similar to: Removing line 2 from CISCO 7940g

Anyone have experience with the 3-08-2 release of Cisco's SIP firmware? Are there any new features in the SIPDefault.cnf? Thanks, Ron

Hi, I am upgrading a Cisco 7960 phone from SIP V.5.1 to 6.0 and then will to go up to 7.5 However in my first attempt to go from V.5.1 to 6.0 this is hat happens: - The phone reboots - The phone then reads the file OS79XX.TXT from the TFP server. In the file I added the version "P0S3-06-0-00" - It starts upgrading firmware - Then I get the following message: (Upgrade Failed -

Hi all, i have a problem with some cisco 7960. Yesterday i did a firmware-upgrade from 3.1 (1.2) with P0S30203.bin as described in the most documents. Now i get the message Phone unprovisioned and in TFTP-Log i find the following line: 07.03.2005 19:58 :Timeout error sending P0S3-07-3-00.bin to 192.168.0.83, 0 bytes So i think it now wants to load the file P0S3-07-3-00.bin. But i have not

I know this isn't a specifically asterisk question, but does anyone know how to make the phone NOT use it's old config? I'm trying to get rid of the second line registration crap and it's not working. Aaron

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031207/e5e9b8eb/attachment.htm -------------- next part -------------- Hello all, I am newbie to Telephony world (IP and PSTN). Please excuse me if you find my questions very dumb. I am trying to configure my IP 7940 with the Asterisk, when phone boots up it only shows the message "Phone

Hi! I did manage to load phone with SIP image : SIP70.8-0-3S, made SEP-MAC.cnf.xml, but phone never read the configuration from it. On the screen it's written "Unprovisioned", and phone is not trying to register with asterisk. Please help!! MihaelaMJ -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi Everyone, I am having some issues getting my 7961 working with Trixbox. I have loaded the SIP code (8-3-3SR2) fine but when the phone boots up it goes into an unprovisioned state. A status message shows up and says ?Error Verifying Config Info?. I have read quite a bit on this topic (getting 7961?s to work with Asterisk and TB) and only came across a few postings where other people

I have a stupid question. How do you remove line presentations on a cisco 7960 ? I have 3 line presentations I don't use anymore and I can't figure out how to remove them.

Using X-Lite FWD soft phone, I can register, get to the 'demo' menu extension, but that's it. Audio starts, then after a few seconds stops, with packets still being passed. Anyoen have any clues? Yes there are firewalls between here and there, yes there is NAT at my end...What ports need punching, is rfc2833 the correct settign or should I use inband or info? TIA, I just

I'm trying to connect a Cisco 7942 to my Asterisk box. I have a 7960 and 7912 currently connected and functioning. I'm trying to use the recommendations from here: http://www.voip-info.org/wiki/view/Asterisk+phone+cisco+79x1+xml+configuration+files+for+SIP I have created a "XMLDefault.cnf.xml" and it took the latest image but the phone states it's unprovisioned? Any

I have three questions about my 7960 phone that I can't discern from the docs/wiki. 1st - If I change the SIPxxxxxx.cnf file to change registrations it sets up new lines as expected. If I delete a line it doesn't get removed when I reboot the phone. I have to go to the phone, unlock it, and reset the SIP parameters. How do I make it "forget" what it has programmed and

I've just recieved a copy of the new SIP firmware for the Cisco 7970, those of you with Cisco accounts may wish to try it (shock horror I'm sticking with SCCP). This coincides with the release of v8 firmware for all Cisco phones (and for those of you running Sergio's chan_sccp v8 works fine) The firmware is now also (and for the 7970 SIP, only) distributed in ".cop" files,

I'm starting out w/ a Cisco 7940, running the Sip image version 6.3. I've downloaded/installed asterisk via cvs. I've set the phone up to get its info via dhcp - the dhcp, tftp, astericks box & phone are on the same network. I've gone through and setup a test account per the instructions @ http://voip-info.org/wiki-Asterisk+phone+cisco+79xx but time I do a sip show

Hi all, I have seen similar discussions about this problem earlier, but I need some help here! I've been using this phone for allmost two years without any problems. Just about a week ago I had the phone unplugged for a few days and when I plugged it in again it had lost all settings, including the settings password. It was reset back to the factory default. Well, then I decided to enter

Hi, I have the following happen to me after the restart of one of my servers: out of my 3 PRIs (all configured with the same technical settings), the last one isn't coming back. It's underutilized (chances it didn't get a call since my reboot), if it makes a difference . The PRI goes from provisioned to unprovisioned, and I get this regularly: [Jun 22 09:03:48]

I have a Cisco 7940G IP Phone. I am trying to load the firmware to SIP 3.2. The Phone just hangs in Defaulting CM to TFTP Server. It doesn't do anything else after that. I also have two other 7940g's that are the Universal Application Loader mode and say Protocol Application Invalid. I need to know what I can do to fix both these problems. I am running Asterisk@Home version 1.0. I have to

Anyone have screen size + resolution for the cisco 7940g, 7960g? I'm having a hard time finding it anywhere. No vendors have the information and cisco doesn't list it. All I've been able to find is the rez of the 7940g : 100x145. -Dan

Hi, We've got a customer site with Cisco 7940G Phones connecting to our Asterisk Server via SIP. However, upon running a "sip show peers" it states that the phone is : user/user (Unspecified) D 255.255.255.255 0 Unmonitored All phones can call out via our Asterisk Server fine regardless. The problem is when they try and place a call to one another, where it

Hello everyone.... Searching the archives and google always comes up with entries regarding the "dyn" dns option in the 7960, but I can't find answers to my specific question.... My 7960 is connected via cable modem and is NAT'ed (everything is working fine). On the 7960 under SIP configuration\NAT Address I have the public IP of my cable connection. Comcast gives me a

When we were first installing these SIP phones, the time and date was displayed on the top status line. Firmware version 6.3. Using dhcp, tftp, http, and ntp servers for configuration all on the LAN (* box). Now that we have these working with *, the time/date display is missing. Any ideas? Thanks, Tom