfully and the BRI card has been detected when mISDN is started: # misdnportinfo Port 1: NT-mode BRI S/T interface port (for phones) -> Interface

Hello, I'm trying to set up a b410p rdsi card, and I'm having problems getting it up. I followed the instruction on asteriskguru and everything seem to be fine but all leds on the card are in red. [root@rdsipbx ~]# uname -a Linux rdsipbx 2.6.15.7 #2 Tue Jun 5 16:37:07 CEST 2007 i686 i686 i386 GNU/Linux [root@rdsipbx ~]# dmesg |grep Digium HFC-multi: card manufacturer: 'Cologne Chip

Hello I have just set up Asterisk Asterisk 1.4.21.2 on a CentOS 5.2 machine. I am using the OpenVox B200P ISDN card. My problem is that even though chan_misdn module seems to be loaded correctly with Asterisk (I can see it using 'module show' command) the misdn commands are not available to me in the CLI so I cannot tell if my box is correctly interfacing with the ISDN card Any ideas

Hi all, I have a "Cologne Chip Designs GmbH ISDN network controller" and I want to terminate voip calls via this ISDN card. My question is: How I must to wire the ISDN equipment with my ISDN card? With normal cable or crossover? How I can to check if ISDN card is linked with ISDN equipment? In this moment I have 1:1 cable between ISDN's, the mISDN is installed and "misdn

Its been a few days, I was wondering if anyone else has any ideas on how to get this to work? If not, could I ask a the direct question as to if anyone here has (or knows someone who has) successfully got something like a Cisco Router to successfully establish an ISDN data/Internet connection through the Asterisk PBX?

Hi everybody, i need someone to tell me the spins numbers of Rx+,Rx-,Tx+ and Tx- of TE110P and also if you can tell me have to made a cable like that?? Modem Teleco <-----------Self Crosscable------------>Asterisk Rx+ <--------------------------------------------------------------> Tx+ Rx- <--------------------------------------------------------------> Tx- Tx+

Hi. When I call my RNIS numbers (with a mobile phone for example), I can see 2 incoming calls on the IPBX, which should not happend. I'm not sure if it's a problem with the telco France Telecom and their ISDN setup, or if it's a problem with the MISDN driver on the IPBX itself. I'm stuck ... Any advices for troubleshooting that? Someone provide working configuration files

We have ISDN PCI Adapter from Billion(using mISDN). When we connect it to the PSTN the incoming calls are OK. When we try to make a call we can't do that because the ISDN port is Down: CLI> misdn show port 1 BEGIN STACK_LIST: * Stack Addr: 40400001 Port 1 Type TE Prot. PMP L2Link DOWN L1Link:DOWN Idx: 0

Has anyone tried the new ariavoice $89 VOIP desk phone with Asterisk? ` http://www.voip-info.org/wiki-AriaVoice -- Jim James H. Thompson jht@lj.net

Hi, Since a week ago I am trying to get chan_misdn working with asterisk 1.4.19, using HFC based ISDN card on Linux 2.6.22. My setup is done as detailed on wiki and FAQ. * mISDN and miSDNusers are 1.1.7.2, unpacked, build and installed. After installation and misdn-init, I have this: aragorn:root/pts/1: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) ->

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

Have you got termination set correctly? I have a B410P working with 2 x NT and 2 x TE ports successfully. I had to turn the 100ohm termination on on the NT ports (even though I have them set as PTP in mISDN.conf). HTH -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On

Hi guys, I need to interconnect an asterisk server (1.4.17) with an alcatel pbx, because i want that an asterisk extension can call an alcatel extension and viceversa. I need to do this throug a NT port (of the digium card) for technical reasons (linked with alcatel hardware). Card installation was fine, but i'm not sure of the configuration i choose. In /etc/misdn-init.conf i put my

hi list, I'm currently trying to get Asterisk running with an HFC-compatible ISDN card (no-name product, but supposed to work with Asterisk according to the packaging). the ISDN-card is connected to a alcatel ISDN-system where it should act just like a normal ISDN-phone. I went with http://www.misdn.org/index.php/MISDN_with_Asterisk and installed the package from beronet.com including:

When an error occurs in prerun_command, puppet continues execution instead of stopping. We can see the error at the log file, but puppet cotinues doing changes: puppetd[18430]: Failed to prepare catalog: Could not run command from prerun_command: Execution of ''/path/to/command'' returned 1: We want to prevent changes when an error occurs in prerun_command. Our puppet.conf:

Hi all, we're buildin an Asterisk box based on an Intel IXP425 board. The board uses a Beronet BN2S0 ISDN card, mISDN 1.1.4 and asterisk 1.4.2. hfc_multi has been patched to compile under big endian cpu, and so also capi kernel files. All the modules seem to load correctly (configuration was made with misdn-init config), but when starting cha_misdn, asterisk outputs the following lines: P[ 1]

We own an Asterisk box with the following configuration: Linux Debian 4.0 Kernel 2.6.18 Asterisk 1.2.23 Zaptel 1.2.19 We installed a Digium B410P card, and we are using 3 ports in te_ptp mode (it is connected to BRI adapters on Italian ISDN lines, provided by Telecom Italia; in Cisco language, they should be "isdn switch-type basic-net3"). Configuration strictly complies the

Hi all, We're considering using std::chrono more heavily in lldb. However, A quick search of the llvm, clang, and lld codebases shos almost zero usage of chrono. I wanted to see if this was for technical reasons (eg some compiler doesn't support it well) or simply because nobody has needed it yet. If it's the former then I'd like to be aware of the issues so we don't fall into

Hello all, Anyone expecialized with call center monitoring and reporting solution based on asterisk. A client of us, want to install a call center reporting solution for an asterisk server but I do not know which could be the best tool for that. I need a tool for reporting queue calls, agent calls, and disconnect cause. Any clue will be appreciated. Thanks in advance. VoipCrazy