similar to: PRI hunt group

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi All, I have a simple question about incoming phone line rollovers. How are these usually done? Is this done at the phone company usually, or is this something that Asterisk or channel bank is capable of? I just need someone to give me a brief explanation how it usually works, and if someone was implementing an Asterisk system, how they would go

I have about 5 incoming USA SIP lines, but my provider does not have any sort of roll-over or huntgroup feature. Does anybody have an idea on how I can create a general number that will ring to the next available, non-busy SIP line that I have? Is there a provider out there that would do this? Any suggestions would be greatly welcome. Thank you. -------------- next part --------------

Hello Everyone, I need to setup a dialplan where if a incoming call is rec'd to a number, Asterisk needs to dial several SIP extensions at the same time. The SIP extensions are for Cisco 7960s and each have multiple line appearnces. For example, exten => 9043442342,1,DIAL(SIP/102&SIP/103&SIP/104&SIP/105,,20) exten => 9043442342,1,Voicemail(u102) The issue I have is

Hello everyone, I'm sure someone had an experience arranging hunt-group setup for incoming calls on T1 PRI channels of Digium TE110P card. For instance, I have main DID channel associated with number (555) 222 0001. And I have whole bunch of other DID channels on same T1 card like (555) 222 0090, (555) 222 0091, (555) 222 0093. My goal is when a call comes to the main number which is

Ok, so I'm setting up my small office. I have my asterisk machine setup and I have 3 sip phones connected as my stations and a 4 port FXO card ready to go(planning on only using 2 lines currently). What should I now order from my telco(sbc in this case) Everytime I call, they want to sell me this expensive $50 package that bundles everything and that's for a single line. Is there a

Hi. Can you give me some hints on how I can create a rotational board? I dont even know how to spell it in english. What I want is to have more than one line reserved, but with a single phone number, so that people can call to the same number and get a ringing signal if any of the lines is available, instead of having to dial 5 different numbers in order to get a free line. This is done

Hello all, is it possible to define a pilot number in asterisk, say I have 3 direct lines and I want one of those direct lines to be used as pilot number? When that number is contacted it will be redirected to the available zap and original zap that receive it will be freed to receive another call. It can only be used when all 2 lines ares used. Thanks. Lito -------------- next part

Hello, I've got 2 analogue lines (from SBC) coming into a TDM22B. SBC have put rollover from the first to the second line. The rollover works fine when handsets are connected directly to the lines (ie when Asterisk is not involved), but when the lines are connected to Asterisk, the rollover fails: the caller just hears the line ringing, and the person on the first (busy) line hears call

In speaking to the representative at Verizon, we came to the conclusion that DID numbers were not the correct solution; however we were told by Verizon that they could do something called assign individual numbers to the PRI. What this would in effect do is give us an additional phone number that we would like to route to a specific extension; however unlike the DID number, it would not be

I'm having a major problem at one of my branch offices with "Phantom Rings" on their asterisk-based phone system. The system was originally built using 2 X100P cards and was recently upgraded to a Rhino R4FXO-EC card. The upgrade severely increased the frequency of the phantom rings. I've read everything I can find on-line about automatic testing and noise on the line and

Asterisk 11.1 We have a situation where one of our incomings POTS lines will not answer. There are 2 lines configured by the Telco as a rollover group (rings the line that is not busy) and they feed into a Digium AEX410 on the server. The most recent time this happened, I did a /etc/init.d/dahdi status and saw this: ### Span 4: WCTDM/1 "Wildcard AEX410" *53 FXO FXSKS

I have 2 * boxes. 1 has 2 PRI's from the Telco, and a PRI to the 2nd * The other has ZAP channels to Channelbanks for endusers. If someone on the second box calls a Toll Free number (it probably doesn't matter that it is toll free) that is auto answered by an auto attendant (QVC, a Bank, the Airlines, Credit Card Companies....) then the call gets dropped with in a couple of seconds of

Hello there, I'm new to Asterisk and I'm wonder what's the best way to combine multiple VOIP lines into a single phone number... I currently have 4 incoming VOIP lines, each one with a different number. Ideally, I would love to provide my customers with a single number for all those lines. Is that possible? If so, would anyone give me directions or send me a dialplan example

My goal is to have only 1 primary phone number that can seamlessly "pool" multiple VoicePulse accounts. Let's say I have 3 accounts with VoicePulse Connect 212-555-1000 (primary) 212-555-1001 212-555-1002 When I receive inbound calls on 212-555-1000, I want to "forward" or "roll over" the connection to 212-555-1001 and 212-555-1002 so that the 212-555-1000

I'm trying to see if this is even possible. When you dial ext 2000 I want it to ring my sip phone for 20 sec then call my cell and let it ring for 10 sec if I do not pick up the call on my cell I would like it to go back to * and leave a voice message for me. Here is what I have so far in my extensions.conf Everything works except the call will not go back to * after the 10 sec rule has

In the process of turning up a new pri. Zttool indicates the T1 is ready with no alarms. asterisk*CLI> pri show span 1 Primary D-channel: 24 Status: Provisioned, Down, Active Switchtype: National ISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 10000 T305 Timer: 30000 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3

Hi, I recently set up the following in a production system (2.8 GHZ Xeon, 1 Gig Memory, Dell 2650). Telco - PRI - Asterisk - T1 - PBX I am getting an occasional noticeable echo on some of the phone lines (random inbound and outbound). Everyone I ask keeps telling me that I can't be having echo since I am on a PRI, which is a digital circuit. Ok, so I can't be having echo, but I am!

With multiple inbound PRIs (and hunting across them) coming to multiple [asterisk] servers it is important to be able to do administration, i.e. control which PRIs in the same hunt group take (and which don't take) calls from telco at any given period of time. Our pre-asterisk platform uses SERVICE commands for this purpose to put B-channels into 'out-of-service'/'maintenance'

I have been getting quite a bit of PRI Resets using my Quad PRI Digium card. Prior to the resets I am getting similar notices to the following chan_zap.c:7482 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 3 Telco claims the PRI's are fine on their end and that it is my unit. Is this timing? (google somewhat leads to this) I am running 1.08 asterisk zaptel

I know this topic came up many months back and some discussions were being had on how to do this within the Zaptel drivers. However, I'm looking for even a crude hack that someone has put together to get this done. We have PRI's and LD T1's that are load balanced on two boxes. The hunt order goes from box to box as far as the spans are concerned. There are times that I would like to