similar to: SIP hacked connection?

Hi Just moved offices in the UK and moved our Asterisk box from old one to new one. Using idefisk softphones, Junghanns quadbri card for ISDN 2e interfaces. At both offices we had one standard number and a DDI range, routed with Asterisk. We'd set up the configuration so each idefisk set its own caller ID which then got sent by the extensions.conf script. Worked fine at old place but in

I know it is a strange arrangement but due to contracts, it is what it is, no PRI for now. I wonder if anyone on the list has run a server with both types of cards installed? Results? I have never touched a BRI except in concept and Cisco lab. Not sure what the BRI stuffed package may or may not do to anything else that might relate to zaptel or Sangoma. Thanks, Steve Totaro

Hi We've recently set up and are using with success 1.0.7 using a Junghanns quadbri card to BRI ISDN, and Firefly with IAX2 protocol as softphones Works very well, however we're getting cases where sometimes the call just drops. >From setting more verbose modes we get a log which is shown below. The problem seems to be the maxretries message which comes from chan_iax2. We are using

Hi, I'm looking for an interface card for termination of Euro-ISDN2 (BRI) lines. That is ISDN lines from the telco into my Asterisk box. Any recommendations, good/bad expiriences ? At present I'm looking at cards from BeroNet and Junghanns. Cheers, John Faroese Telecom

<P>Hi List,<BR>is it possible to connect an existing telefon system with a stanard AVM ISDN card to the telco?</P> <P>&nbsp;</P> <P>[ISDN from Telecom supplier] ---- [Aterisk Box] ----- [ existing telephon installation]</P> <P>&nbsp;</P> <P>kind regards,<BR>Patrick</P>

Hi, I'm in the process of setting up Asterisk in a SOHO environment using ISDN for trunking. More specifically a BRI 2B+D circuit where one SPID is used for the business and the other is used for personal. The circuit already exists, but is presently being interfaced to POTS phones via a TA. This configuration is not very common in the US, but we are fortunate that our LEC offers it price

Hello, I recently bought a Junghanns Octobri Card. I have some problems with this card to make outbound calls but I can receive calls. I have 3 lines to PSTN and 3 lines to my existing PBX FRANCE TELECOM <-- OctoBRI --> Asterisk 1.2.4-BRIstuffed-0.3.0-PRE-1h <-- OctoBRI --> PABX e-Generis <----> ISDN Phones |

I know the subject of faxing has been covered in some detail, but I was wondering if anyone has a hardware configuration similar to ours that has faxes working successfully and would be willing to share any settings/insight. We are unable to fax reliably with a Sipura 2100 connected to Asterisk. We do not route calls over the Internet and our network has very low latency. The Asterisk

Hi, Someone reported me that from a PBX on which someone gained fraudulent access, he could observe hundreds of calls to the same destination number. For curiosity's sake, I'm wondering why would this happen (dialing the same number over and over) ? Some special numbers generate here and there revenues for callees (and not for callers). Beside sharing interests with the callee that get

Hello, I'm having trouble working out how to send DTMF tones to an external IVR. My system has an analog phone connected to a TDM400P card, a SIP software phone (Zultys LIPZ4) and is connected to a BRI in Australia with a NETjet-S card. I'm using ISDN4Linux and a 2.4.25 kernel patched with the ISDN audio patch from Traverse (which allows the card to do voice). DTMF works fine between

Hi, After an upgrade, I discovered yesterday strange things I would like to share here. Basically, I'me comparing platforms: The first one is a 2.6.26 (Debian Lenny) platform, with Asterisk 1.6.1.18, Libpri 1.4.10.2, Dahdi revision 8853 (must be between 2.3 and 2.5, I think). The second one is a 2.6.32 (Debian Squeeze) platform, with Asterisk 10.5.1, Libpri 1.4.12, Dahdi 2.6.1. Both are

hello, anyone has worknig ISDN hfc-pci card in DDI (DID) point2point mode? what kernel ? and second question mISDN driver .. anyone has working solution with mISDN and maybe fritz card? what you suggest for DDI -> point2point mode (card,kernel,chan_..., ...) ? thank you, Tomaz

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Does anyone have any recommendations on an IAX Desktop Telephone or ATA Device. I currently have 2 of the SIPURA-841's on my local network and now I am wanting to try an IAX Device at my remote office since I think that it would be easier to configure through various routers than a SIP Device. I just started to look at the Digium IAXy Single FXS

Having ISDN FXOs and a bunch of ISDN DECT base stations, I went looking for a CAPI compatible active BRI adapter capable of NT mode. I have found that the 'Eicon Diva Server 4BRI' fulfills theses requirements. However, at EUR 1387 for four BRI interfaces, it does not come cheap. Are there other users of similar hardware that can point me to alternatives ?

Hi there I am in the UK.. and am running latest asterisk on FC1 (2.4 kernel). I would like to know what the best option is for a 4 port BRI card. I notice Digium don't provide one.. I have heard the Junghanns do one...but are there others ?? Is the Junghanns card reliable/stable with good sound quality ?? I notice it is very expensive in a per port comparison with the Digium cards.... hence

Hello all, Recently I purchased an QuadBRI card from junghanns.net after some playing around, reconfiguring dialplans etc with the exception of 1 thing everything seems to work: I seem to be unable to set the outbound callerid. The dutch telecom operator (KPN) provided me with 4 MSN's on 1 BRI interface. In the past years I'm more then used to setting the MSN without the leading 0, this

Hi All I have a Junghanns BRI 4 port installed where only the first channel of each line is working i.e. channels 1 and 4 work but 2 and 5 don't. Our config is the same on this box as 15 other similar installations where all works well. the only error I see is in /var/log/messages: Jun 28 15:49:31 pbxct kernel: qozap: CRC error for HDLC frame on card 1 (cardID 0) S/T port 2 Jun 28 15:51:27

Hi, Can anyone please point me in a direction as to how to set up these 2 pci cards with AAH 1.1? I have (am still) googling left, right & center - but haven't found a definitive guide yet. The centos based setup lacks any of the tools I know (insmod, modprobe ....) so it is time consuming just to even dig around the AAH box. There are no zaptel.conf files ....and on it goes. A

We are looking to lose the TDM400P in favor of an ISDN-BRI solution. This should get rid of static on the line (at least any static generated by our half of the circuit), right? I am a total virgin to ISDN. I understand that we need two BRI circuits to provide four voice channels, and that the hardware to speak to the BRI circuits can be passive or active, with the active type being much more

I have a North American BRI configured as National ISDN (NI-1) on an SBC (Nortel?) switch. SBC calls this "FastTrak ISDN", and it's surprisingly inexpensive -- less than two POTS lines. I've been trying to find an inexpensive PCI interface solution to connect this to Asterisk as voice lines. I prefer ISDN BRI over POTS lines because of the improved signalling, fast dialing,