similar to: Sangoma A200 wt HW echo on 64bit Centos , 4 fxo and crosstalk!

I've been using Asterisk 1.2.6 with a 4 port FXO Sangoma A200 card for the past month without many problems (other than the fact that the Sangoma card doesn't disconnect hung up calls immediately, which I posted about in another thread, and has still not been fixed), however, I had a call from one of our clients today and they complained that our phone system kept ringing through when they

Hi All, I'm struggling with an intermittent crosstalk issue resulting in a caller's audio being broadcasted to other calls (only one way as they are unable to hear the others listening in). Doing do diligence I've scoured the web in hopes of triaging the issue. So my thoughts are leaning towards this NOT being an Asterisk issue, but instead being related to the telco (PRI)

Hey Guy, I have ubuntu 10.04 64bit and compiled dahdi / wanpipe 3.5.19 /asterisk-1.8.x I didn't understand what is the relation between wanpipe and dahdi ? do i need to start wanrouter service ? I am getting weird errors and my system got kernel panic many time when i restart dahdi service. any idea ? what is the startup sequence of all these service ? root at example:/etc/asterisk#

Hi, Does anybody have an idea as to why dahdi_test results drop to unacceptable levels after doing a wanrouter stop/start using a Sangoma card? See below that it drops from 99.99% to 98.55%: [root at bin]# dahdi_test Opened pseudo dahdi interface, measuring accuracy... 99.999512% 99.992874% --- Results after 2 passes --- Best: 100.000 -- Worst: 99.993 -- Average: 99.996193, Difference:

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! I had the opportunity to test a Sangoma A200 card and I have some doubts that I would like to consult: I tried to detect the card and I had no success using the wctdm module with DAHDI. I guess this is because electronics is different because the TDM400P and OpenVox A400P cards have separate modules for each channel, while the Sangoma A200

Hi Everyone, We are using two Sangoma U100 (USB FXO) units connected to an Acer Aspire Revo (little PC running on Atom). The units work beautifully except for Monday :-) It maybe a conincedence or maybe the fact that Saturday/Sunday is off and something happens where one of these U100 modules goes into sleep and that's when all the 4 Dahdi channels are lost. So, I have been getting Monday

Hi, I have A101DE Sangoma Card( http://www.sangoma.com/products/hardware_products/digital_voice_and_data_networking/a101.html ) lspci shows as 03:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card [root at asterisk ~]# lspci -vvv -s 03:04.0 03:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card Subsystem: Unknown device

Im trying to install and configure sangoma ... every thing is OK but when type the command "wanrouter start" the following error apears: wan Driver not found. Thanks for any help

Hey List-ee's! We're on Asterisk 1.2 with a PRI/T1 and maybe 50 phones. Issue: When a conference is ongoing (meetme), if a call is placed to a PRI # (CALLER A) the audio from the conference is heard by that caller while the # they dialed is ringing in the background. The opposite also occurs where an outside caller will be heard in the conference channel as well. Frequency: 2-3 times

In my Asterisk CLI I get Ring/Off-hook in strange state 6 when i make a call into the system, the system claims to answer the call, and do the things in the dial plan, but I just hear ringing on the phone I'm calling in from. I am using a Sangoma A200 4 Port Analog card. my wanrouter version: WANPIPE Release: 3.3.6 asterisk -V: PBXtra Core fon_o_1.2.17 Any ideas? Daniel Lockard

I have installed Asterisk on a CentOS4 box and then installed Asterisk from CVS. I installed a Sangoma A101 and connected it to a Adtran 600 using a T1 Crossover cable. The 600 has 12 x FXS, 12 x FXO interfaces. I ran through the wanpipe install instructions and configured it, now I can run [root@altpbx asterisk]# wanrouter hwprobe ------------------------------- | Wanpipe Hardware Probe Info

Trying to install wanpipe 3.5.18. No errors during compile. But when I reach the point where wanpipe and dahdi_cfg is started, I encountered an error. Starting WAN Router... Loading WAN drivers: wanpipe done. Starting up device: wanpipe1 wanconfig: WAN device wanpipe1 driver load failed !! : ioctl(wanpipe1,ROUTER_SETUP) failed: : 22 - Invalid

Hi, One other question I was wondering about. Is the reason that we hear the crosstalk with fec and packet loss percentage>0 is that Opus uses information from the left channel to try to error correct the right channel and vice versa? I am trying to understand the origin of the crosstalk. Thanks. -Jon > On Jan 27, 2017, at 12:29 PM, Jon Lederman <jon at soniccloud.com> wrote: >

As far as I can tell, after discussing this matter with other asterisk users in my area, my telco _does_ provide disconnect supervision.. It seems that the problem is actually related to the Sangoma A200 card I'm using, as two other people both using this same card have expressed the same problem.. Are there any other users on this list using the Sangoma A200 FXO port card, and experiencing

Hi Guys, Looking for a powerful box that is compact, can take two hard drives for Raid-1 (no SSD, too expensive), have at least two Gig ports or two 10/100mbps ports. Fit two PCIe or one PCIe card plus it's daughter card which needs as much room as a PCIe and doesn't need the actual slot. That is for Sangoma A200 + Daughter card. I would be really glad if I can get some sort of a KVM

Hello, i am trying to install sangoma a200d to my centOS server but i am receivig this error message: ZT_CHANCONFIG falied on channel 1: invalid argument (22) Please help me on hopw to solve this issue! tnx! kenjie -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060309/fbeeb280/attachment.htm

Hi, got a Sangoma A200 with a bunch of extension cards and having real problems getting it to deal with a normal single BT line Symptoms are that incoming calls are fine. Outgoing calls ring the far end, BUT asterisk never sees that the call is answered (ie no message in the logs files saying so), as a result the remove end can hear the PBX side talking, but there is no audio back from the

Hi everybody! I'm triying to install a Sangoma A200-R FXO card on a Debian Linux 5 (Lenny), 2.6.26 kernel. To install wanpipe driver I type: WANPIPE_FOLDER# ./Setup install Everything seems to be ok. There are no broken dependencies and the hardware is well detected, even zaptel is recompiled with no errors, but at the time to compile wanpipe I'm getting this error message:

Hi, Does some one experience the Sangoma A20X-ec series card that cant detect the hangup tone? I got * server 1.2.5 and running on Centos 4.3, I hock up to two PSTN lines and each time some one call in and my phone delay 1-2 sec (this is Asterisk delay nothing to do with Sangoma) and it rings on my phone, however, end on the day I got not less that 10 empty messages. I found out that Sangoma FXO

Hi I was wondering if any one has used these cards, I am looking at this as a replacement for the tdm410, I have some issues with installing the tdm410 in a small case because of the power plug being at the end of the board. I am in australia seems like we have a different setup for out fxs voltage, any one in oz using this card ? Thanks Alex -------------- next part -------------- A non-text